Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 79

Question 780

During provider troubleshooting at Brookport Finance, this symptom is observed: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. Which targeted inspection should precede remediation?

  1. Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.
  2. Check the actual neighbor device, BPDU observations and interface spanning-tree edge/role state before changing port behavior.
  3. Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.
  4. Inspect negotiated graceful-restart capability and restart/helper state and capture neighbor route behavior during a controlled exercise.

Correct answer: A

Explanation of each choice

A.

Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover. Preserving the data plane with GRES is not the same as preserving the control plane with NSR.

B.

That evidence could be normal while the reported defect persists. It is aimed at: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. Instead inspect: Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.

C.

That evidence could be normal while the reported defect persists. It is aimed at: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Instead inspect: Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.

D.

The check diagnoses a different layer of service. Its source issue is: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. The relevant initial check is: Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.

Question 781

A production change request at Briarfield Healthcare includes this finding: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. What should the engineer change to address it?

  1. Designate only genuinely host-facing ports as appropriate RSTP edge ports and enable protections against receiving unexpected BPDUs.
  2. Enable supported GRES plus nonstop active routing with proper synchronization and validate routing-protocol continuity across a controlled switchover.
  3. Align and validate VRRP group, virtual IP, interface membership and priority/preemption policy on the primary and backup gateways.
  4. Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

Correct answer: D

Explanation of each choice

A.

The other action is relevant when A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. The current case instead requires: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response. The distinction is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

B.

The other action is relevant when A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. The current case instead requires: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response. The distinction is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

C.

That would address a separate configuration fault: Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. This stem identifies a different cause, corrected by: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

D.

Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response. The case-specific reason is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies. A direct acceptance test is: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

Question 782

After Briarfield Healthcare applies its proposed fix to this problem — An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. — which observation best proves the specific failure has been resolved?

  1. The host port forwards promptly while an unexpected BPDU is detected and handled by the configured protection policy.
  2. A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.
  3. Neighbors temporarily retain permissible stale forwarding routes during the restart window and converge correctly when the control plane returns.
  4. During a controlled master failure, the backup assumes the virtual gateway role and hosts continue to reach the same default-gateway IP through the surviving router.

Correct answer: B

Explanation of each choice

A.

The observation confirms a different component's behavior. Its source context is: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. In this case the success criterion is: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

B.

A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers. BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

C.

That check proves something else, such as: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. It could pass while the stated problem remains. The targeted evidence here is: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

D.

This would be valid for another situation: A customer changes its physical router while preserving endpoint configurations; the VRRP backup never becomes master due to incompatible group settings or priorities. It does not establish that the failing boundary in this scenario works; verify: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

Question 783

An architecture review at Briarfield Healthcare examines the following symptom: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. What Junos or protocol mechanism is most directly responsible?

  1. Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.
  2. RSTP edge-port treatment shortens convergence for a host attachment but must not be applied to a link that connects another bridge.
  3. GRES preserves interface/kernel forwarding state; NSR additionally preserves routing protocol state on a backup engine and requires GRES. Nonstop bridging (NSB) addresses related Layer 2 bridging state continuity.
  4. VRRP provides a virtual first-hop gateway with master/backup election, distinct from physical interface IPs or dynamic routing best paths.

Correct answer: A

Explanation of each choice

A.

Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed. The key distinction is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies. Accordingly the remedy is: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

B.

The statement can be true when A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. But it does not explain the reported failure. Here: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

C.

The statement can be true when A redundant-engine router forwards packets during a switchover but routing protocol sessions still reset because only GRES is configured. But it does not explain the reported failure. Here: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

D.

That principle belongs to a different service stage: A customer changes its physical router while preserving endpoint configurations; the VRRP backup never becomes master due to incompatible group settings or priorities. The directly relevant mechanism is: Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.

Question 784

The team at Briarfield Healthcare defers a fix for this condition: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. What failure is most likely if no targeted control is applied?

  1. A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.
  2. Mislabeling a switch-to-switch link as edge can permit a transient loop, while no edge setting causes avoidable endpoint startup delay.
  3. An unprotected gateway failure disconnects local subnet clients even when upstream core routes remain available.
  4. Without restart assistance, peers may immediately withdraw routes and cause traffic interruption while the restarting router recovers.

Correct answer: A

Explanation of each choice

A.

A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path. The direct mitigation is: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

B.

The concern could occur elsewhere when A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. For the stated scenario, the immediate risk is: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

C.

The concern could occur elsewhere when Customer hosts use a shared default gateway IP but lose reachability when the primary router fails because no backup gateway assumes the virtual address. For the stated scenario, the immediate risk is: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

D.

That consequence is more closely associated with another deficiency, such as: An operator mistakes routing-engine switchover forwarding preservation for a guarantee that peers will retain protocol routes through restart. The described fault instead exposes: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

Question 785

During provider troubleshooting at Briarfield Healthcare, this symptom is observed: An OSPF or BGP route stays installed for too long after an indirect forwarding failure because normal protocol hold timers have not expired. Which targeted inspection should precede remediation?

  1. Inspect negotiated graceful-restart capability and restart/helper state and capture neighbor route behavior during a controlled exercise.
  2. Inspect chassis redundancy and NSR status, backup routing process synchronization, and neighbor sessions during an approved switchover.
  3. Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.
  4. Inspect LACP actor/partner state, physical member association and ae interface operational details on both neighbors.

Correct answer: C

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. Instead inspect: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

B.

The check diagnoses a different layer of service. Its source issue is: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. The relevant initial check is: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

C.

Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes. BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

D.

That evidence could be normal while the reported defect persists. It is aimed at: An access device bundles ports into one aggregated interface while the remote peer places one port into a different aggregation group. Instead inspect: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

Question 786

At Cloverbank Mobile, a service provider router shows this failure: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. What is the best targeted configuration or operations action?

  1. Designate only genuinely host-facing ports as appropriate RSTP edge ports and enable protections against receiving unexpected BPDUs.
  2. Correct compatible LAG member association and LACP configuration at both ends, then verify active members and per-member forwarding state.
  3. Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.
  4. Configure compatible supported graceful-restart behavior between routing peers and verify helper participation during a controlled routing-process restart.

Correct answer: C

Explanation of each choice

A.

This action may apply to a different problem, for example: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. It does not repair the stated failure boundary. The case-specific reason is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

B.

This action may apply to a different problem, for example: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. It does not repair the stated failure boundary. The case-specific reason is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

C.

Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response. The case-specific reason is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies. A direct acceptance test is: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

D.

That would address a separate configuration fault: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. This stem identifies a different cause, corrected by: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

Question 787

A change auditor at Cloverbank Mobile must validate remediation of this finding: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. Which test outcome is the strongest acceptance evidence?

  1. The host port forwards promptly while an unexpected BPDU is detected and handled by the configured protection policy.
  2. Both intended links show synchronized collecting/distributing membership and the aggregated interface carries traffic with expected redundancy.
  3. Forwarding and relevant routing adjacencies remain stable under the documented NSR/GRES switchover test, with backup protocol state synchronized beforehand.
  4. A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

Correct answer: D

Explanation of each choice

A.

This would be valid for another situation: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. It does not establish that the failing boundary in this scenario works; verify: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

B.

This would be valid for another situation: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. It does not establish that the failing boundary in this scenario works; verify: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

C.

The observation confirms a different component's behavior. Its source context is: A provider requires preserved BGP and IGP adjacency state during a Routing Engine failure on supported hardware, not just uninterrupted interfaces. In this case the success criterion is: A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers.

D.

A simulated forwarding-path loss causes BFD state to fail and the associated routing adjacency or path to react faster than ordinary hold timers. BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

Question 788

The operations training team at Cloverbank Mobile discusses this issue: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. Which technical explanation matches the intended correction?

  1. VRRP provides a virtual first-hop gateway with master/backup election, distinct from physical interface IPs or dynamic routing best paths.
  2. RSTP edge-port treatment shortens convergence for a host attachment but must not be applied to a link that connects another bridge.
  3. Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.
  4. Graceful restart uses protocol extensions and neighbor cooperation to preserve forwarding during supported control-plane restarts; it is distinct from stateful NSR.

Correct answer: C

Explanation of each choice

A.

The statement can be true when A customer changes its physical router while preserving endpoint configurations; the VRRP backup never becomes master due to incompatible group settings or priorities. But it does not explain the reported failure. Here: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

B.

This explains a separate protocol behavior: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. In the current facts, the controlling mechanism is: Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed.

C.

Bidirectional Forwarding Detection uses short independent liveness packets to tell a routing protocol when bidirectional forwarding has failed. The key distinction is: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies. Accordingly the remedy is: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

D.

The statement can be true when A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. But it does not explain the reported failure. Here: BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

Question 789

At Cloverbank Mobile, a service acceptance review considers the unresolved issue: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. Which operational exposure follows most directly?

  1. Mislabeling a switch-to-switch link as edge can permit a transient loop, while no edge setting causes avoidable endpoint startup delay.
  2. Misbundled members can silently drop frames, create loops or remove expected uplink capacity under failure.
  3. A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.
  4. Traffic may continue briefly but route adjacencies reset and reconverge if GRES alone is mistaken for full routing-protocol nonstop operation.

Correct answer: C

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. The described fault instead exposes: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

B.

That consequence is more closely associated with another deficiency, such as: A two-link provider uplink is configured as a LAG, but one member is out of synchronization and only a single link forwards. The described fault instead exposes: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

C.

A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path. The direct mitigation is: Configure supported BFD sessions for the intended routing peers with realistic negotiated detection intervals and validate the resulting routing response.

D.

The concern could occur elsewhere when A redundant-engine router forwards packets during a switchover but routing protocol sessions still reset because only GRES is configured. For the stated scenario, the immediate risk is: A silent forwarding fault can blackhole traffic until long routing-protocol timers expire, delaying use of an available backup path.

Question 790

Before changing configuration at Cloverbank Mobile, an engineer investigates: A provider wants quicker detection of a path fault when the Ethernet link stays physically Up, but changing application retry timers would not fix routing convergence. Which first diagnostic most directly tests the suspected cause?

  1. Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.
  2. Check the actual neighbor device, BPDU observations and interface spanning-tree edge/role state before changing port behavior.
  3. Inspect VRRP group state, priority, virtual address and advertisements on both routers and measure default-gateway traffic during failover.
  4. Inspect negotiated graceful-restart capability and restart/helper state and capture neighbor route behavior during a controlled exercise.

Correct answer: A

Explanation of each choice

A.

Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes. BFD speeds failure detection for supported paths; it does not itself select the alternate route or replace routing protocol policies.

B.

The check diagnoses a different layer of service. Its source issue is: A server-only switchport repeatedly transitions through unnecessary topology states when the connected endpoint restarts. The relevant initial check is: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

C.

The check diagnoses a different layer of service. Its source issue is: A customer changes its physical router while preserving endpoint configurations; the VRRP backup never becomes master due to incompatible group settings or priorities. The relevant initial check is: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

D.

This check may help with another root cause, for example: A routing process restarts on one provider router and a neighboring router immediately withdraws otherwise usable forwarding paths despite both supporting graceful restart. It does not test the first failed condition; start with: Check BFD peer state and negotiated intervals/multipliers, then correlate detection timestamps with routing-neighbor and route changes.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports