Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 76

Question 750

Before changing configuration at Baystone Energy, an engineer investigates: A static route was added for a GRE remote endpoint via the tunnel, and packets flap as the route resolves into the encapsulation path. Which first diagnostic most directly tests the suspected cause?

  1. Measure underlay and tunnel MTUs, send size-controlled probes and inspect ICMP fragmentation-needed or packet captures at tunnel edges.
  2. Inspect OSPFv3 neighbor status and IPv6 route/LSA information separately from OSPFv2 state.
  3. Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.
  4. Inspect negotiated BGP families, IPv6 received/advertised paths, policy terms and next-hop reachability for inet6.

Correct answer: C

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: A service uses a GRE tunnel across a reduced-MTU carrier link, and oversized packets are dropped while basic ping succeeds. The relevant initial check is: Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

B.

That evidence could be normal while the reported defect persists. It is aimed at: A migration enables OSPFv3 on one transit interface but the neighbor is configured only for OSPFv2, leaving the IPv6 topology unadvertised. Instead inspect: Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

C.

Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices. Outer endpoint transport and inner tunneled reachability are distinct routing layers; sending the underlay endpoint through its own tunnel is circular.

D.

The check diagnoses a different layer of service. Its source issue is: An established IPv4 BGP peer exchanges inet unicast prefixes but receives no IPv6 routes because the IPv6 address family is not configured. The relevant initial check is: Inspect the outer endpoint route and recursive next hop with the tunnel enabled/disabled, then compare inner route choices.

Question 751

At Westhaven Software, a service provider router shows this failure: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. What is the best targeted configuration or operations action?

  1. Configure compatible supported graceful-restart behavior between routing peers and verify helper participation during a controlled routing-process restart.
  2. Enable supported GRES plus nonstop active routing with proper synchronization and validate routing-protocol continuity across a controlled switchover.
  3. Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.
  4. Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

Correct answer: C

Explanation of each choice

A.

This action may apply to a different problem, for example: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. It does not repair the stated failure boundary. The case-specific reason is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

B.

The other action is relevant when A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. The current case instead requires: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state. The distinction is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

C.

Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state. The case-specific reason is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle. A direct acceptance test is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

D.

This action may apply to a different problem, for example: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. It does not repair the stated failure boundary. The case-specific reason is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

Question 752

A change auditor at Westhaven Software must validate remediation of this finding: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. Which test outcome is the strongest acceptance evidence?

  1. Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.
  2. Forwarding and relevant routing adjacencies remain stable under the documented NSR/GRES switchover test, with backup protocol state synchronized beforehand.
  3. During a controlled master failure, the backup assumes the virtual gateway role and hosts continue to reach the same default-gateway IP through the surviving router.
  4. A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

Correct answer: A

Explanation of each choice

A.

Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy. A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

B.

The observation confirms a different component's behavior. Its source context is: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. In this case the success criterion is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

C.

That check proves something else, such as: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. It could pass while the stated problem remains. The targeted evidence here is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

D.

This would be valid for another situation: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. It does not establish that the failing boundary in this scenario works; verify: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

Question 753

The operations training team at Westhaven Software discusses this issue: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. Which technical explanation matches the intended correction?

  1. VRRP provides a virtual first-hop gateway with master/backup election, distinct from physical interface IPs or dynamic routing best paths.
  2. GRES preserves interface/kernel forwarding state; NSR additionally preserves routing protocol state on a backup engine and requires GRES. Nonstop bridging (NSB) addresses related Layer 2 bridging state continuity.
  3. Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.
  4. Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state.

Correct answer: D

Explanation of each choice

A.

That principle belongs to a different service stage: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. The directly relevant mechanism is: Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state.

B.

This explains a separate protocol behavior: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. In the current facts, the controlling mechanism is: Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state.

C.

The statement can be true when An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. But it does not explain the reported failure. Here: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

D.

Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state. The key distinction is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle. Accordingly the remedy is: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

Question 754

At Westhaven Software, a service acceptance review considers the unresolved issue: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. Which operational exposure follows most directly?

  1. An unprotected gateway failure disconnects local subnet clients even when upstream core routes remain available.
  2. Without restart assistance, peers may immediately withdraw routes and cause traffic interruption while the restarting router recovers.
  3. Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.
  4. Traffic may continue briefly but route adjacencies reset and reconverge if GRES alone is mistaken for full routing-protocol nonstop operation.

Correct answer: C

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. The described fault instead exposes: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

B.

It is a risk in another topology or protocol state: An operator mistakes routing-engine switchover forwarding preservation for a guarantee that peers will retain protocol routes through restart. Here the most direct failure path is: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

C.

Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure. The direct mitigation is: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

D.

That consequence is more closely associated with another deficiency, such as: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. The described fault instead exposes: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

Question 755

Before changing configuration at Westhaven Software, an engineer investigates: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. Which first diagnostic most directly tests the suspected cause?

  1. Inspect VRRP group state, priority, virtual address and advertisements on both routers and measure default-gateway traffic during failover.
  2. Inspect negotiated graceful-restart capability and restart/helper state and capture neighbor route behavior during a controlled exercise.
  3. Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.
  4. Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

Correct answer: D

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. Instead inspect: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

B.

The check diagnoses a different layer of service. Its source issue is: An operator mistakes routing-engine switchover forwarding preservation for a guarantee that peers will retain protocol routes through restart. The relevant initial check is: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

C.

This check may help with another root cause, for example: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. It does not test the first failed condition; start with: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

D.

Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors. A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

Question 756

During a Junos network change at Eastvale MetroNet, the engineer observes: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Which remediation most directly fixes the described problem?

  1. Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.
  2. Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.
  3. Align and validate VRRP group, virtual IP, interface membership and priority/preemption policy on the primary and backup gateways.
  4. Configure compatible supported graceful-restart behavior between routing peers and verify helper participation during a controlled routing-process restart.

Correct answer: B

Explanation of each choice

A.

That would address a separate configuration fault: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. This stem identifies a different cause, corrected by: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

B.

Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state. The case-specific reason is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle. A direct acceptance test is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

C.

The other action is relevant when A customer changes its physical router while preserving endpoint configurations; the VRRP backup never becomes master due to incompatible group settings or priorities. The current case instead requires: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state. The distinction is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

D.

That would address a separate configuration fault: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. This stem identifies a different cause, corrected by: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

Question 757

The Junos team at Eastvale MetroNet needs a success criterion for this defect: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Which observed result most precisely confirms the intended repair?

  1. Neighbors temporarily retain permissible stale forwarding routes during the restart window and converge correctly when the control plane returns.
  2. A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.
  3. Forwarding and relevant routing adjacencies remain stable under the documented NSR/GRES switchover test, with backup protocol state synchronized beforehand.
  4. Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

Correct answer: D

Explanation of each choice

A.

That check proves something else, such as: An operator mistakes routing-engine switchover forwarding preservation for a guarantee that peers will retain protocol routes through restart. It could pass while the stated problem remains. The targeted evidence here is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

B.

This would be valid for another situation: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. It does not establish that the failing boundary in this scenario works; verify: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

C.

The observation confirms a different component's behavior. Its source context is: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. In this case the success criterion is: Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.

D.

Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy. A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

Question 758

While analyzing a service failure at Eastvale MetroNet, the following is observed: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. Graceful restart uses protocol extensions and neighbor cooperation to preserve forwarding during supported control-plane restarts; it is distinct from stateful NSR.
  2. Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.
  3. Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state.
  4. VRRP provides a virtual first-hop gateway with master/backup election, distinct from physical interface IPs or dynamic routing best paths.

Correct answer: C

Explanation of each choice

A.

The statement can be true when An operator mistakes routing-engine switchover forwarding preservation for a guarantee that peers will retain protocol routes through restart. But it does not explain the reported failure. Here: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

B.

That principle belongs to a different service stage: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. The directly relevant mechanism is: Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state.

C.

Link aggregation presents multiple physical Ethernet members as one logical link when both peers agree on aggregation and LACP state. The key distinction is: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle. Accordingly the remedy is: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

D.

The statement can be true when Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. But it does not explain the reported failure. Here: A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

Question 759

The following provider defect remains uncorrected at Eastvale MetroNet: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. What is the most direct service or security risk of leaving it unresolved?

  1. Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.
  2. Without restart assistance, peers may immediately withdraw routes and cause traffic interruption while the restarting router recovers.
  3. A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.
  4. An unprotected gateway failure disconnects local subnet clients even when upstream core routes remain available.

Correct answer: A

Explanation of each choice

A.

Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure. The direct mitigation is: Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.

B.

That consequence is more closely associated with another deficiency, such as: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. The described fault instead exposes: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

C.

It is a risk in another topology or protocol state: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. Here the most direct failure path is: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

D.

The concern could occur elsewhere when Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. For the stated scenario, the immediate risk is: Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.

Question 760

A support escalation at Eastvale MetroNet describes: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Where should the Junos operator look first for decisive evidence?

  1. Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.
  2. Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.
  3. Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.
  4. Inspect VRRP group state, priority, virtual address and advertisements on both routers and measure default-gateway traffic during failover.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. It does not test the first failed condition; start with: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

B.

Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors. A link's physical Up state is not equivalent to synchronized membership in the intended aggregated Ethernet bundle.

C.

The check diagnoses a different layer of service. Its source issue is: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. The relevant initial check is: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

D.

This check may help with another root cause, for example: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. It does not test the first failed condition; start with: Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports