Pass Fortinet NSE5_SSE_AD-7.6 Exam in First Attempt Easily
Real Fortinet NSE5_SSE_AD-7.6 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

NSE5_SSE_AD-7.6 Premium File

  • 54 Questions & Answers
  • Last Update: Nov 5, 2026
$69.99 $76.99

Fortinet NSE 5 - FortiSASE and SD-WAN 7.6 Core Administrator NSE5_SSE_AD-7.6 Practice Test 13

Question 120

A support analyst is collecting data for this scenario. A named cloud health-check target changes address, but a FortiGate with stale DNS cannot resolve it and all internet members show failed probes. Which diagnostic check is most targeted?

  1. Inspect probe source interface, route lookup to the target and health-check replies.
  2. Inspect probe target route, packet capture and health status during an upstream outage.
  3. Review DNS server config, name lookup, probe logs and route response.
  4. Compare measurement mode, probe frequency, traffic volume and last update time.

Explanation

Correct Answer

C:

Review DNS server config, name lookup, probe logs and route response. This inspection targets SLA probe blackhole after DNS failure rather than a different configuration issue. The corrective action is: Restore supported FortiGate DNS reachability or use a suitable stable probe target, then verify health checks. Expected evidence: Target resolution succeeds and viable members return to their intended health states.

Incorrect Answers

A:

Inspect probe source interface, route lookup to the target and health-check replies. This is useful when diagnosing Health-check server behind wrong route, but not the best first investigation here. Instead, review dns server config, name lookup, probe logs and route response.

B:

Inspect probe target route, packet capture and health status during an upstream outage. This is useful when diagnosing Wrong performance SLA probe destination, but not the best first investigation here. Instead, review dns server config, name lookup, probe logs and route response.

D:

Compare measurement mode, probe frequency, traffic volume and last update time. This is useful when diagnosing SLA logging gaps after passive mode change, but not the best first investigation here. Instead, review dns server config, name lookup, probe logs and route response.

Question 121

A Fortinet administrator must address this operational problem. An SD-WAN rule requires two links to satisfy SLA but only one remains available, so the special service stops steering as expected. Which response best resolves it?

  1. Restore supported FortiGate DNS reachability or use a suitable stable probe target, then verify health checks.
  2. Calibrate thresholds to application tolerance and real path baseline instead of arbitrary low figures.
  3. Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement.
  4. Choose a target reachable by each member or correct the per-member probe route for the intended endpoint.

Explanation

Correct Answer

C:

Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement. The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect. Expected evidence: With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition. Key limit: Reducing the minimum cannot make an unhealthy member satisfy the objective.

Incorrect Answers

A:

Restore supported FortiGate DNS reachability or use a suitable stable probe target, then verify health checks. This could apply to the separate issue SLA probe blackhole after DNS failure: A named cloud health-check target changes address, but a FortiGate with stale DNS cannot resolve it and all internet members show failed probes. For Minimum members meeting SLA, the directly relevant action is: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement.

B:

Calibrate thresholds to application tolerance and real path baseline instead of arbitrary low figures. This could apply to the separate issue SLA latency threshold too strict: A regional fiber link normally measures 35 ms but an engineer sets a 10 ms latency requirement, making all members appear below target. For Minimum members meeting SLA, the directly relevant action is: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement.

D:

Choose a target reachable by each member or correct the per-member probe route for the intended endpoint. This could apply to the separate issue Health-check server behind wrong route: A performance SLA for a backup carrier uses a server reachable only through the primary carrier, so backup checks fail despite working general internet reachability. For Minimum members meeting SLA, the directly relevant action is: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement.

Question 122

For this situation, a reviewer needs acceptance evidence. An SD-WAN rule requires two links to satisfy SLA but only one remains available, so the special service stops steering as expected. Which result most directly demonstrates success?

  1. When both links satisfy SLA, new matching sessions select the lower-cost approved path.
  2. Target resolution succeeds and viable members return to their intended health states.
  3. Normally healthy paths satisfy the chosen target, while injected excessive delay still causes intended steering.
  4. With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition.

Explanation

Correct Answer

D:

With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition. This is the directly relevant check for Minimum members meeting SLA. It confirms the required step: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement. The operating principle is: The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.

Incorrect Answers

A:

When both links satisfy SLA, new matching sessions select the lower-cost approved path. This would validate a different scenario, Wrong SD-WAN member cost expectation, where A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. The current case needs evidence for Minimum members meeting SLA.

B:

Target resolution succeeds and viable members return to their intended health states. This would validate a different scenario, SLA probe blackhole after DNS failure, where A named cloud health-check target changes address, but a FortiGate with stale DNS cannot resolve it and all internet members show failed probes. The current case needs evidence for Minimum members meeting SLA.

C:

Normally healthy paths satisfy the chosen target, while injected excessive delay still causes intended steering. This would validate a different scenario, SLA latency threshold too strict, where A regional fiber link normally measures 35 ms but an engineer sets a 10 ms latency requirement, making all members appear below target. The current case needs evidence for Minimum members meeting SLA.

Question 123

A network administrator must explain the underlying control. An SD-WAN rule requires two links to satisfy SLA but only one remains available, so the special service stops steering as expected. Which statement is correct?

  1. Active SLA quality depends on probes traversing the member whose health is being measured.
  2. SLA DNS-name probes depend on the firewall resolving the configured target as well as transporting packets.
  3. The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.
  4. Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.

Explanation

Correct Answer

C:

The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect. This explains Minimum members meeting SLA in the given environment. The implementation decision is: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement. Confirm it with: With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition.

Incorrect Answers

A:

Active SLA quality depends on probes traversing the member whose health is being measured. That concept concerns Health-check server behind wrong route, not the mechanism needed for Minimum members meeting SLA. The relevant principle is: The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.

B:

SLA DNS-name probes depend on the firewall resolving the configured target as well as transporting packets. That concept concerns SLA probe blackhole after DNS failure, not the mechanism needed for Minimum members meeting SLA. The relevant principle is: The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.

D:

Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate. That concept concerns Wrong SD-WAN member cost expectation, not the mechanism needed for Minimum members meeting SLA. The relevant principle is: The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.

Question 124

An incident team needs to isolate the root cause. An SD-WAN rule requires two links to satisfy SLA but only one remains available, so the special service stops steering as expected. Which investigation should be prioritized?

  1. Inspect historical latency trends, threshold, service results and route decisions.
  2. Inspect probe source interface, route lookup to the target and health-check replies.
  3. Inspect configured minimum, member SLA map and matched SD-WAN service status.
  4. Review DNS server config, name lookup, probe logs and route response.

Explanation

Correct Answer

C:

Inspect configured minimum, member SLA map and matched SD-WAN service status. This inspection targets Minimum members meeting SLA rather than a different configuration issue. The corrective action is: Review the minimum-SLA-meet-members setting against desired resilience and configure it to the justified requirement. Expected evidence: With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition.

Incorrect Answers

A:

Inspect historical latency trends, threshold, service results and route decisions. This is useful when diagnosing SLA latency threshold too strict. Instead, inspect configured minimum, member sla map and matched sd-wan service status.

B:

Inspect probe source interface, route lookup to the target and health-check replies. This is useful when diagnosing Health-check server behind wrong route. Instead, inspect configured minimum, member sla map and matched sd-wan service status.

D:

Review DNS server config, name lookup, probe logs and route response. This is useful when diagnosing SLA probe blackhole after DNS failure. Instead, inspect configured minimum, member sla map and matched sd-wan service status.

Question 125

A network engineer faces the following FortiSASE or SD-WAN condition. An alert announces rising delay on a WAN, and staff assume every existing session will instantly move to the other ISP. What should the engineer do?

  1. Use an appropriately configured active probe when continuous idle-link measurement is required, or generate controlled representative traffic.
  2. Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets.
  3. Choose a target reachable by each member or correct the per-member probe route for the intended endpoint.
  4. Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover.

Explanation

Correct Answer

D:

Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover. SD-WAN SLA status and session-table stickiness influence which connections change path after degradation. Expected evidence: A controlled new flow follows the policy while long-lived session behavior is recorded separately. Key limit: SLA path changes do not guarantee stateful existing sessions survive a carrier switch.

Incorrect Answers

A:

Use an appropriately configured active probe when continuous idle-link measurement is required, or generate controlled representative traffic. This could apply to the separate issue Passive health measurement idle link: A newly commissioned backup WAN reports little passive quality data because hardly any user sessions have used it. For SLA alarm not equivalent to route withdrawal, the directly relevant action is: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover.

B:

Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets. This could apply to the separate issue Lowest cost in-SLA selection: A less expensive backup link and a costly premium link both pass voice SLA, but the engineer wants the cheaper path while maintaining quality. For SLA alarm not equivalent to route withdrawal, the directly relevant action is: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover.

C:

Choose a target reachable by each member or correct the per-member probe route for the intended endpoint. This could apply to the separate issue Health-check server behind wrong route: A performance SLA for a backup carrier uses a server reachable only through the primary carrier, so backup checks fail despite working general internet reachability. For SLA alarm not equivalent to route withdrawal, the directly relevant action is: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover.

Question 126

A pilot is validating the implementation. An alert announces rising delay on a WAN, and staff assume every existing session will instantly move to the other ISP. Which finding proves that the intended fix works?

  1. With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition.
  2. A controlled new flow follows the policy while long-lived session behavior is recorded separately.
  3. Each member independently reaches its designated health target and reports meaningful path status.
  4. With upstream connectivity withdrawn, the relevant member becomes unhealthy despite its physical link remaining up.

Explanation

Correct Answer

B:

A controlled new flow follows the policy while long-lived session behavior is recorded separately. This is the directly relevant check for SLA alarm not equivalent to route withdrawal. It confirms the required step: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover. The operating principle is: SD-WAN SLA status and session-table stickiness influence which connections change path after degradation.

Incorrect Answers

A:

With one in-SLA link, the rule behaves according to the approved minimum rather than silently failing its eligibility condition. This would validate a different scenario, Minimum members meeting SLA, where An SD-WAN rule requires two links to satisfy SLA but only one remains available, so the special service stops steering as expected. The current case needs evidence for SLA alarm not equivalent to route withdrawal.

C:

Each member independently reaches its designated health target and reports meaningful path status. This would validate a different scenario, Health-check server behind wrong route, where A performance SLA for a backup carrier uses a server reachable only through the primary carrier, so backup checks fail despite working general internet reachability. The current case needs evidence for SLA alarm not equivalent to route withdrawal.

D:

With upstream connectivity withdrawn, the relevant member becomes unhealthy despite its physical link remaining up. This would validate a different scenario, Wrong performance SLA probe destination, where A branch's SLA probes a server inside its own LAN and reports both carriers healthy even during an upstream internet outage. The current case needs evidence for SLA alarm not equivalent to route withdrawal.

Question 127

A technical lead asks why the recommended approach works. An alert announces rising delay on a WAN, and staff assume every existing session will instantly move to the other ISP. Which mechanism is most relevant?

  1. SD-WAN SLA status and session-table stickiness influence which connections change path after degradation.
  2. Active SLA quality depends on probes traversing the member whose health is being measured.
  3. Active probes provide periodic measurements independently of user-session sample availability.
  4. The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect.

Explanation

Correct Answer

A:

SD-WAN SLA status and session-table stickiness influence which connections change path after degradation. This explains SLA alarm not equivalent to route withdrawal in the given environment. The implementation decision is: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover. Confirm it with: A controlled new flow follows the policy while long-lived session behavior is recorded separately.

Incorrect Answers

B:

Active SLA quality depends on probes traversing the member whose health is being measured. That concept concerns Health-check server behind wrong route, not the mechanism needed for SLA alarm not equivalent to route withdrawal. The relevant principle is: SD-WAN SLA status and session-table stickiness influence which connections change path after degradation.

C:

Active probes provide periodic measurements independently of user-session sample availability. That concept concerns SLA logging gaps after passive mode change, not the mechanism needed for SLA alarm not equivalent to route withdrawal. The relevant principle is: SD-WAN SLA status and session-table stickiness influence which connections change path after degradation.

D:

The configured minimum determines how many eligible members are needed before the SLA-based rule takes effect. That concept concerns Minimum members meeting SLA, not the mechanism needed for SLA alarm not equivalent to route withdrawal. The relevant principle is: SD-WAN SLA status and session-table stickiness influence which connections change path after degradation.

Question 128

Before changing production settings, an engineer reviews the symptoms. An alert announces rising delay on a WAN, and staff assume every existing session will instantly move to the other ISP. Which evidence is most useful?

  1. Review SLA event, service table, session flags and packet path across an induced fault.
  2. Inspect member cost, priority, health-check status and rule's selected member.
  3. Inspect probe source interface, route lookup to the target and health-check replies.
  4. Inspect per-member loss counters, probes, rule health map and session selection.

Explanation

Correct Answer

A:

Review SLA event, service table, session flags and packet path across an induced fault. This inspection targets SLA alarm not equivalent to route withdrawal rather than a different configuration issue. The corrective action is: Check SLA state, selected strategy and new-session versus existing-session behavior before asserting a complete cutover. Expected evidence: A controlled new flow follows the policy while long-lived session behavior is recorded separately.

Incorrect Answers

B:

Inspect member cost, priority, health-check status and rule's selected member. This is useful when diagnosing Lowest cost in-SLA selection, but not the best first investigation here. Instead, review sla event, service table, session flags and packet path across an induced fault.

C:

Inspect probe source interface, route lookup to the target and health-check replies. This is useful when diagnosing Health-check server behind wrong route, but not the best first investigation here. Instead, review sla event, service table, session flags and packet path across an induced fault.

D:

Inspect per-member loss counters, probes, rule health map and session selection. This is useful when diagnosing Loss-driven link failover, but not the best first investigation here. Instead, review sla event, service table, session flags and packet path across an induced fault.

Question 129

A deployment review finds this gap. A less expensive backup link and a costly premium link both pass voice SLA, but the engineer wants the cheaper path while maintaining quality. What is the most targeted next configuration step?

  1. Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets.
  2. Use an appropriately configured active probe when continuous idle-link measurement is required, or generate controlled representative traffic.
  3. Create a voice-appropriate performance SLA measuring jitter, latency and loss and reference it in the matching SD-WAN rule.
  4. Apply a best-quality strategy with a relevant performance SLA measurement and suitable application match.

Explanation

Correct Answer

A:

Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets. Lowest Cost (SLA) selects low-cost eligible links after evaluating monitored service constraints. Expected evidence: Both links in SLA lead new traffic to the cheaper member; degrading the cheaper path causes a healthy alternate to be selected. Key limit: If no link meets target, the platform's configured fallback behavior still needs testing.

Incorrect Answers

B:

Use an appropriately configured active probe when continuous idle-link measurement is required, or generate controlled representative traffic. This could apply to the separate issue Passive health measurement idle link: A newly commissioned backup WAN reports little passive quality data because hardly any user sessions have used it. For Lowest cost in-SLA selection, the directly relevant action is: Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets.

C:

Create a voice-appropriate performance SLA measuring jitter, latency and loss and reference it in the matching SD-WAN rule. This could apply to the separate issue VoIP jitter performance SLA: The primary ISP has low packet loss but occasional severe jitter, and voice calls degrade while a backup link is stable. For Lowest cost in-SLA selection, the directly relevant action is: Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets.

D:

Apply a best-quality strategy with a relevant performance SLA measurement and suitable application match. This could apply to the separate issue Best-quality strategy for video meetings: A branch has two similarly priced carriers but video jitter differs each hour and policy owners want selection based on measured quality rather than cost. For Lowest cost in-SLA selection, the directly relevant action is: Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets.

Question 130

The recommended change has been applied. A less expensive backup link and a costly premium link both pass voice SLA, but the engineer wants the cheaper path while maintaining quality. Which observation best verifies the intended outcome?

  1. A controlled jitter increase makes new eligible voice sessions favor the in-SLA backup path.
  2. The backup link shows ongoing measurements before production traffic is shifted.
  3. Both links in SLA lead new traffic to the cheaper member; degrading the cheaper path causes a healthy alternate to be selected.
  4. New conferencing sessions favor the measured higher-quality eligible path during test intervals.

Explanation

Correct Answer

C:

Both links in SLA lead new traffic to the cheaper member; degrading the cheaper path causes a healthy alternate to be selected. This is the directly relevant check for Lowest cost in-SLA selection. It confirms the required step: Use Lowest Cost (SLA) with reviewed per-member costs and the required jitter/latency targets. The operating principle is: Lowest Cost (SLA) selects low-cost eligible links after evaluating monitored service constraints.

Incorrect Answers

A:

A controlled jitter increase makes new eligible voice sessions favor the in-SLA backup path. This would validate a different scenario, VoIP jitter performance SLA, where The primary ISP has low packet loss but occasional severe jitter, and voice calls degrade while a backup link is stable. The current case needs evidence for Lowest cost in-SLA selection.

B:

The backup link shows ongoing measurements before production traffic is shifted. This would validate a different scenario, Passive health measurement idle link, where A newly commissioned backup WAN reports little passive quality data because hardly any user sessions have used it. The current case needs evidence for Lowest cost in-SLA selection.

D:

New conferencing sessions favor the measured higher-quality eligible path during test intervals. This would validate a different scenario, Best-quality strategy for video meetings, where A branch has two similarly priced carriers but video jitter differs each hour and policy owners want selection based on measured quality rather than cost. The current case needs evidence for Lowest cost in-SLA selection.

Fortinet NSE 5 - FortiSASE and SD-WAN 7.6 Core Administrator (NSE5_SSE_AD-7.6) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports