Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 12

Question 110

Before changing configuration at Northshore Utilities, an engineer investigates: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. Which first diagnostic most directly tests the suspected cause?

  1. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.
  2. Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.
  3. Compare `show ospf database` and LSA sequence/age for the exact origin across the neighboring routers and check adjacency database-exchange states.
  4. Inspect OSPF area interface membership, neighbor area expectations and area-specific database information before tuning route preference.

Correct answer: A

Explanation of each choice

A.

Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies. The reported failure arises during neighbor discovery and adjacency formation, not the subsequent SPF metric ranking of established routes.

B.

The check diagnoses a different layer of service. Its source issue is: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. The relevant initial check is: Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.

C.

This check may help with another root cause, for example: A topology change appears on one router's LSDB but not another's despite successful neighbor Hellos and identical advertised areas. It does not test the first failed condition; start with: Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.

D.

That evidence could be normal while the reported defect persists. It is aimed at: After adding a second OSPF area, a service prefix appears on the wrong area-facing interface and downstream reachability is intermittent. Instead inspect: Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.

Question 111

At Canal City University, a service provider router shows this failure: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. What is the best targeted configuration or operations action?

  1. Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.
  2. Correct the relevant OSPF interface metric values and verify the resulting path costs and SPF next-hop choice.
  3. Align the OSPF Hello and dead interval settings and other required adjacency parameters on both ends of the directly connected link.
  4. Place the logical interface in the intended OSPF area with correct network type and verify the ABR design and necessary route advertisement.

Correct answer: A

Explanation of each choice

A.

Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required. The case-specific reason is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity. A direct acceptance test is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

B.

This action may apply to a different problem, for example: A bandwidth upgrade does not change OSPF path selection because configured interface costs still favor the legacy circuit. It does not repair the stated failure boundary. The case-specific reason is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

C.

The other action is relevant when Two routers share an Ethernet segment and can exchange pings but never form an OSPF adjacency; their configured Hello/dead timers differ. The current case instead requires: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required. The distinction is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

That would address a separate configuration fault: An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. This stem identifies a different cause, corrected by: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

Question 112

A change auditor at Canal City University must validate remediation of this finding: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. Which test outcome is the strongest acceptance evidence?

  1. Approved external prefixes are originated with the correct external attributes and prohibited ones are absent from the neighbor LSDB.
  2. The peers pass database-description exchange without MTU-related resets, reach Full and exchange the expected LSDB information.
  3. The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.
  4. Expected interarea or external reachability appears with the appropriate LSA origin and type, while area-local topology LSAs remain scoped correctly.

Correct answer: C

Explanation of each choice

A.

That check proves something else, such as: An OSPF edge imports an unintended static customer route as an external advertisement after a broad export-policy change. It could pass while the stated problem remains. The targeted evidence here is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

B.

This would be valid for another situation: A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. It does not establish that the failing boundary in this scenario works; verify: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

C.

The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes. Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

That check proves something else, such as: A team is attempting to trace redistributed external routes but checks only router and network LSAs inside the local area. It could pass while the stated problem remains. The targeted evidence here is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

Question 113

The operations training team at Canal City University discusses this issue: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. Which technical explanation matches the intended correction?

  1. OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.
  2. OSPF database description negotiation uses interface MTU information, and a mismatch can stall adjacency even after Hello-based discovery.
  3. Different OSPF LSA types describe router links, multiaccess networks, interarea summaries and redistributed external destinations.
  4. OSPF Hello parameters must match across neighbors for adjacency formation; IP reachability alone does not establish an OSPF relationship.

Correct answer: A

Explanation of each choice

A.

OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering. The key distinction is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity. Accordingly the remedy is: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

B.

That principle belongs to a different service stage: A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. The directly relevant mechanism is: OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.

C.

This explains a separate protocol behavior: A downstream area does not learn an interarea network after an ABR policy change, and staff mistake network LSAs for summary propagation. In the current facts, the controlling mechanism is: OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.

D.

The statement can be true when An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. But it does not explain the reported failure. Here: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

Question 114

At Canal City University, a service acceptance review considers the unresolved issue: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. Which operational exposure follows most directly?

  1. The router can calculate a path from incomplete or stale link-state information, creating asymmetric reachability or loops during convergence.
  2. Area misassignment can isolate subnets or produce misleading LSDB topology even when Layer 3 interfaces remain reachable.
  3. Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.
  4. Routing state may fail to synchronize across the link, leaving expected prefixes unreachable despite basic link-level connectivity.

Correct answer: C

Explanation of each choice

A.

The concern could occur elsewhere when An area has stable OSPF neighbors but one router computes an unexpected path because its LSDB is missing a current advertisement. For the stated scenario, the immediate risk is: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

B.

That consequence is more closely associated with another deficiency, such as: An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. The described fault instead exposes: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

C.

Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence. The direct mitigation is: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

D.

The concern could occur elsewhere when A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. For the stated scenario, the immediate risk is: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

Question 115

Before changing configuration at Canal City University, an engineer investigates: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. Which first diagnostic most directly tests the suspected cause?

  1. Inspect OSPF area interface membership, neighbor area expectations and area-specific database information before tuning route preference.
  2. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.
  3. Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.
  4. Inspect neighbor states, DD packet MTU fields and both logical/physical interface MTU settings before trying authentication or policy changes.

Correct answer: C

Explanation of each choice

A.

This check may help with another root cause, for example: After adding a second OSPF area, a service prefix appears on the wrong area-facing interface and downstream reachability is intermittent. It does not test the first failed condition; start with: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

B.

That evidence could be normal while the reported defect persists. It is aimed at: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. Instead inspect: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

C.

Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy. Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

This check may help with another root cause, for example: A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. It does not test the first failed condition; start with: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

Question 116

During a Junos network change at Maple Coast Retail, the engineer observes: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. Which remediation most directly fixes the described problem?

  1. Place the logical interface in the intended OSPF area with correct network type and verify the ABR design and necessary route advertisement.
  2. Inspect the relevant router, network, summary, and external LSA types and repair the correct ABR or ASBR advertisement scope.
  3. Tighten and validate the Junos OSPF export policy for the exact allowed and denied prefixes and the intended redistribution source.
  4. Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

Correct answer: D

Explanation of each choice

A.

The other action is relevant when An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. The current case instead requires: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required. The distinction is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

B.

That would address a separate configuration fault: A downstream area does not learn an interarea network after an ABR policy change, and staff mistake network LSAs for summary propagation. This stem identifies a different cause, corrected by: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

C.

This action may apply to a different problem, for example: A redistribution policy suppresses one approved connected network, while operators attempt to fix the route with interface metric changes. It does not repair the stated failure boundary. The case-specific reason is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required. The case-specific reason is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity. A direct acceptance test is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

Question 117

The Junos team at Maple Coast Retail needs a success criterion for this defect: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. Which observed result most precisely confirms the intended repair?

  1. Expected interarea or external reachability appears with the appropriate LSA origin and type, while area-local topology LSAs remain scoped correctly.
  2. The selected route has the intended lower accumulated OSPF cost, and path verification confirms traffic follows the preferred link after convergence.
  3. The two peers exchange compatible Hellos, progress to a stable Full adjacency when appropriate, and advertise expected routes without repeated adjacency resets.
  4. The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

Correct answer: D

Explanation of each choice

A.

The observation confirms a different component's behavior. Its source context is: A team is attempting to trace redistributed external routes but checks only router and network LSAs inside the local area. In this case the success criterion is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

B.

That check proves something else, such as: Traffic prefers a slow OSPF path despite a faster link because manual interface costs reverse the intended SPF ranking. It could pass while the stated problem remains. The targeted evidence here is: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

C.

This would be valid for another situation: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. It does not establish that the failing boundary in this scenario works; verify: The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.

D.

The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes. Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

Question 118

While analyzing a service failure at Maple Coast Retail, the following is observed: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.
  2. OSPF Hello parameters must match across neighbors for adjacency formation; IP reachability alone does not establish an OSPF relationship.
  3. OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.
  4. OSPF Hello packets discover neighbors; DD packets summarize LSDBs; requests, updates and acknowledgments reconcile link-state contents.

Correct answer: A

Explanation of each choice

A.

OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering. The key distinction is: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity. Accordingly the remedy is: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

B.

The statement can be true when Two routers share an Ethernet segment and can exchange pings but never form an OSPF adjacency; their configured Hello/dead timers differ. But it does not explain the reported failure. Here: Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

C.

That principle belongs to a different service stage: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. The directly relevant mechanism is: OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.

D.

This explains a separate protocol behavior: A neighbor reaches ExStart and repeatedly restarts database exchange because control-plane packet handling differs across the two ends. In the current facts, the controlling mechanism is: OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.

Question 119

The following provider defect remains uncorrected at Maple Coast Retail: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. What is the most direct service or security risk of leaving it unresolved?

  1. The team can diagnose the wrong flood scope and either miss external reachability or leak a route where it was not intended.
  2. Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.
  3. Neighbors can remain stalled before Full and fail to learn necessary topology even while periodic Hello packets are visible.
  4. The control-plane adjacency never stabilizes, leaving reachability dependent on stale or alternate routes despite a functioning physical link.

Correct answer: B

Explanation of each choice

A.

It is a risk in another topology or protocol state: A team is attempting to trace redistributed external routes but checks only router and network LSAs inside the local area. Here the most direct failure path is: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

B.

Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence. The direct mitigation is: Assign a unique stable OSPF Router ID to each router and carefully restart the relevant protocol process in the approved maintenance window if required.

C.

That consequence is more closely associated with another deficiency, such as: An operator sees Hello packets and assumes OSPF LSAs have been synchronized; database-description and request traffic never completes. The described fault instead exposes: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

D.

It is a risk in another topology or protocol state: Two routers share an Ethernet segment and can exchange pings but never form an OSPF adjacency; their configured Hello/dead timers differ. Here the most direct failure path is: Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.

Question 120

A support escalation at Maple Coast Retail describes: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. Where should the Junos operator look first for decisive evidence?

  1. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.
  2. Inspect neighbor states, DD packet MTU fields and both logical/physical interface MTU settings before trying authentication or policy changes.
  3. Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.
  4. Capture OSPF protocol packet types and compare neighbor state transitions, focusing on DD sequence and link-state request/update progress.

Correct answer: C

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. The relevant initial check is: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

B.

This check may help with another root cause, for example: A point-to-point OSPF link remains in ExStart after a transport migration changed the effective interface MTU, while IPv4 pings still succeed. It does not test the first failed condition; start with: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

C.

Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy. Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

The check diagnoses a different layer of service. Its source issue is: A neighbor reaches ExStart and repeatedly restarts database exchange because control-plane packet handling differs across the two ends. The relevant initial check is: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports