Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 69

Question 680

A support escalation at Redleaf Airports describes: A provider observes end-to-end label-switched traffic loss but checks only an IP traceroute and concludes MPLS is healthy. Where should the Junos operator look first for decisive evidence?

  1. Inspect the ingress route next hop, inet.3 LSP resolution when applicable and the outgoing label stack with a core-facing packet capture.
  2. Check each LSP path's signaling state and hop constraints independently, then test traffic during a controlled primary path failure.
  3. Compare LSP operational state, route recursion and MPLS forwarding entries hop-by-hop, including label-aware probes where supported.
  4. Inspect RSVP session/path errors, ERO or hop constraints, resource availability and LSP operational detail on the failing hop.

Correct answer: C

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: An MPLS service ingress forwards plain IP over a core link instead of imposing the transport label despite a valid route to the remote egress. Instead inspect: Compare LSP operational state, route recursion and MPLS forwarding entries hop-by-hop, including label-aware probes where supported.

B.

The check diagnoses a different layer of service. Its source issue is: A provider expects a preplanned backup RSVP path to protect traffic but a primary transport failure causes prolonged loss. The relevant initial check is: Compare LSP operational state, route recursion and MPLS forwarding entries hop-by-hop, including label-aware probes where supported.

C.

Compare LSP operational state, route recursion and MPLS forwarding entries hop-by-hop, including label-aware probes where supported. Successful plain-IP ping does not validate the label-switched forwarding plane or the service's active LSP.

D.

That evidence could be normal while the reported defect persists. It is aimed at: An explicitly constrained MPLS LSP should avoid one core link, but its RSVP-TE signaling never completes because a transit hop lacks appropriate resources. Instead inspect: Compare LSP operational state, route recursion and MPLS forwarding entries hop-by-hop, including label-aware probes where supported.

Question 681

During a Junos network change at Firthbank Medical, the engineer observes: An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. Which remediation most directly fixes the described problem?

  1. Enable and validate appropriate multiprotocol BGP IPv6-unicast family capability and import/export policy with usable IPv6 next-hop reachability.
  2. Create an appropriate IPv6-over-IPv4 tunnel between reachable endpoints, enabling correct IPv6 routing and MTU handling over the encapsulated path.
  3. Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.
  4. Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

Correct answer: D

Explanation of each choice

A.

That would address a separate configuration fault: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. This stem identifies a different cause, corrected by: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

B.

This action may apply to a different problem, for example: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. It does not repair the stated failure boundary. The case-specific reason is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

C.

The other action is relevant when Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. The current case instead requires: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope. The distinction is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

D.

Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope. The case-specific reason is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration. A direct acceptance test is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

Question 682

The Junos team at Firthbank Medical needs a success criterion for this defect: An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. Which observed result most precisely confirms the intended repair?

  1. The IPv6 prefixes appear in the intended inet6 route table and are advertised or received with appropriate MP-BGP family and next-hop attributes.
  2. IPv6 packets traverse the IPv4-only section inside the intended tunnel, with correct decapsulation and end-to-end IPv6 reachability without fragmentation surprises.
  3. Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.
  4. The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

Correct answer: D

Explanation of each choice

A.

That check proves something else, such as: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. It could pass while the stated problem remains. The targeted evidence here is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

B.

This would be valid for another situation: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. It does not establish that the failing boundary in this scenario works; verify: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

C.

The observation confirms a different component's behavior. Its source context is: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. In this case the success criterion is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

D.

The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface. The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

Question 683

While analyzing a service failure at Firthbank Medical, the following is observed: An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. MP-BGP uses address-family reachability attributes to carry IPv6 prefixes; an Established BGP session does not automatically enable every address family.
  2. IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability.
  3. IPv6-in-IPv4 tunneling carries IPv6 payloads through an IPv4 transport network by adding outer IPv4 encapsulation.
  4. GRE requires an underlay path to its remote outer endpoint that is independent of the tunnel's own inner forwarding path.

Correct answer: B

Explanation of each choice

A.

The statement can be true when An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. But it does not explain the reported failure. Here: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

B.

IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability. The key distinction is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration. Accordingly the remedy is: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

C.

This explains a separate protocol behavior: A provider cannot run native IPv6 across an intermediate IPv4-only segment yet needs an approved IPv6 connectivity path. In the current facts, the controlling mechanism is: IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability.

D.

The statement can be true when A static route was added for a GRE remote endpoint via the tunnel, and packets flap as the route resolves into the encapsulation path. But it does not explain the reported failure. Here: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

Question 684

The following provider defect remains uncorrected at Firthbank Medical: An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. What is the most direct service or security risk of leaving it unresolved?

  1. IPv6 destinations remain unreachable while operators are misled by an established IPv4 OSPF adjacency.
  2. IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.
  3. IPv6 routes are absent and dual-stack service only partially works even though BGP session state appears healthy.
  4. Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

Correct answer: B

Explanation of each choice

A.

The concern could occur elsewhere when An IPv6-only provider link forms an IPv4 OSPF adjacency but does not exchange any IPv6 routes because OSPFv3 was never enabled. For the stated scenario, the immediate risk is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

B.

IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces. The direct mitigation is: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

C.

It is a risk in another topology or protocol state: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. Here the most direct failure path is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

D.

The concern could occur elsewhere when A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. For the stated scenario, the immediate risk is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

Question 685

A support escalation at Firthbank Medical describes: An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. Where should the Junos operator look first for decisive evidence?

  1. Inspect OSPFv3 neighbor status and IPv6 route/LSA information separately from OSPFv2 state.
  2. Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.
  3. Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.
  4. Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

Correct answer: C

Explanation of each choice

A.

This check may help with another root cause, for example: An IPv6-only provider link forms an IPv4 OSPF adjacency but does not exchange any IPv6 routes because OSPFv3 was never enabled. It does not test the first failed condition; start with: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

B.

That evidence could be normal while the reported defect persists. It is aimed at: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. Instead inspect: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

C.

Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link. The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

D.

This check may help with another root cause, for example: A static route was added for a GRE remote endpoint via the tunnel, and packets flap as the route resolves into the encapsulation path. It does not test the first failed condition; start with: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

Question 686

The provider operations team at Cascade Hosting reports: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. Which implementation decision best corrects the cause?

  1. Configure the intended OSPFv3 adjacency for IPv6 on both participating links and verify its IPv6 route advertisements.
  2. Enable and validate appropriate multiprotocol BGP IPv6-unicast family capability and import/export policy with usable IPv6 next-hop reachability.
  3. Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.
  4. Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.

Correct answer: C

Explanation of each choice

A.

That would address a separate configuration fault: A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. This stem identifies a different cause, corrected by: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

B.

That would address a separate configuration fault: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. This stem identifies a different cause, corrected by: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

C.

Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope. The case-specific reason is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration. A direct acceptance test is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

D.

The other action is relevant when Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. The current case instead requires: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope. The distinction is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

Question 687

During a post-change check at Cascade Hosting, the original condition was: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. What evidence would validate the corrected behavior?

  1. The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.
  2. The IPv6 prefixes appear in the intended inet6 route table and are advertised or received with appropriate MP-BGP family and next-hop attributes.
  3. IPv6 packets traverse the IPv4-only section inside the intended tunnel, with correct decapsulation and end-to-end IPv6 reachability without fragmentation surprises.
  4. Traffic at realistic payload sizes traverses the GRE path without systematic fragmentation-needed loss or TCP blackhole symptoms.

Correct answer: A

Explanation of each choice

A.

The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface. The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

B.

That check proves something else, such as: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. It could pass while the stated problem remains. The targeted evidence here is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

C.

This would be valid for another situation: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. It does not establish that the failing boundary in this scenario works; verify: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

D.

The observation confirms a different component's behavior. Its source context is: Small GRE-tunneled packets work but larger TCP segments stall after a path change because GRE encapsulation exceeds the underlay MTU. In this case the success criterion is: The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.

Question 688

At Cascade Hosting, an engineer is asked to explain this case: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. Which underlying routing or switching principle accounts for the appropriate solution?

  1. OSPFv3 is the OSPF protocol variant used for IPv6 routing in this context; OSPFv2's IPv4 adjacency does not carry IPv6 network reachability.
  2. MP-BGP uses address-family reachability attributes to carry IPv6 prefixes; an Established BGP session does not automatically enable every address family.
  3. GRE requires an underlay path to its remote outer endpoint that is independent of the tunnel's own inner forwarding path.
  4. IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability.

Correct answer: D

Explanation of each choice

A.

This explains a separate protocol behavior: A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. In the current facts, the controlling mechanism is: IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability.

B.

The statement can be true when An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. But it does not explain the reported failure. Here: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

C.

That principle belongs to a different service stage: A static route was added for a GRE remote endpoint via the tunnel, and packets flap as the route resolves into the encapsulation path. The directly relevant mechanism is: IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability.

D.

IPv6 has its own address family and routing table; IPv4 default routes do not create IPv6 forwarding reachability. The key distinction is: The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration. Accordingly the remedy is: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

Question 689

A risk assessment at Cascade Hosting identifies: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. Which practical consequence is most specifically tied to this failure?

  1. Unaccounted encapsulation overhead and incorrect family setup can blackhole larger IPv6 packets or expose an unintended endpoint.
  2. IPv6 routes are absent and dual-stack service only partially works even though BGP session state appears healthy.
  3. IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.
  4. Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

Correct answer: C

Explanation of each choice

A.

The concern could occur elsewhere when Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. For the stated scenario, the immediate risk is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

B.

The concern could occur elsewhere when An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. For the stated scenario, the immediate risk is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

C.

IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces. The direct mitigation is: Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

D.

It is a risk in another topology or protocol state: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. Here the most direct failure path is: IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

Question 690

The on-call engineer at Cascade Hosting receives this fault report: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. What initial check best isolates the actual failing protocol stage?

  1. Inspect negotiated BGP families, IPv6 received/advertised paths, policy terms and next-hop reachability for inet6.
  2. Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.
  3. Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.
  4. Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: A dual-stack customer expects IPv6 routes over an existing BGP relationship, but the session negotiates only IPv4 unicast capability. It does not test the first failed condition; start with: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

B.

Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link. The root fault is IPv6 routing-family reachability, not missing IPv4 inet.0 static configuration.

C.

That evidence could be normal while the reported defect persists. It is aimed at: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. Instead inspect: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

D.

The check diagnoses a different layer of service. Its source issue is: A GRE tunnel's outer destination route is accidentally learned through the GRE interface itself, causing the tunnel to recursively depend on its own availability. The relevant initial check is: Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports