Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 3

Question 20

During provider troubleshooting at Oakbend Education, this symptom is observed: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. Which targeted inspection should precede remediation?

  1. Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.
  2. Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.
  3. Inspect the precise prefix in the routing table and the resolved next-hop/forwarding entry, then compare the active static configuration with the working topology.
  4. Use `show route <prefix> extensive` to compare both candidate route sources, preference values and active/inactive reasons.

Correct answer: B

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. Instead inspect: Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.

B.

Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries. The critical distinction is aggregation and contribution of actual routed specifics, not interface bundling or BGP multipath forwarding.

C.

This check may help with another root cause, for example: A service edge was renumbered and its manually configured static next hop still points to the former address, blackholing one customer subnet despite healthy dynamic adjacencies. It does not test the first failed condition; start with: Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.

D.

That evidence could be normal while the reported defect persists. It is aimed at: A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. Instead inspect: Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.

Question 21

A production change request at Stonebridge Hospitality includes this finding: An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. What should the engineer change to address it?

  1. Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.
  2. Apply the correct RIB group and route import policy at the route source to import only the intended routes into the secondary RIB.
  3. Place customer interfaces and their routing policy in the intended separate routing instance, and validate lookups in that instance's RIB.
  4. Select and document the intended discard versus reject next-hop behavior on the protective route, while preserving active more-specific routes for legitimate destinations.

Correct answer: A

Explanation of each choice

A.

Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default. The case-specific reason is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition. A direct acceptance test is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

B.

This action may apply to a different problem, for example: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. It does not repair the stated failure boundary. The case-specific reason is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

C.

The other action is relevant when Two wholesale customers use overlapping IPv4 ranges and route lookups occur in the default table, causing one tenant's prefix to shadow the other's. The current case instead requires: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default. The distinction is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

D.

That would address a separate configuration fault: An operations runbook treats discard and reject forwarding actions as interchangeable and fails to explain the expected behavior for unmatched packets. This stem identifies a different cause, corrected by: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

Question 22

After Stonebridge Hospitality applies its proposed fix to this problem — An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. — which observation best proves the specific failure has been resolved?

  1. The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.
  2. The active route for the exact prefix uses the intended source with the expected lower Junos preference and corresponding forwarding next hop.
  3. Approved routes appear in both the source and destination RIBs with appropriate next-hop resolution, while unrelated tenant routes remain excluded.
  4. Each tenant prefix is present in its own instance-specific routing table and traffic exits through that tenant's correct interface without cross-customer leakage.

Correct answer: A

Explanation of each choice

A.

The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed. Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

B.

This would be valid for another situation: Two route sources advertise an identical subnet; engineers compare IGP metric values while ignoring Junos inter-protocol preference. It does not establish that the failing boundary in this scenario works; verify: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

C.

The observation confirms a different component's behavior. Its source context is: A provider expects selected interface routes from an underlay RIB to be available in a second table, but the secondary table has no copied routes. In this case the success criterion is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

D.

That check proves something else, such as: A provider migrates a service into a separate virtual routing instance but tests only inet.0 and falsely concludes that the tenant route is absent. It could pass while the stated problem remains. The targeted evidence here is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

Question 23

An architecture review at Stonebridge Hospitality examines the following symptom: An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. What Junos or protocol mechanism is most directly responsible?

  1. A static route remains eligible based on configured next-hop resolution and route preference; dynamic protocols do not automatically repair an incorrectly pinned route.
  2. A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor.
  3. A Junos RIB group imports routes into a defined primary and additional routing table when attached to the correct configuration context.
  4. Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

Correct answer: B

Explanation of each choice

A.

The statement can be true when A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. But it does not explain the reported failure. Here: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

B.

A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor. The key distinction is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition. Accordingly the remedy is: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

C.

This explains a separate protocol behavior: A provider expects selected interface routes from an underlay RIB to be available in a second table, but the secondary table has no copied routes. In the current facts, the controlling mechanism is: A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor.

D.

The statement can be true when A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. But it does not explain the reported failure. Here: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

Question 24

The team at Stonebridge Hospitality defers a fix for this condition: An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. What failure is most likely if no targeted control is applied?

  1. The unintended route stays active and can override a healthier dynamic path during failure recovery or maintenance.
  2. An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.
  3. Traffic can bypass the required service path or reach a routing instance with no usable route, creating policy bypass or a blackhole.
  4. Unmatched traffic can loop or provoke inappropriate error traffic if the route's terminal next-hop behavior is not designed explicitly.

Correct answer: B

Explanation of each choice

A.

The concern could occur elsewhere when A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. For the stated scenario, the immediate risk is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

B.

An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path. The direct mitigation is: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

C.

It is a risk in another topology or protocol state: A packet class identified by source address needs to use a dedicated service routing table, but packets still follow the global destination-based path. Here the most direct failure path is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

D.

The concern could occur elsewhere when An operations runbook treats discard and reject forwarding actions as interchangeable and fails to explain the expected behavior for unmatched packets. For the stated scenario, the immediate risk is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

Question 25

During provider troubleshooting at Stonebridge Hospitality, this symptom is observed: An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. Which targeted inspection should precede remediation?

  1. Identify the ingress logical interface's routing-instance membership and inspect the corresponding instance RIB and forwarding table, not just inet.0.
  2. Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.
  3. Inspect the precise prefix in the routing table and the resolved next-hop/forwarding entry, then compare the active static configuration with the working topology.
  4. Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

Correct answer: D

Explanation of each choice

A.

This check may help with another root cause, for example: Two wholesale customers use overlapping IPv4 ranges and route lookups occur in the default table, causing one tenant's prefix to shadow the other's. It does not test the first failed condition; start with: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

B.

That evidence could be normal while the reported defect persists. It is aimed at: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. Instead inspect: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

C.

The check diagnoses a different layer of service. Its source issue is: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. The relevant initial check is: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

D.

Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor. Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

Question 26

At Canal City University, a service provider router shows this failure: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. What is the best targeted configuration or operations action?

  1. Select and document the intended discard versus reject next-hop behavior on the protective route, while preserving active more-specific routes for legitimate destinations.
  2. Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.
  3. Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.
  4. Inspect the Junos martian route configuration and classification and block or deliberately document any exception before accepting the questionable prefix.

Correct answer: C

Explanation of each choice

A.

The other action is relevant when An operations runbook treats discard and reject forwarding actions as interchangeable and fails to explain the expected behavior for unmatched packets. The current case instead requires: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default. The distinction is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

B.

That would address a separate configuration fault: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. This stem identifies a different cause, corrected by: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

C.

Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default. The case-specific reason is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition. A direct acceptance test is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

D.

The other action is relevant when A routing policy change appears to accept a reserved loopback or multicast source as an ordinary Internet destination, and the team needs to separate policy bugs from invalid route treatment. The current case instead requires: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default. The distinction is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

Question 27

A change auditor at Canal City University must validate remediation of this finding: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. Which test outcome is the strongest acceptance evidence?

  1. The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.
  2. Each tenant prefix is present in its own instance-specific routing table and traffic exits through that tenant's correct interface without cross-customer leakage.
  3. The active route and installed forwarding entry for the affected prefix point toward the reachable intended neighbor, and test traffic succeeds over the selected path.
  4. The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

Correct answer: A

Explanation of each choice

A.

The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed. Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

B.

That check proves something else, such as: Two wholesale customers use overlapping IPv4 ranges and route lookups occur in the default table, causing one tenant's prefix to shadow the other's. It could pass while the stated problem remains. The targeted evidence here is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

C.

This would be valid for another situation: A service edge was renumbered and its manually configured static next hop still points to the former address, blackholing one customer subnet despite healthy dynamic adjacencies. It does not establish that the failing boundary in this scenario works; verify: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

D.

The observation confirms a different component's behavior. Its source context is: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. In this case the success criterion is: The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.

Question 28

The operations training team at Canal City University discusses this issue: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. Which technical explanation matches the intended correction?

  1. Filter-based forwarding applies a routing-instance lookup decision based on a firewall filter rather than relying only on the ordinary destination table.
  2. A discard route silently drops packets; a reject route drops them while sending an unreachable response when supported, and longest-prefix matching still favors specifics.
  3. A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor.
  4. Between competing route sources for an identical destination, Junos normally prefers the route with the lower route-preference value before forwarding installation.

Correct answer: C

Explanation of each choice

A.

This explains a separate protocol behavior: A provider's firewall filter counts customer steering matches yet tagged traffic goes to the ordinary next hop because the `then routing-instance` forwarding path was not verified. In the current facts, the controlling mechanism is: A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor.

B.

The statement can be true when A provider intends a protective summary for address space with sparse more-specific destinations but needs unmatched traffic to be dropped predictably rather than looped. But it does not explain the reported failure. Here: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

C.

A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor. The key distinction is: Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition. Accordingly the remedy is: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

D.

This explains a separate protocol behavior: A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. In the current facts, the controlling mechanism is: A Junos generated route depends on active contributing more-specific routes and can derive its next hop from the primary contributor.

Question 29

At Canal City University, a service acceptance review considers the unresolved issue: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. Which operational exposure follows most directly?

  1. Unmatched traffic can loop or provoke inappropriate error traffic if the route's terminal next-hop behavior is not designed explicitly.
  2. Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.
  3. An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.
  4. Traffic for the specific prefix continues to follow the dead or incorrect next hop instead of recovering through an available alternate path.

Correct answer: C

Explanation of each choice

A.

It is a risk in another topology or protocol state: An operations runbook treats discard and reject forwarding actions as interchangeable and fails to explain the expected behavior for unmatched packets. Here the most direct failure path is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

B.

The concern could occur elsewhere when Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. For the stated scenario, the immediate risk is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

C.

An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path. The direct mitigation is: Use a policy-controlled generated route that becomes active only with the intended qualifying active contributing route, rather than an unconditional default.

D.

It is a risk in another topology or protocol state: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. Here the most direct failure path is: An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.

Question 30

Before changing configuration at Canal City University, an engineer investigates: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. Which first diagnostic most directly tests the suspected cause?

  1. Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.
  2. Inspect the precise prefix in the routing table and the resolved next-hop/forwarding entry, then compare the active static configuration with the working topology.
  3. Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.
  4. Inspect the protective route's next-hop type and run tests for both a known more-specific destination and an unmatched address in the summary.

Correct answer: A

Explanation of each choice

A.

Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor. Generated route activation is conditional on route contribution; merely raising an OSPF interface metric does not enforce the required default-route condition.

B.

This check may help with another root cause, for example: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. It does not test the first failed condition; start with: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

C.

That evidence could be normal while the reported defect persists. It is aimed at: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. Instead inspect: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

D.

The check diagnoses a different layer of service. Its source issue is: A provider intends a protective summary for address space with sparse more-specific destinations but needs unmatched traffic to be dropped predictably rather than looped. The relevant initial check is: Inspect contributor activity, the generate configuration and generated default in the RIB while deliberately withdrawing and restoring the qualifying contributor.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports