Pass Fortinet NSE5_SSE_AD-7.6 Exam in First Attempt Easily
Real Fortinet NSE5_SSE_AD-7.6 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

NSE5_SSE_AD-7.6 Premium File

  • 54 Questions & Answers
  • Last Update: Nov 5, 2026
$69.99 $76.99

Fortinet NSE 5 - FortiSASE and SD-WAN 7.6 Core Administrator NSE5_SSE_AD-7.6 Practice Test 8

Question 70

The recommended change has been applied. A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. Which observation best verifies the intended outcome?

  1. Only authorized emergency flows use the LTE member and regular browsing stays on other links.
  2. The backup link shows ongoing measurements before production traffic is shifted.
  3. When both links satisfy SLA, new matching sessions select the lower-cost approved path.
  4. The health probe reaches the intended target with an accepted source address on each link.

Explanation

Correct Answer

C:

When both links satisfy SLA, new matching sessions select the lower-cost approved path. This is the directly relevant check for Wrong SD-WAN member cost expectation. It confirms the required step: Set reviewed member costs and eligible interface preference to express the intended price ordering. The operating principle is: Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.

Incorrect Answers

A:

Only authorized emergency flows use the LTE member and regular browsing stays on other links. This would validate a different scenario, Single-member zone for special transport, where A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. The current case needs evidence for Wrong SD-WAN member cost expectation.

B:

The backup link shows ongoing measurements before production traffic is shifted. This would validate a different scenario, Passive health measurement idle link, where A newly commissioned backup WAN reports little passive quality data because hardly any user sessions have used it. The current case needs evidence for Wrong SD-WAN member cost expectation.

D:

The health probe reaches the intended target with an accepted source address on each link. This would validate a different scenario, Member routing source interface ambiguity, where Two WAN members have equally reachable upstream gateways, but remote monitoring probes use an unexpected source and are filtered by an ISP. The current case needs evidence for Wrong SD-WAN member cost expectation.

Question 71

An architect reviews the platform behavior behind this incident. A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. Which explanation applies?

  1. Passive WAN health derives measurements from eligible observed sessions; active health checks generate probes independently.
  2. Member interface source selection can affect locally originated monitoring even when forwarded user sessions work.
  3. Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.
  4. A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.

Explanation

Correct Answer

C:

Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate. This explains Wrong SD-WAN member cost expectation in the given environment. The implementation decision is: Set reviewed member costs and eligible interface preference to express the intended price ordering. Confirm it with: When both links satisfy SLA, new matching sessions select the lower-cost approved path.

Incorrect Answers

A:

Passive WAN health derives measurements from eligible observed sessions; active health checks generate probes independently. That concept concerns Passive health measurement idle link, not the mechanism needed for Wrong SD-WAN member cost expectation. The relevant principle is: Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.

B:

Member interface source selection can affect locally originated monitoring even when forwarded user sessions work. That concept concerns Member routing source interface ambiguity, not the mechanism needed for Wrong SD-WAN member cost expectation. The relevant principle is: Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.

D:

A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it. That concept concerns Single-member zone for special transport, not the mechanism needed for Wrong SD-WAN member cost expectation. The relevant principle is: Lowest Cost (SLA) considers qualifying links' configured costs before choosing the preferred candidate.

Question 72

A support analyst is collecting data for this scenario. A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. Which diagnostic check is most targeted?

  1. Review health-check method, session sample volume and link measurement timestamps.
  2. Inspect member source-IP configuration, packet capture, ISP ACL and probe response.
  3. Inspect member cost, matching service mode, SLA status and selected member.
  4. Inspect zone membership, eligible services, policy references and LTE session count.

Explanation

Correct Answer

C:

Inspect member cost, matching service mode, SLA status and selected member. This inspection targets Wrong SD-WAN member cost expectation rather than a different configuration issue. The corrective action is: Set reviewed member costs and eligible interface preference to express the intended price ordering. Expected evidence: When both links satisfy SLA, new matching sessions select the lower-cost approved path.

Incorrect Answers

A:

Review health-check method, session sample volume and link measurement timestamps. This is useful when diagnosing Passive health measurement idle link. Instead, inspect member cost, matching service mode, sla status and selected member.

B:

Inspect member source-IP configuration, packet capture, ISP ACL and probe response. This is useful when diagnosing Member routing source interface ambiguity. Instead, inspect member cost, matching service mode, sla status and selected member.

D:

Inspect zone membership, eligible services, policy references and LTE session count. This is useful when diagnosing Single-member zone for special transport. Instead, inspect member cost, matching service mode, sla status and selected member.

Question 73

A Fortinet administrator must address this operational problem. An engineer sees traffic egress from a numbered SD-WAN member but cannot tell which IPsec tunnel underlay provides that member's path. Which response best resolves it?

  1. Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association.
  2. Add supported IPsec tunnel interfaces as SD-WAN members in an overlay zone with intended routes and health checks.
  3. Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it.
  4. Plan the authorized member-zone reassignment and update dependent route and firewall-zone rules coherently.

Explanation

Correct Answer

A:

Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association. SD-WAN diagnostics identify selected members independently of their human-friendly link names. Expected evidence: The selected service and member ID resolve to the expected tunnel interface and underlay path. Key limit: The member ID by itself does not prove the remote tunnel endpoint is reachable.

Incorrect Answers

B:

Add supported IPsec tunnel interfaces as SD-WAN members in an overlay zone with intended routes and health checks. This could apply to the separate issue IPsec overlay member zone: A regional hub has two IPsec tunnels to the same branch, but private-app failover is not coordinated because the tunnels are absent from the overlay SD-WAN design. For Overlay member versus physical port logging, the directly relevant action is: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association.

C:

Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it. This could apply to the separate issue Single-member zone for special transport: A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. For Overlay member versus physical port logging, the directly relevant action is: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association.

D:

Plan the authorized member-zone reassignment and update dependent route and firewall-zone rules coherently. This could apply to the separate issue Moving a member between zones: A branch wants to repurpose its second internet interface for private overlay-only traffic while policies still target its original public zone. For Overlay member versus physical port logging, the directly relevant action is: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association.

Question 74

For this situation, a reviewer needs acceptance evidence. An engineer sees traffic egress from a numbered SD-WAN member but cannot tell which IPsec tunnel underlay provides that member's path. Which result most directly demonstrates success?

  1. Public internet flows no longer select the repurposed member and approved overlay traffic behaves as designed.
  2. Private connections select a healthy authorized tunnel and have the intended secondary path on failure.
  3. The member appears only in the intended logical zone and test policies match that zone.
  4. The selected service and member ID resolve to the expected tunnel interface and underlay path.

Explanation

Correct Answer

D:

The selected service and member ID resolve to the expected tunnel interface and underlay path. This is the directly relevant check for Overlay member versus physical port logging. It confirms the required step: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association. The operating principle is: SD-WAN diagnostics identify selected members independently of their human-friendly link names.

Incorrect Answers

A:

Public internet flows no longer select the repurposed member and approved overlay traffic behaves as designed. This would validate a different scenario, Moving a member between zones, where A branch wants to repurpose its second internet interface for private overlay-only traffic while policies still target its original public zone. The current case needs evidence for Overlay member versus physical port logging.

B:

Private connections select a healthy authorized tunnel and have the intended secondary path on failure. This would validate a different scenario, IPsec overlay member zone, where A regional hub has two IPsec tunnels to the same branch, but private-app failover is not coordinated because the tunnels are absent from the overlay SD-WAN design. The current case needs evidence for Overlay member versus physical port logging.

C:

The member appears only in the intended logical zone and test policies match that zone. This would validate a different scenario, WAN member default-zone misconception, where An administrator adds a new Ethernet WAN member without explicitly choosing a custom zone and assumes it is isolated from the existing internet policy. The current case needs evidence for Overlay member versus physical port logging.

Question 75

A network administrator must explain the underlying control. An engineer sees traffic egress from a numbered SD-WAN member but cannot tell which IPsec tunnel underlay provides that member's path. Which statement is correct?

  1. Absent an explicit custom selection, an enrolled member may join the default SD-WAN zone.
  2. FortiOS can treat eligible IPsec interfaces as SD-WAN members alongside physical underlays.
  3. SD-WAN diagnostics identify selected members independently of their human-friendly link names.
  4. Changing zone membership alters which policies and route groups can reference the member.

Explanation

Correct Answer

C:

SD-WAN diagnostics identify selected members independently of their human-friendly link names. This explains Overlay member versus physical port logging in the given environment. The implementation decision is: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association. Confirm it with: The selected service and member ID resolve to the expected tunnel interface and underlay path.

Incorrect Answers

A:

Absent an explicit custom selection, an enrolled member may join the default SD-WAN zone. That concept concerns WAN member default-zone misconception, not the mechanism needed for Overlay member versus physical port logging. The relevant principle is: SD-WAN diagnostics identify selected members independently of their human-friendly link names.

B:

FortiOS can treat eligible IPsec interfaces as SD-WAN members alongside physical underlays. That concept concerns IPsec overlay member zone, not the mechanism needed for Overlay member versus physical port logging. The relevant principle is: SD-WAN diagnostics identify selected members independently of their human-friendly link names.

D:

Changing zone membership alters which policies and route groups can reference the member. That concept concerns Moving a member between zones, not the mechanism needed for Overlay member versus physical port logging. The relevant principle is: SD-WAN diagnostics identify selected members independently of their human-friendly link names.

Question 76

An incident team needs to isolate the root cause. An engineer sees traffic egress from a numbered SD-WAN member but cannot tell which IPsec tunnel underlay provides that member's path. Which investigation should be prioritized?

  1. Inspect member sequence ID, interface binding, tunnel monitor and session output.
  2. Inspect tunnel interface state, member association, overlay routing and actual session path.
  3. Inspect zone membership, eligible services, policy references and LTE session count.
  4. Inspect default-zone member list, service rules and effective firewall policies.

Explanation

Correct Answer

A:

Inspect member sequence ID, interface binding, tunnel monitor and session output. This inspection targets Overlay member versus physical port logging rather than a different configuration issue. The corrective action is: Map the session's SD-WAN member identifier back to its configured interface and overlay tunnel association. Expected evidence: The selected service and member ID resolve to the expected tunnel interface and underlay path.

Incorrect Answers

B:

Inspect tunnel interface state, member association, overlay routing and actual session path. This is useful when diagnosing IPsec overlay member zone. Instead, inspect member sequence id, interface binding, tunnel monitor and session output.

C:

Inspect zone membership, eligible services, policy references and LTE session count. This is useful when diagnosing Single-member zone for special transport. Instead, inspect member sequence id, interface binding, tunnel monitor and session output.

D:

Inspect default-zone member list, service rules and effective firewall policies. This is useful when diagnosing WAN member default-zone misconception. Instead, inspect member sequence id, interface binding, tunnel monitor and session output.

Question 77

A network engineer faces the following FortiSASE or SD-WAN condition. A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. What should the engineer do?

  1. Add supported IPsec tunnel interfaces as SD-WAN members in an overlay zone with intended routes and health checks.
  2. Reference the corresponding SD-WAN zone in the matching firewall policy and leave per-member steering to SD-WAN rules.
  3. Set reviewed member costs and eligible interface preference to express the intended price ordering.
  4. Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it.

Explanation

Correct Answer

D:

Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it. A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it. Expected evidence: Only authorized emergency flows use the LTE member and regular browsing stays on other links. Key limit: A single-member zone cannot provide intra-zone redundancy by itself.

Incorrect Answers

A:

Add supported IPsec tunnel interfaces as SD-WAN members in an overlay zone with intended routes and health checks. This could apply to the separate issue IPsec overlay member zone: A regional hub has two IPsec tunnels to the same branch, but private-app failover is not coordinated because the tunnels are absent from the overlay SD-WAN design. For Single-member zone for special transport, the directly relevant action is: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it.

B:

Reference the corresponding SD-WAN zone in the matching firewall policy and leave per-member steering to SD-WAN rules. This could apply to the separate issue Firewall policy and SD-WAN zone name: Two physical WAN ports become members of an SD-WAN zone but a newly created policy insists on specifying each member separately. For Single-member zone for special transport, the directly relevant action is: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it.

C:

Set reviewed member costs and eligible interface preference to express the intended price ordering. This could apply to the separate issue Wrong SD-WAN member cost expectation: A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. For Single-member zone for special transport, the directly relevant action is: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it.

Question 78

A pilot is validating the implementation. A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. Which finding proves that the intended fix works?

  1. Private connections select a healthy authorized tunnel and have the intended secondary path on failure.
  2. Only authorized emergency flows use the LTE member and regular browsing stays on other links.
  3. When both links satisfy SLA, new matching sessions select the lower-cost approved path.
  4. Public user traffic cannot choose the partner-only link while permitted partner flows retain reachability.

Explanation

Correct Answer

B:

Only authorized emergency flows use the LTE member and regular browsing stays on other links. This is the directly relevant check for Single-member zone for special transport. It confirms the required step: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it. The operating principle is: A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.

Incorrect Answers

A:

Private connections select a healthy authorized tunnel and have the intended secondary path on failure. This would validate a different scenario, IPsec overlay member zone, where A regional hub has two IPsec tunnels to the same branch, but private-app failover is not coordinated because the tunnels are absent from the overlay SD-WAN design. The current case needs evidence for Single-member zone for special transport.

C:

When both links satisfy SLA, new matching sessions select the lower-cost approved path. This would validate a different scenario, Wrong SD-WAN member cost expectation, where A help desk expects the cheap metered backup link to be idle, but both links have identical cost under a Lowest Cost (SLA) rule. The current case needs evidence for Single-member zone for special transport.

D:

Public user traffic cannot choose the partner-only link while permitted partner flows retain reachability. This would validate a different scenario, Mixed purpose underlay separation, where A company has one commercial internet carrier and one regulated partner transport, yet both are placed in a shared underlay zone used by a general browsing policy. The current case needs evidence for Single-member zone for special transport.

Question 79

A technical lead asks why the recommended approach works. A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. Which mechanism is most relevant?

  1. Zone segmentation constrains which member families may participate in routes and policies.
  2. A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.
  3. Absent an explicit custom selection, an enrolled member may join the default SD-WAN zone.
  4. FortiOS can treat eligible IPsec interfaces as SD-WAN members alongside physical underlays.

Explanation

Correct Answer

B:

A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it. This explains Single-member zone for special transport in the given environment. The implementation decision is: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it. Confirm it with: Only authorized emergency flows use the LTE member and regular browsing stays on other links.

Incorrect Answers

A:

Zone segmentation constrains which member families may participate in routes and policies. That concept concerns Mixed purpose underlay separation, not the mechanism needed for Single-member zone for special transport. The relevant principle is: A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.

C:

Absent an explicit custom selection, an enrolled member may join the default SD-WAN zone. That concept concerns WAN member default-zone misconception, not the mechanism needed for Single-member zone for special transport. The relevant principle is: A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.

D:

FortiOS can treat eligible IPsec interfaces as SD-WAN members alongside physical underlays. That concept concerns IPsec overlay member zone, not the mechanism needed for Single-member zone for special transport. The relevant principle is: A FortiOS SD-WAN zone can contain one member when isolation or policy scope requires it.

Question 80

Before changing production settings, an engineer reviews the symptoms. A healthcare branch needs one highly restricted LTE backup link excluded from routine web browsing but engineers believe every SD-WAN zone needs at least two members. Which evidence is most useful?

  1. Inspect tunnel interface state, member association, overlay routing and actual session path.
  2. Inspect member zone, matching policy destination, routing and selected member for each test.
  3. Inspect zone membership, eligible services, policy references and LTE session count.
  4. Inspect the member-to-zone mapping and the effective inbound and outbound policy interfaces.

Explanation

Correct Answer

C:

Inspect zone membership, eligible services, policy references and LTE session count. This inspection targets Single-member zone for special transport rather than a different configuration issue. The corrective action is: Create a separate legitimate SD-WAN zone containing the one LTE member and scope only emergency routes and policies to it. Expected evidence: Only authorized emergency flows use the LTE member and regular browsing stays on other links.

Incorrect Answers

A:

Inspect tunnel interface state, member association, overlay routing and actual session path. This is useful when diagnosing IPsec overlay member zone. Instead, inspect zone membership, eligible services, policy references and lte session count.

B:

Inspect member zone, matching policy destination, routing and selected member for each test. This is useful when diagnosing Mixed purpose underlay separation. Instead, inspect zone membership, eligible services, policy references and lte session count.

D:

Inspect the member-to-zone mapping and the effective inbound and outbound policy interfaces. This is useful when diagnosing Firewall policy and SD-WAN zone name. Instead, inspect zone membership, eligible services, policy references and lte session count.

Fortinet NSE 5 - FortiSASE and SD-WAN 7.6 Core Administrator (NSE5_SSE_AD-7.6) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports