You save $69.98
300-415 Premium Bundle
- Premium File 480 Questions & Answers
- Last Update: Nov 11, 2026
- Training Course 112 Lectures
- Study Guide 874 Pages
You save $69.98
A Cisco SD-WAN deployment has completed the following step: Shape outbound traffic to the subscribed effective bandwidth before the provider bottleneck. The original case is: An ISP circuit is sold at 100 Mbps but the WAN Edge physical port transmits at 1 Gbps and causes provider-side drops. Which test result provides the strongest evidence that the change succeeded?
Measured egress traffic respects the configured rate and ISP policer drop counters decline. This observable result validates the corrective action: Shape outbound traffic to the subscribed effective bandwidth before the provider bottleneck.
The Edge resolves the intended service next hop and matched sessions reach the security appliance. That observation would verify another change: A branch relies on a regional security appliance but the policy uses a service destination that is not advertised in the correct VPN. The expected result instead is: Measured egress traffic respects the configured rate and ISP policer drop counters decline.
Congestion testing shows each tunnel respects its budget with appropriate class distribution. That observation would verify another change: A regional hub carries two IPsec tunnels with different committed bandwidth and one shared shaper starves the smaller path. The expected result instead is: Measured egress traffic respects the configured rate and ISP policer drop counters decline.
Packet captures show the required DSCP marking and downstream queue classification under approved trust settings. That observation would verify another change: A branch application is correctly classified but downstream routers give it best-effort treatment despite its priority. The expected result instead is: Measured egress traffic respects the configured rate and ISP policer drop counters decline.
A fabric administrator recommends the following change: Define a per-VPN service insertion policy that matches the relevant inter-zone flows. The triggering scenario is: A campus has three security zones and only traffic crossing zones needs a firewall hop. Which underlying SD-WAN behavior BEST explains the response?
Per-VPN service chaining provides selective inspection without forcing all fabric traffic through one service. This technical mechanism explains why the recommended action works: Define a per-VPN service insertion policy that matches the relevant inter-zone flows. A successful deployment should show: Tested inter-zone sessions use the firewall while same-zone traffic remains on the intended direct path.
Secure Internet Gateway connectivity depends on resilient tunnel routing as well as security policy. This principle is associated more closely with another situation: A cloud security tunnel to the primary SIG endpoint fails, yet the branch has a healthy backup internet circuit.
Service chaining requires both a matching flow policy and valid reachability to the service function. This principle is associated more closely with another situation: A branch relies on a regional security appliance but the policy uses a service destination that is not advertised in the correct VPN.
Service insertion can select redundant service functions when the service topology and policy support it. This principle is associated more closely with another situation: A regional firewall is being replaced and service-chain traffic must fail to a supported alternate instance.
Consider the following branch WAN issue: A branch Edge peers with a local OSPF router but its learned campus subnets do not enter the overlay. What is the most relevant operational risk in this situation?
Placing the OSPF process on transport VPN 0 instead of the intended service VPN can break isolation. Service-side OSPF exchanges LAN routes that can be redistributed into SD-WAN overlay routing. The recommended mitigation is: Configure OSPF in the correct service VPN and export intended learned routes into OMP.
Controller route visibility alone does not ensure compatible transport tunnel endpoints. That risk applies mainly to a different case: A branch has two healthy ISP connections but no encrypted tunnel appears toward a newly authorized remote site.
Using two unrelated gateway IPs without coordinated failover can disrupt local client traffic. That risk applies mainly to a different case: Two branch Edges face the same user VLAN and need a single virtual default gateway that survives device failure.
Assuming all platform images or templates support identical EIGRP behavior can cause deployment failure. That risk applies mainly to a different case: A legacy branch uses EIGRP toward the LAN and the new Catalyst Edge must maintain learned network reachability.
A Cisco Catalyst SD-WAN deployment engineer is handling this requirement: A replacement WAN Edge is installed at a branch but the old router's serial remains authorized and the new serial is missing. Which action BEST addresses the situation?
Update the device inventory and approved provisioning mapping for the replacement Edge. This is the targeted action for the stated case: A replacement WAN Edge is installed at a branch but the old router's serial remains authorized and the new serial is missing. The specific technical reason is: Cisco SD-WAN enrollment ties physical or virtual device identity to a managed authorization inventory. Verification should demonstrate: The new Edge is authorized and receives the correct site-specific configuration while the retired serial is removed.
Associate and deploy the supported policy group to the intended devices and confirm attachment state. This would help with a different network situation: A network team publishes a policy group but assumes the rule is active on every WAN Edge by default.
Prepare a supported bootstrap configuration with the correct organization, Validator endpoint, interfaces, and trust. This would help with a different network situation: A rugged site lacks internet access during installation but requires pre-staged SD-WAN identity and transport information.
Register its approved serial and use the supported Plug and Play or ZTP onboarding workflow with reachable Validator. This would help with a different network situation: A remote branch router arrives with no final configuration and the deployment team wants it to join the fabric without an engineer on site.
A Cisco Catalyst SD-WAN deployment engineer is handling this requirement: A guest VPN may use DIA but corporate finance traffic must continue through the inspected headquarters gateway. Which action BEST addresses the situation?
Match DIA by the correct service VPN and traffic class instead of adding a universal internet breakout. This is the targeted action for the stated case: A guest VPN may use DIA but corporate finance traffic must continue through the inspected headquarters gateway. The specific technical reason is: SD-WAN policy scopes direct internet breakout by service VPN and permitted traffic categories. Verification should demonstrate: Guest traffic exits locally while finance sessions follow the mandated central inspection route.
Define the appropriate backup default exit, NAT, and transport failover for the permitted traffic. This would help with a different network situation: Two broadband circuits provide DIA but the primary ISP becomes unavailable during an office-wide incident.
Create a centralized OMP control policy filtering accepted VPN routes by site or prefix list. This would help with a different network situation: A finance service VPN should learn only hub-originated networks while other branch prefixes remain isolated.
Apply the intended local security controls and cloud security integration before enabling DIA broadly. This would help with a different network situation: A branch enables direct internet breakout for employees without a firewall or DNS security plan.
A fabric administrator recommends the following change: Choose the supported management method and migrate the device association rather than using both simultaneously. The triggering scenario is: A Router is already attached to a legacy device template when a manager attempts to add it to a configuration group. Which underlying SD-WAN behavior BEST explains the response?
An SD-WAN Edge is typically managed by either a configuration group or a classic device template, not both. This technical mechanism explains why the recommended action works: Choose the supported management method and migrate the device association rather than using both simultaneously. A successful deployment should show: The Edge has one consistent configuration ownership method with no conflicting template attachment.
Feature profile parameters can be global, device-specific, or defaulted under configuration groups. This principle is associated more closely with another situation: A configuration group includes a system profile but an internet interface's IP address must vary by site.
SD-WAN policy and configuration objects require appropriate association and deployment to affect devices. This principle is associated more closely with another situation: A network team publishes a policy group but assumes the rule is active on every WAN Edge by default.
OMP controls how many paths per prefix are advertised or installed in the overlay routing process. This principle is associated more closely with another situation: One Edge has an OMP neighbor session that is up, yet route propagation stops after the configured path limit.
A Catalyst SD-WAN operations review encounters this case: A branch has two healthy ISP connections but no encrypted tunnel appears toward a newly authorized remote site. What failure mode is MOST directly associated with leaving it uncorrected?
Controller route visibility alone does not ensure compatible transport tunnel endpoints. Dynamic data-plane tunnels establish between eligible advertised transport locators with compatible encapsulation and reachability. The recommended mitigation is: Check candidate TLOC combinations, tunnel-interface settings, reachable ports and BFD negotiation.
Overlay routing changes cannot compensate for a missing transport underlay next hop. That risk applies mainly to a different case: A branch MPLS circuit has correct local IP addressing but cannot reach a remote overlay endpoint over the underlay.
Hardcoding a single branch's neighbor in the global template can break routing at every other site. That risk applies mainly to a different case: One device template is shared by 200 sites, but only the BGP neighbor address should differ per Edge.
A standby interface without valid TLOC advertisements may not be usable for overlay failover. That risk applies mainly to a different case: A link-redundant Edge should use a secondary internet TLOC when the primary data tunnel fails.
A Cisco Catalyst SD-WAN deployment engineer is handling this requirement: A team needs different control-plane behavior for one regional cluster without changing every site's routing. Which action BEST addresses the situation?
Create and attach a region-specific centralized control policy using the appropriate match lists. This is the targeted action for the stated case: A team needs different control-plane behavior for one regional cluster without changing every site's routing. The specific technical reason is: Controller-scoped policy attachments determine which Edge sites receive modified overlay routing. Verification should demonstrate: Affected regional Edges see intended OMP route changes while other regions retain their previous paths.
Create a centralized OMP control policy filtering accepted VPN routes by site or prefix list. This would help with a different network situation: A finance service VPN should learn only hub-originated networks while other branch prefixes remain isolated.
Apply supported OMP path preferences or TLOC attributes in a scoped centralized control policy. This would help with a different network situation: A regional fabric requires preferred routing to a backup data center when the primary hub withdraws a prefix.
Create distinct service VPN membership and scoped data and control policies for the two traffic classes. This would help with a different network situation: A policy intends to keep hospital telemetry isolated from guest browsing even though both use the same internet circuit.
The team applies this planned Catalyst SD-WAN change: Configure VRRP on appropriate service-side interfaces with intended priority and tracking behavior. The original case is: Two branch Edges face the same user VLAN and need a single virtual default gateway that survives device failure. What observation most directly verifies the intended behavior?
Hosts retain the virtual gateway address when the active Edge is failed in a controlled test. This observable result validates the corrective action: Configure VRRP on appropriate service-side interfaces with intended priority and tracking behavior.
The common template remains identical while each Edge receives the correct site-specific BGP peer. That observation would verify another change: One device template is shared by 200 sites, but only the BGP neighbor address should differ per Edge. The expected result instead is: Hosts retain the virtual gateway address when the active Edge is failed in a controlled test.
After first boot, the Edge discovers the fabric and obtains its assigned configuration through authorized provisioning. That observation would verify another change: A remote branch router arrives with no final configuration and the deployment team wants it to join the fabric without an engineer on site. The expected result instead is: Hosts retain the virtual gateway address when the active Edge is failed in a controlled test.
The OSPF neighbor is full and selected campus prefixes appear in remote OMP route tables. That observation would verify another change: A branch Edge peers with a local OSPF router but its learned campus subnets do not enter the overlay. The expected result instead is: Hosts retain the virtual gateway address when the active Edge is failed in a controlled test.
A network engineer is asked to resolve this SD-WAN issue: A branch design uses overlapping LAN prefixes in two tenants and fears that one shared transport network merges their traffic. What is the most appropriate first configuration or operational step?
Separate tenant LANs into distinct service VPNs while retaining the common transport VPN for the underlay. This is the targeted action for the stated case: A branch design uses overlapping LAN prefixes in two tenants and fears that one shared transport network merges their traffic. The specific technical reason is: Cisco SD-WAN service VPN segmentation separates routing domains across a shared encrypted transport fabric. Verification should demonstrate: The same overlapping prefix is reachable in its intended VPN context without leaking between tenants.
Use Cloud OnRamp for SaaS with appropriate application performance monitoring and local path selection. This would help with a different network situation: Users in several regions report intermittent Microsoft 365 performance despite all branch broadband circuits appearing up.
Examine BFD tunnel sessions and measured loss, latency, and jitter on the affected TLOC pair. This would help with a different network situation: A site has working Controller connections, but an application tunnel stops passing packets when the circuit degrades.
Use the appropriate Multi-Region Fabric inter-region border controls and route policy design. This would help with a different network situation: The enterprise spans three regional fabrics, and an administrator wants to suppress needless routes outside their home region.
An engineer proposes this Catalyst SD-WAN remedy: Apply supported OMP path preferences or TLOC attributes in a scoped centralized control policy. The triggering scenario is: A regional fabric requires preferred routing to a backup data center when the primary hub withdraws a prefix. Which underlying SD-WAN behavior BEST explains the response?
Control policies modify distributed OMP routes and transport attributes to influence routing decisions. This technical mechanism explains why the recommended action works: Apply supported OMP path preferences or TLOC attributes in a scoped centralized control policy. A successful deployment should show: The backup advertisement becomes the selected path only after the preferred hub route is withdrawn.
Central control policies can explicitly reject or accept matched OMP routing updates. This principle is associated more closely with another situation: An SD-WAN Controller accepts an OMP route from an untrusted segment, exposing it to unrelated branch sites.
End-to-end segmentation needs consistent VPN definition, service interfaces and routed membership. This principle is associated more closely with another situation: A cloud branch is assigned to a new customer VPN but the Controller continues to distribute only the default service VPN.
Central control policy application uses site and VPN context to constrain overlay route treatment. This principle is associated more closely with another situation: A policy author creates a list of branch sites but mistakenly applies it without matching the intended VPN.
or Guarantee your success by buying the full version which covers the full latest pool of questions. (480 Questions, Last Updated on Nov 11, 2026)
Please check your mailbox for a message from support@examlabs.com and follow the directions.