{"id":14548,"date":"2026-09-17T05:31:34","date_gmt":"2026-09-17T05:31:34","guid":{"rendered":"https:\/\/www.examlabs.com\/certification\/?p=14548"},"modified":"2026-09-17T05:31:34","modified_gmt":"2026-09-17T05:31:34","slug":"cisco-100-150-practice-test-questions-and-exam-dumps-part14-q261-280","status":"publish","type":"post","link":"https:\/\/www.examlabs.com\/certification\/cisco-100-150-practice-test-questions-and-exam-dumps-part14-q261-280\/","title":{"rendered":"Cisco 100-150 Practice Test Questions and Exam Dumps Part14 Q261-280"},"content":{"rendered":"

<\/h1>\n

View Full <\/b>Cisco 100-150 Exam Dumps<\/b><\/a> and Practice Test Dumps.<\/b><\/h2>\n

 <\/p>\n

Question 261<\/b><\/h3>\n

What is the default OSPF hello packet interval timer on multi-access broadcast networks, such as Ethernet?<\/b><\/p>\n

    \n
  1. 5 seconds<\/span><\/li>\n
  2. 10 seconds<\/span><\/li>\n
  3. 30 seconds<\/span><\/li>\n
  4. 60 seconds<\/span><\/li>\n<\/ol>\n

    Correct Answer: 2<\/b><\/p>\n

    Explanation:<\/b><\/p>\n

    The Open Shortest Path First routing protocol utilizes Hello packets to discover neighboring routers, establish bidirectional communication, and maintain dynamic adjacencies within an OSPF area. On multi-access broadcast networks and point-to-point links, the default OSPF hello interval timer is set to 10 seconds, with a corresponding dead interval timer of 40 seconds (four times the hello interval). If a router fails to receive an incoming OSPF Hello packet from an established neighbor before the 40-second dead timer expires, it declares that neighbor dead, tears down the adjacency, and triggers a recalculation of the network topology to reroute traffic around the failed link. On non-broadcast multi-access networks like Frame Relay, these default timers are automatically extended to 30 seconds to conserve bandwidth and accommodate lower-speed WAN characteristics.<\/span><\/p>\n

    Question 262<\/b><\/h3>\n

    Which command is used on a Cisco switch to configure a default gateway for management traffic when routing is disabled?<\/b><\/p>\n

      \n
    1. ip default-gateway<\/span><\/li>\n
    2. ip route 0.0.0.0 0.0.0.0<\/span><\/li>\n
    3. default-router<\/span><\/li>\n
    4. ip gateway address<\/span><\/li>\n<\/ol>\n

      Correct Answer: 1<\/b><\/p>\n

      Explanation:<\/b><\/p>\n

      The ip default-gateway global configuration command is specifically utilized on Cisco Layer 2 switches when routing functionality is disabled, allowing the switch to reach remote management subnets, Syslog servers, or TFTP firmware repositories outside its local VLAN segment. Because a pure Layer 2 switch does not perform general IP packet routing between subnets, it requires a designated default gateway address to forward packets generated by its internal management IP stack. In contrast, when IP routing is enabled via the ip routing command on a multilayer switch or router, the switch relies on standard static or dynamic default routes configured via ip route 0.0.0.0 0.0.0.0 to handle packet forwarding across different network boundaries.<\/span><\/p>\n

      Question 263<\/b><\/h3>\n

      What core protocol does IPv6 utilize for neighbor discovery, router solicitation, and address resolution instead of legacy ARP?<\/b><\/p>\n

        \n
      1. Internet Control Message Protocol version 6<\/span><\/li>\n
      2. Dynamic Host Configuration Protocol version 6<\/span><\/li>\n
      3. Transmission Control Protocol<\/span><\/li>\n
      4. Routing Information Protocol next generation<\/span><\/li>\n<\/ol>\n

        Correct Answer: 1<\/b><\/p>\n

        Explanation:<\/b><\/p>\n

        IPv6 completely replaces the IPv4 Address Resolution Protocol and ICMPv4 error reporting mechanisms with the modern Neighbor Discovery Protocol, which operates directly on top of Internet Control Message Protocol version 6 (ICMPv6, protocol number 58). NDP utilizes specialized ICMPv6 message types\u2014such as Router Solicitation, Router Advertisement, Neighbor Solicitation, and Neighbor Advertisement\u2014to perform essential functions including stateless address autoconfiguration, duplicate address detection, router discovery, and physical link-layer address resolution. By leveraging multicast addressing and ICMPv6 packet structures, NDP eliminates broadcast storms associated with legacy ARP requests, providing a highly scalable and secure mechanism for node interaction across modern IPv6 local area networks.<\/span><\/p>\n

        Question 264<\/b><\/h3>\n

        Which WAN encapsulation protocol is a Cisco proprietary standard that supports multiple network layer protocols simultaneously?<\/b><\/p>\n

          \n
        1. Point-to-Point Protocol<\/span><\/li>\n
        2. High-Level Data Link Control<\/span><\/li>\n
        3. Serial Line Internet Protocol<\/span><\/li>\n
        4. Frame Relay<\/span><\/li>\n<\/ol>\n

          Correct Answer: 2<\/b><\/p>\n

          Explanation:<\/b><\/p>\n

          High-Level Data Link Control is a bit-oriented synchronous data link layer protocol used across point-to-point serial communication links. While standard ISO-defined HDLC lacks support for multiple simultaneous network layer protocols over a single link because it omits a protocol type field in its header, Cisco developed a proprietary extension to HDLC. Cisco HDLC includes a proprietary protocol type field within the frame header, enabling a single serial link to encapsulate and transport multiple concurrent network protocols\u2014such as IPv4, IPv6, and IPX\u2014simultaneously. However, because Cisco HDLC is proprietary, it can only be utilized when connecting two Cisco devices across a dedicated serial connection, whereas open standards like Point-to-Point Protocol are required for multi-vendor interoperability.<\/span><\/p>\n

          Question 265<\/b><\/h3>\n

          What is the number of usable host IP addresses available in an IPv4 subnet with a \/27 CIDR prefix?<\/b><\/p>\n

            \n
          1. 14 hosts<\/span><\/li>\n
          2. 30 hosts<\/span><\/li>\n
          3. 62 hosts<\/span><\/li>\n
          4. 126 hosts<\/span><\/li>\n<\/ol>\n

            Correct Answer: 2<\/b><\/p>\n

            Explanation:<\/b><\/p>\n

            A \/27 CIDR prefix indicates an IPv4 subnet mask of 255.255.255.224, where twenty-seven bits are allocated for network identification and five bits remain available for host device addressing. To determine the total number of IP addresses in this subnet, calculate two raised to the power of the host bits (two to the power of 5), which equals 32 total addresses. Out of these 32 total addresses, exactly two are permanently reserved for structural functions: the lowest address serves as the network identifier, and the highest address functions as the directed broadcast address. Subtracting these two reserved addresses leaves exactly 30 usable host IP addresses available for assignment to workstations, servers, or router interfaces within that specific subnet range.<\/span><\/p>\n

            Question 266<\/b><\/h3>\n

            How does the Spanning Tree Protocol elect the root bridge in a switched network topology?<\/b><\/p>\n

              \n
            1. By selecting the switch with the highest physical IP address configured on its management interface.<\/span><\/li>\n
            2. By selecting the switch with the lowest Bridge ID, which combines bridge priority and MAC address.<\/span><\/li>\n
            3. By selecting the switch with the highest number of active physical ports.<\/span><\/li>\n
            4. By selecting the switch that boots up first in the network infrastructure.<\/span><\/li>\n<\/ol>\n

              Correct Answer: 2<\/b><\/p>\n

              Explanation:<\/b><\/p>\n

              The Spanning Tree Protocol elects a single root bridge to serve as the logical center of the spanning tree topology, ensuring loop-free path calculations across all connected switches. The root bridge election is determined by evaluating the Bridge ID of every participating switch. The Bridge ID consists of an 8-byte field divided into two components: a 16-bit configurable bridge priority (defaulting to 32768) and a 48-bit burned-in MAC address. The switch advertising the lowest numerical Bridge ID wins the election and becomes the root bridge. If multiple switches share the exact same priority value\u2014which frequently occurs with default factory configurations\u2014the STP algorithm breaks the tie by examining their MAC addresses, selecting the switch with the lowest hexadecimal MAC address as the root bridge.<\/span><\/p>\n

              Question 267<\/b><\/h3>\n

              What primary architectural difference distinguishes TACACS+ from RADIUS authentication protocols?<\/b><\/p>\n

                \n
              1. TACACS+ encrypts only the password field, whereas RADIUS encrypts the entire packet payload.<\/span><\/li>\n
              2. TACACS+ separates authentication and authorization processes, whereas RADIUS combines them into a single step.<\/span><\/li>\n
              3. TACACS+ operates over UDP, whereas RADIUS operates exclusively over TCP.<\/span><\/li>\n
              4. TACACS+ is an open IETF standard, whereas RADIUS is proprietary to Cisco Systems.<\/span><\/li>\n<\/ol>\n

                Correct Answer: 2<\/b><\/p>\n

                Explanation:<\/b><\/p>\n

                TACACS+ (Terminal Access Controller Access-Control System Plus) and RADIUS (Remote Authentication Dial-In User Service) are both AAA (Authentication, Authorization, and Accounting) protocols used to secure administrative access to network devices, but they differ significantly in design and operation. TACACS+ separates authentication, authorization, and accounting into completely independent operations, allowing fine-grained control over what specific commands an authenticated administrator is permitted to execute on a router or switch. In contrast, RADIUS combines authentication and authorization into a single bundled process. Additionally, TACACS+ runs over TCP port 49 and encrypts the entire packet body after initial negotiation for maximum security, whereas RADIUS operates over UDP ports 1812 and 1813 and historically encrypts only the password field within access-request packets.<\/span><\/p>\n

                Question 268<\/b><\/h3>\n

                What is the primary operational benefit of implementing Virtual Local Area Networks (VLANs) in an enterprise campus switch network?<\/b><\/p>\n

                  \n
                1. Encrypting all data payloads against wireless eavesdropping across local links.<\/span><\/li>\n
                2. Segmenting physical broadcast domains into smaller logical broadcast domains to improve performance and security.<\/span><\/li>\n
                3. Automatically assigning dynamic IP address leases to client workstations on demand.<\/span><\/li>\n
                4. Translating private internal IP addresses into public routable addresses using port overload.<\/span><\/li>\n<\/ol>\n

                  Correct Answer: 2<\/b><\/p>\n

                  Explanation:<\/b><\/p>\n

                  Virtual Local Area Networks allow network administrators to partition a single physical enterprise switch infrastructure into multiple distinct logical broadcast domains. Traditionally, physical routers were required to separate broadcast domains because physical switches forward broadcast, multicast, and unknown unicast frames out every port within the same LAN segment. By grouping switch ports into separate VLANs, broadcast traffic is strictly contained within each individual logical segment, reducing unnecessary network congestion, optimizing CPU utilization on connected host devices, and preventing broadcast storms from disrupting the entire infrastructure. Furthermore, VLANs enhance security by logically isolating sensitive departments\u2014such as finance or human resources\u2014from general user traffic without requiring separate physical wiring and hardware switches for each group.<\/span><\/p>\n

                  Question 269<\/b><\/h3>\n

                  What is the function of the TCP sliding window mechanism during data transmission?<\/b><\/p>\n

                    \n
                  1. Encrypting session data to prevent unauthorized interception.<\/span><\/li>\n
                  2. Managing flow control by allowing the receiver to inform the sender how much data it can accept before requiring acknowledgment.<\/span><\/li>\n
                  3. Resolving human-readable domain names into numerical IP addresses.<\/span><\/li>\n
                  4. Establishing the initial connection parameters during the three-way handshake.<\/span><\/li>\n<\/ol>\n

                    Correct Answer: 2<\/b><\/p>\n

                    Explanation:<\/b><\/p>\n

                    The TCP sliding window mechanism is a critical flow-control protocol used within the Transmission Control Protocol to prevent a fast transmitting sender from overwhelming a slower receiving host with excessive data streams. As data is exchanged, the receiving host continuously advertises its available buffer capacity\u2014known as the window size\u2014within the acknowledgment headers of returning segments. This informs the transmitting host exactly how many bytes it is permitted to send before it must pause and wait for an explicit acknowledgment. As the receiver processes data out of its buffer and frees up memory space, the window “slides” forward, allowing additional data transmission. This dynamic adjustment optimizes throughput efficiency while protecting receiving buffers from overflowing and dropping packets across congested network links.<\/span><\/p>\n

                    Question 270<\/b><\/h3>\n

                    Which command verifies established adjacencies and operational states between neighboring OSPF routers?<\/b><\/p>\n

                      \n
                    1. show ip route<\/span><\/li>\n
                    2. show ip ospf neighbor<\/span><\/li>\n
                    3. show ip interface brief<\/span><\/li>\n
                    4. show cdp neighbors detail<\/span><\/li>\n<\/ol>\n

                      Correct Answer: 2<\/b><\/p>\n

                      Explanation:<\/b><\/p>\n

                      The show ip ospf neighbor command executed in privileged EXEC mode on Cisco routers is an essential diagnostic utility used to verify the operational status of OSPF routing protocol adjacencies. When invoked, it displays a concise summary table of all neighboring routers with which the local router has established communication. The output details critical telemetry including the neighbor router ID, OSPF priority values, current operational state (such as FULL or 2-WAY), dead timer countdowns, the IP address of the connected interface, and the designated router roles on multi-access network segments. Network administrators rely heavily on this command during routing troubleshooting to verify whether OSPF adjacencies have formed successfully, identify stuck states caused by mismatched hello timers or authentication keys, and diagnose dynamic routing failures across enterprise networks.<\/span><\/p>\n

                      Question 271<\/b><\/h3>\n

                      What type of Ethernet cable is traditionally required to connect two similar network devices directly, such as a switch to a switch or a router to a router?<\/b><\/p>\n

                        \n
                      1. Straight-through cable<\/span><\/li>\n
                      2. Crossover cable<\/span><\/li>\n
                      3. Rollover console cable<\/span><\/li>\n
                      4. Fiber optic patch cable<\/span><\/li>\n<\/ol>\n

                        Correct Answer: 2<\/b><\/p>\n

                        Explanation:<\/b><\/p>\n

                        An Ethernet crossover cable is a specialized twisted-pair copper cable wired with different pinout configurations at each end (specifically reversing transmit and receive pairs, utilizing T568A on one end and T568B on the other) to connect similar network devices directly together without an intervening hub or switch. Historically, straight-through cables were used for dissimilar devices (such as a workstation to a switch), while crossover cables were required for similar devices (such as switch-to-switch, router-to-router, or PC-to-PC connections) to ensure that the transmit pins on one device aligned correctly with the receive pins on the other. However, modern Cisco switches and routers universally support Auto-MDIX (Automatic Medium-Dependent Interface Crossover), a feature that automatically detects the required pinout configuration and electronically corrects mismatched cable types on the fly, eliminating the operational need for manual crossover cables in modern networking environments.<\/span><\/p>\n

                        Question 272<\/b><\/h3>\n

                        What two metrics are utilized by default to calculate the composite metric in EIGRP?<\/b><\/p>\n

                          \n
                        1. Hop count and bandwidth<\/span><\/li>\n
                        2. Bandwidth and delay<\/span><\/li>\n
                        3. Load and reliability<\/span><\/li>\n
                        4. MTU and cost<\/span><\/li>\n<\/ol>\n

                          Correct Answer: 2<\/b><\/p>\n

                          Explanation:<\/b><\/p>\n

                          The Enhanced Interior Gateway Routing Protocol (EIGRP) is an advanced distance-vector routing protocol developed by Cisco that utilizes a sophisticated composite metric to determine the optimal path to a destination network. By default, EIGRP calculates its composite metric using exactly two core parameters: bandwidth (the slowest bandwidth along the path) and delay (the cumulative interface delay along the path). While EIGRP formulas technically include variables for load and reliability, their default weighting factors are set to zero, effectively disabling them from active metric calculations unless manually modified by an administrator. This combination of bandwidth and delay allows EIGRP to accurately evaluate link capacities across heterogeneous WAN and LAN topologies, ensuring superior path selection compared to legacy routing protocols that rely solely on simple hop counts.<\/span><\/p>\n

                          Question 273<\/b><\/h3>\n

                          What UDP port is utilized by default for Network Time Protocol (NTP) communications across networks?<\/b><\/p>\n

                            \n
                          1. Port 53<\/span><\/li>\n
                          2. Port 69<\/span><\/li>\n
                          3. Port 123<\/span><\/li>\n
                          4. Port 161<\/span><\/li>\n<\/ol>\n

                            Correct Answer: 3<\/b><\/p>\n

                            Explanation:<\/b><\/p>\n

                            The Network Time Protocol operates by default over User Datagram Protocol (UDP) port 123. NTP is a critical enterprise networking protocol designed to synchronize the internal system clocks of computers, routers, switches, and firewalls across variable latency IP networks. Accurate timekeeping is vital across enterprise infrastructures because synchronized timestamps are required for correlating Syslog error messages, analyzing security audit logs, executing digital certificates, and coordinating automated scheduling tasks. By utilizing hierarchical stratum levels connected to atomic or GPS time sources, NTP ensures that network devices maintain precise time synchronization within milliseconds, preventing chronological discrepancies during incident investigation and troubleshooting.<\/span><\/p>\n

                            Question 274<\/b><\/h3>\n

                            What numerical range represents Standard IPv4 Access Control Lists in Cisco IOS?<\/b><\/p>\n

                              \n
                            1. 1 to 99<\/span><\/li>\n
                            2. 100 to 199<\/span><\/li>\n
                            3. 200 to 299<\/span><\/li>\n
                            4. 300 to 399<\/span><\/li>\n<\/ol>\n

                              Correct Answer: 1<\/b><\/p>\n

                              Explanation:<\/b><\/p>\n

                              In Cisco IOS routing architecture, Access Control Lists are categorized into standard and extended types, each identified by specific numerical ranges. Standard Access Control Lists are assigned numbers ranging from 1 to 99 (and additionally expanded ranges from 1300 to 1999). A fundamental characteristic of a standard ACL is that it filters network traffic by examining <\/span>only<\/b> the source IP address contained within the packet header. Because standard ACLs do not evaluate destination addresses, protocol types, or TCP\/UDP port numbers, they offer very limited filtering granularity. Consequently, standard ACLs should always be placed as close as possible to the destination network to prevent unintended filtering consequences, whereas extended ACLs (numbered 100 to 199) evaluate both source and destination parameters and should be placed close to the traffic source.<\/span><\/p>\n

                              Question 275<\/b><\/h3>\n

                              What is the primary operational purpose of DHCP snooping on a Cisco catalyst switch?<\/b><\/p>\n

                                \n
                              1. Encrypting DHCP lease negotiation traffic across wireless links.<\/span><\/li>\n
                              2. Preventing rogue DHCP servers from distributing unauthorized IP configuration parameters to client hosts.<\/span><\/li>\n
                              3. Automatically balancing DHCP address lease pools across multiple distribution routers.<\/span><\/li>\n
                              4. Translating private internal IP addresses into public routable addresses using port overload.<\/span><\/li>\n<\/ol>\n

                                Correct Answer: 2<\/b><\/p>\n

                                Explanation:<\/b><\/p>\n

                                DHCP snooping is a Layer 2 security feature built into Cisco Catalyst switches that acts as a firewall between untrusted host connection ports and trusted DHCP servers. In a compromised network environment, an attacker could plug an unauthorized, rogue DHCP server into a user access port and flood the local segment with malicious IP configuration parameters\u2014assigning incorrect default gateways or malicious DNS servers to launch man-in-the-middle attacks. DHCP snooping inspects incoming DHCP traffic on a per-port basis, dividing switch ports into trusted ports (connected to legitimate enterprise DHCP servers or upstream trunks) and untrusted ports (connected to end-user workstations). The switch intercepts DHCP server replies arriving on untrusted ports and drops them immediately, protecting the local network infrastructure from unauthorized address assignments and spoofing attacks.<\/span><\/p>\n

                                Question 276<\/b><\/h3>\n

                                Which Syslog severity level corresponds to an informational message that highlights normal system operations without indicating an error?<\/b><\/p>\n

                                  \n
                                1. Level 3<\/span><\/li>\n
                                2. Level 4<\/span><\/li>\n
                                3. Level 6<\/span><\/li>\n
                                4. Level 7<\/span><\/li>\n<\/ol>\n

                                  Correct Answer: 3<\/b><\/p>\n

                                  Explanation:<\/b><\/p>\n

                                  Syslog severity levels range numerically from 0 to 7, where lower numbers represent higher operational urgency and severity, and higher numbers represent lower severity notices. Level 6 corresponds to Informational messages. The complete hierarchical scale progresses from Level 0 (Emergency), Level 1 (Alert), Level 2 (Critical), Level 3 (Error), Level 4 (Warning), Level 5 (Notice), Level 6 (Informational), up to Level 7 (Debugging). Informational messages at Level 6 indicate normal, expected operational events\u2014such as an interface transitioning to an up state, a user successfully logging into the CLI, or a routing adjacency establishing successfully\u2014without requiring administrative intervention, whereas lower levels demand immediate corrective action.<\/span><\/p>\n

                                  Question 277<\/b><\/h3>\n

                                  What is the defining characteristic of a stub network in enterprise routing topologies?<\/b><\/p>\n

                                    \n
                                  1. A network segment that possesses multiple redundant exit paths to the internet core.<\/span><\/li>\n
                                  2. A network segment connected to only one router, having only a single path in and out of the area.<\/span><\/li>\n
                                  3. A wireless bridge link operating without encryption over public airwaves.<\/span><\/li>\n
                                  4. A loopback interface utilized exclusively for OSPF router ID selection.<\/span><\/li>\n<\/ol>\n

                                    Correct Answer: 2<\/b><\/p>\n

                                    Explanation:<\/b><\/p>\n

                                    A stub network is a routing domain or subnet connected to the rest of the network through a single path, meaning traffic entering or leaving the segment has only one router interface to traverse. In routing protocol designs such as OSPF, stub areas are specialized regions where routers do not receive external routing table updates from other areas. Instead, OSPF boundary routers inject a default summary route into the stub area, allowing internal routers to reach all external destinations via that single exit point without consuming memory and CPU resources storing massive global routing tables. This architectural optimization significantly improves convergence performance and resource efficiency in branch office environments.<\/span><\/p>\n

                                    Question 278<\/b><\/h3>\n

                                    At which OSI layers do traditional bridges and routers operate, respectively?<\/b><\/p>\n

                                      \n
                                    1. Bridge operates at Layer 1; Router operates at Layer 2<\/span><\/li>\n
                                    2. Bridge operates at Layer 2; Router operates at Layer 3<\/span><\/li>\n
                                    3. Bridge operates at Layer 3; Router operates at Layer 4<\/span><\/li>\n
                                    4. Bridge operates at Layer 4; Router operates at Layer 7<\/span><\/li>\n<\/ol>\n

                                      Correct Answer: 2<\/b><\/p>\n

                                      Explanation:<\/b><\/p>\n

                                      Understanding the OSI layer operation of network devices is fundamental to network engineering. Traditional network bridges and Layer 2 switches operate exclusively at Layer 2 (the Data Link layer) of the OSI reference model, making forwarding and filtering decisions based entirely on physical 48-bit MAC addresses. They forward frames within the same local network segment and do not evaluate IP addresses or route packets across different subnet boundaries. In contrast, routers operate at Layer 3 (the Network layer), utilizing logical IP addresses and routing tables to determine optimal paths, strip Layer 2 headers, and forward packets across disparate wide area networks and subnets.<\/span><\/p>\n

                                      Question 279<\/b><\/h3>\n

                                      What is the primary purpose of an IPv6 anycast address within a network topology?<\/b><\/p>\n

                                        \n
                                      1. Delivering packets to every single node simultaneously across the global internet.<\/span><\/li>\n
                                      2. Delivering packets to the nearest or most topologically efficient interface among a group of nodes sharing the same address.<\/span><\/li>\n
                                      3. Restricting packet routing strictly to the local physical link.<\/span><\/li>\n
                                      4. Encrypting payload data against unauthorized eavesdropping.<\/span><\/li>\n<\/ol>\n

                                        Correct Answer: 2<\/b><\/p>\n

                                        Explanation:<\/b><\/p>\n

                                        An IPv6 anycast address is a specialized addressing type assigned to multiple different interfaces, typically belonging to different nodes. When a packet is transmitted toward an IPv6 anycast address, routers use standard routing protocols to deliver the packet to the single closest or most topologically efficient interface\u2014measured by routing metrics\u2014from among all the nodes configured with that anycast address. Unlike multicast addresses that deliver data to every subscribed member simultaneously or unicast addresses targeting a single specific host, anycast addressing enables high-availability services such as content delivery networks, DNS root servers, and load-balanced gateway routers, where clients automatically connect to the nearest available service provider instance without manual selection.<\/span><\/p>\n

                                        Question 280<\/b><\/h3>\n

                                        Which Cisco IOS command displays the active routing table, including directly connected networks, static routes, and dynamically learned routes?<\/b><\/p>\n

                                          \n
                                        1. show running-config<\/span><\/li>\n
                                        2. show ip interface brief<\/span><\/li>\n
                                        3. show ip route<\/span><\/li>\n
                                        4. show version<\/span><\/li>\n<\/ol>\n

                                          Correct Answer: 3<\/b><\/p>\n

                                          Explanation:<\/b><\/p>\n

                                          The show ip route command is one of the most frequently executed diagnostic commands in the Cisco IOS command-line interface when operating in privileged EXEC mode. When invoked, it displays the router’s complete active Layer 3 routing table. The output details destination subnet prefixes, administrative distances, metric values, next-hop IP addresses, exit physical interfaces, and routing source codes (such as C for connected, S for static, O for OSPF, and D for EIGRP). Network administrators rely heavily on this command to verify route propagation, confirm that static and dynamic routing protocols are populating paths correctly, and troubleshoot packet delivery failures across enterprise internetworks.<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"

                                          View Full Cisco 100-150 Exam Dumps and Practice Test Dumps.   Question 261 What is the default OSPF hello packet interval timer on multi-access broadcast networks, such as Ethernet? 5 seconds 10 seconds 30 seconds 60 seconds Correct Answer: 2 Explanation: The Open Shortest Path First routing protocol utilizes Hello packets to discover neighboring routers, […]<\/p>\n","protected":false},"author":1,"featured_media":0,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":[],"categories":[1648,1647],"tags":[],"_links":{"self":[{"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/posts\/14548"}],"collection":[{"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/comments?post=14548"}],"version-history":[{"count":1,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/posts\/14548\/revisions"}],"predecessor-version":[{"id":14569,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/posts\/14548\/revisions\/14569"}],"wp:attachment":[{"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/media?parent=14548"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/categories?post=14548"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.examlabs.com\/certification\/wp-json\/wp\/v2\/tags?post=14548"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}