Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 73

Question 720

A support escalation at Maple Coast Retail describes: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. Where should the Junos operator look first for decisive evidence?

  1. Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.
  2. Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.
  3. Inspect OSPFv3 neighbor status and IPv6 route/LSA information separately from OSPFv2 state.
  4. Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. It does not test the first failed condition; start with: Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.

B.

Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes. A tunnel transports one protocol through another; adding IPv6 addresses to an unchanged IPv4-only transit link is not sufficient.

C.

That evidence could be normal while the reported defect persists. It is aimed at: A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. Instead inspect: Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.

D.

The check diagnoses a different layer of service. Its source issue is: A GRE tunnel's outer destination route is accidentally learned through the GRE interface itself, causing the tunnel to recursively depend on its own availability. The relevant initial check is: Verify outer IPv4 reachability, tunnel encapsulation family, IPv6 tunnel addressing and effective path MTU using appropriately sized probes.

Question 721

During a Junos network change at Cedar Coast Telecom, the engineer observes: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. Which remediation most directly fixes the described problem?

  1. Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.
  2. Reduce the tunnel's effective MTU or apply suitable supported PMTUD/MSS handling so encapsulated packets fit the actual underlay.
  3. Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.
  4. Enable and validate appropriate multiprotocol BGP IPv6-unicast family capability and import/export policy with usable IPv6 next-hop reachability.

Correct answer: A

Explanation of each choice

A.

Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint. A direct acceptance test is: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

B.

The other action is relevant when A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. The current case instead requires: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability. The distinction is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

C.

This action may apply to a different problem, for example: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. It does not repair the stated failure boundary. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

D.

This action may apply to a different problem, for example: A dual-stack customer expects IPv6 routes over an existing BGP relationship, but the session negotiates only IPv4 unicast capability. It does not repair the stated failure boundary. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

Question 722

The Junos team at Cedar Coast Telecom needs a success criterion for this defect: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. Which observed result most precisely confirms the intended repair?

  1. Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.
  2. Traffic at realistic payload sizes traverses the GRE path without systematic fragmentation-needed loss or TCP blackhole symptoms.
  3. IPv6 packets traverse the IPv4-only section inside the intended tunnel, with correct decapsulation and end-to-end IPv6 reachability without fragmentation surprises.
  4. The OSPFv3 neighbor establishes correctly and expected IPv6 prefixes are learned in the IPv6 routing table.

Correct answer: A

Explanation of each choice

A.

Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes. GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

B.

The observation confirms a different component's behavior. Its source context is: A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. In this case the success criterion is: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

C.

That check proves something else, such as: A provider cannot run native IPv6 across an intermediate IPv4-only segment yet needs an approved IPv6 connectivity path. It could pass while the stated problem remains. The targeted evidence here is: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

D.

This would be valid for another situation: A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. It does not establish that the failing boundary in this scenario works; verify: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

Question 723

While analyzing a service failure at Cedar Coast Telecom, the following is observed: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. GRE introduces extra outer IP and encapsulation bytes, reducing effective payload MTU compared with the underlay interface.
  2. GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.
  3. IPv6-in-IPv4 tunneling carries IPv6 payloads through an IPv4 transport network by adding outer IPv4 encapsulation.
  4. MP-BGP uses address-family reachability attributes to carry IPv6 prefixes; an Established BGP session does not automatically enable every address family.

Correct answer: B

Explanation of each choice

A.

That principle belongs to a different service stage: Small GRE-tunneled packets work but larger TCP segments stall after a path change because GRE encapsulation exceeds the underlay MTU. The directly relevant mechanism is: GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.

B.

GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device. The key distinction is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint. Accordingly the remedy is: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.

C.

The statement can be true when A provider cannot run native IPv6 across an intermediate IPv4-only segment yet needs an approved IPv6 connectivity path. But it does not explain the reported failure. Here: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

D.

That principle belongs to a different service stage: A dual-stack customer expects IPv6 routes over an existing BGP relationship, but the session negotiates only IPv4 unicast capability. The directly relevant mechanism is: GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.

Question 724

The following provider defect remains uncorrected at Cedar Coast Telecom: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. What is the most direct service or security risk of leaving it unresolved?

  1. Large packets can be lost or fragmented repeatedly, affecting real applications while small test packets falsely appear healthy.
  2. Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.
  3. Unaccounted encapsulation overhead and incorrect family setup can blackhole larger IPv6 packets or expose an unintended endpoint.
  4. IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

Correct answer: B

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: Small GRE-tunneled packets work but larger TCP segments stall after a path change because GRE encapsulation exceeds the underlay MTU. The described fault instead exposes: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

B.

Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces. The direct mitigation is: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.

C.

The concern could occur elsewhere when A provider cannot run native IPv6 across an intermediate IPv4-only segment yet needs an approved IPv6 connectivity path. For the stated scenario, the immediate risk is: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

D.

That consequence is more closely associated with another deficiency, such as: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. The described fault instead exposes: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

Question 725

A support escalation at Cedar Coast Telecom describes: Two remote routers intend to exchange isolated routes through GRE, but the local tunnel configuration still names the retired remote outer endpoint even though the new endpoint is reachable over the underlay. Where should the Junos operator look first for decisive evidence?

  1. Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.
  2. Measure underlay and tunnel MTUs, send size-controlled probes and inspect ICMP fragmentation-needed or packet captures at tunnel edges.
  3. Inspect OSPFv3 neighbor status and IPv6 route/LSA information separately from OSPFv2 state.
  4. Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.

Correct answer: A

Explanation of each choice

A.

Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints. GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

B.

The check diagnoses a different layer of service. Its source issue is: A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. The relevant initial check is: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

C.

This check may help with another root cause, for example: An IPv6-only provider link forms an IPv4 OSPF adjacency but does not exchange any IPv6 routes because OSPFv3 was never enabled. It does not test the first failed condition; start with: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

D.

That evidence could be normal while the reported defect persists. It is aimed at: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. Instead inspect: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

Question 726

The provider operations team at ValleyCross Fiber reports: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. Which implementation decision best corrects the cause?

  1. Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.
  2. Reduce the tunnel's effective MTU or apply suitable supported PMTUD/MSS handling so encapsulated packets fit the actual underlay.
  3. Create an appropriate IPv6-over-IPv4 tunnel between reachable endpoints, enabling correct IPv6 routing and MTU handling over the encapsulated path.
  4. Install or correct the IPv6 static route in the appropriate inet6 routing table with a reachable next hop and correct interface scope.

Correct answer: A

Explanation of each choice

A.

Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint. A direct acceptance test is: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

B.

This action may apply to a different problem, for example: Small GRE-tunneled packets work but larger TCP segments stall after a path change because GRE encapsulation exceeds the underlay MTU. It does not repair the stated failure boundary. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

C.

The other action is relevant when Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. The current case instead requires: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability. The distinction is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

D.

This action may apply to a different problem, for example: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. It does not repair the stated failure boundary. The case-specific reason is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

Question 727

During a post-change check at ValleyCross Fiber, the original condition was: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. What evidence would validate the corrected behavior?

  1. The destination is active in inet6.0 or the intended IPv6 instance table and forwarding resolves to the correct IPv6 neighbor/interface.
  2. IPv6 packets traverse the IPv4-only section inside the intended tunnel, with correct decapsulation and end-to-end IPv6 reachability without fragmentation surprises.
  3. Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.
  4. The OSPFv3 neighbor establishes correctly and expected IPv6 prefixes are learned in the IPv6 routing table.

Correct answer: C

Explanation of each choice

A.

This would be valid for another situation: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. It does not establish that the failing boundary in this scenario works; verify: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

B.

This would be valid for another situation: A provider cannot run native IPv6 across an intermediate IPv4-only segment yet needs an approved IPv6 connectivity path. It does not establish that the failing boundary in this scenario works; verify: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

C.

Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes. GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

D.

That check proves something else, such as: An IPv6-only provider link forms an IPv4 OSPF adjacency but does not exchange any IPv6 routes because OSPFv3 was never enabled. It could pass while the stated problem remains. The targeted evidence here is: Outer GRE packets arrive at the actual remote endpoint and inner packets emerge on the correct tunnel interface with approved routes.

Question 728

At ValleyCross Fiber, an engineer is asked to explain this case: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. Which underlying routing or switching principle accounts for the appropriate solution?

  1. GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.
  2. GRE introduces extra outer IP and encapsulation bytes, reducing effective payload MTU compared with the underlay interface.
  3. IPv6-in-IPv4 tunneling carries IPv6 payloads through an IPv4 transport network by adding outer IPv4 encapsulation.
  4. OSPFv3 is the OSPF protocol variant used for IPv6 routing in this context; OSPFv2's IPv4 adjacency does not carry IPv6 network reachability.

Correct answer: A

Explanation of each choice

A.

GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device. The key distinction is: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint. Accordingly the remedy is: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.

B.

That principle belongs to a different service stage: Small GRE-tunneled packets work but larger TCP segments stall after a path change because GRE encapsulation exceeds the underlay MTU. The directly relevant mechanism is: GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.

C.

This explains a separate protocol behavior: Two dual-stack edges plan to transport IPv6 packets across an IPv4-only core, but the existing tunnel encapsulates the wrong protocol family. In the current facts, the controlling mechanism is: GRE encapsulates an inner packet in an outer IP header addressed to the configured remote endpoint; a stale destination sends outer packets to the wrong device.

D.

The statement can be true when An IPv6-only provider link forms an IPv4 OSPF adjacency but does not exchange any IPv6 routes because OSPFv3 was never enabled. But it does not explain the reported failure. Here: GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

Question 729

A risk assessment at ValleyCross Fiber identifies: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. Which practical consequence is most specifically tied to this failure?

  1. Large packets can be lost or fragmented repeatedly, affecting real applications while small test packets falsely appear healthy.
  2. Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.
  3. IPv6 destinations remain unreachable while operators are misled by an established IPv4 OSPF adjacency.
  4. IPv6 traffic blackholes despite fully functional IPv4 routing and healthy Ethernet interfaces.

Correct answer: B

Explanation of each choice

A.

The concern could occur elsewhere when A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. For the stated scenario, the immediate risk is: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

B.

Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces. The direct mitigation is: Correct the GRE tunnel source and destination to reachable outer transport addresses and enable the intended tunnel interface and routed reachability.

C.

The concern could occur elsewhere when A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. For the stated scenario, the immediate risk is: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

D.

The concern could occur elsewhere when An edge has working IPv4 defaults but no IPv6 path to a remote subnet after the customer's IPv6 handoff is enabled. For the stated scenario, the immediate risk is: Packets can be sent to an obsolete encapsulation endpoint and disappear despite normal reachability between unrelated router interfaces.

Question 730

The on-call engineer at ValleyCross Fiber receives this fault report: A provider migrated a tunnel endpoint to a new loopback address without updating the remote GRE destination, while physical IP connectivity still works. What initial check best isolates the actual failing protocol stage?

  1. Measure underlay and tunnel MTUs, send size-controlled probes and inspect ICMP fragmentation-needed or packet captures at tunnel edges.
  2. Inspect negotiated BGP families, IPv6 received/advertised paths, policy terms and next-hop reachability for inet6.
  3. Inspect `show route table inet6.0` for the destination, next-hop resolution and IPv6 neighbor state on the intended transit link.
  4. Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

Correct answer: D

Explanation of each choice

A.

This check may help with another root cause, for example: A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. It does not test the first failed condition; start with: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

B.

The check diagnoses a different layer of service. Its source issue is: A dual-stack customer expects IPv6 routes over an existing BGP relationship, but the session negotiates only IPv4 unicast capability. The relevant initial check is: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

C.

The check diagnoses a different layer of service. Its source issue is: An IPv6 service route points to a next-hop address on the wrong logical link, while neighbor discovery succeeds on the real transit interface. The relevant initial check is: Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints.

D.

Inspect tunnel endpoint addresses and underlay routes, then capture GRE protocol 47 traffic at both intended endpoints. GRE forwarding depends first on outer IP endpoint reachability; modifying the inner IGP metric does not fix an unreachable tunnel endpoint.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports