Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 13

Question 120

A support escalation at Maple Coast Retail describes: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. Where should the Junos operator look first for decisive evidence?

  1. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.
  2. Inspect neighbor states, DD packet MTU fields and both logical/physical interface MTU settings before trying authentication or policy changes.
  3. Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.
  4. Capture OSPF protocol packet types and compare neighbor state transitions, focusing on DD sequence and link-state request/update progress.

Correct answer: C

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. The relevant initial check is: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

B.

This check may help with another root cause, for example: A point-to-point OSPF link remains in ExStart after a transport migration changed the effective interface MTU, while IPv4 pings still succeed. It does not test the first failed condition; start with: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

C.

Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy. Router-ID uniqueness is a link-state identity requirement; changing dead timers does not resolve duplicate identity.

D.

The check diagnoses a different layer of service. Its source issue is: A neighbor reaches ExStart and repeatedly restarts database exchange because control-plane packet handling differs across the two ends. The relevant initial check is: Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.

Question 121

During a Junos network change at Cedar Coast Telecom, the engineer observes: On a broadcast multiaccess segment, engineers expect every pair of routers to form Full adjacencies and incorrectly diagnose normal two-way states. Which remediation most directly fixes the described problem?

  1. Align the OSPF Hello and dead interval settings and other required adjacency parameters on both ends of the directly connected link.
  2. Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.
  3. Check LSDB synchronization and required LSA flooding within the affected area, repairing the source or adjacency problem responsible for stale advertisements.
  4. Place the logical interface in the intended OSPF area with correct network type and verify the ABR design and necessary route advertisement.

Correct answer: B

Explanation of each choice

A.

This action may apply to a different problem, for example: Two routers share an Ethernet segment and can exchange pings but never form an OSPF adjacency; their configured Hello/dead timers differ. It does not repair the stated failure boundary. The case-specific reason is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

B.

Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required. The case-specific reason is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full. A direct acceptance test is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

C.

That would address a separate configuration fault: An area has stable OSPF neighbors but one router computes an unexpected path because its LSDB is missing a current advertisement. This stem identifies a different cause, corrected by: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

D.

This action may apply to a different problem, for example: An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. It does not repair the stated failure boundary. The case-specific reason is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

Question 122

The Junos team at Cedar Coast Telecom needs a success criterion for this defect: On a broadcast multiaccess segment, engineers expect every pair of routers to form Full adjacencies and incorrectly diagnose normal two-way states. Which observed result most precisely confirms the intended repair?

  1. Approved external prefixes are originated with the correct external attributes and prohibited ones are absent from the neighbor LSDB.
  2. The selected route has the intended lower accumulated OSPF cost, and path verification confirms traffic follows the preferred link after convergence.
  3. Area routers hold consistent, current relevant LSAs and compute next hops consistent with the corrected topology after SPF runs.
  4. One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

Correct answer: D

Explanation of each choice

A.

This would be valid for another situation: An OSPF edge imports an unintended static customer route as an external advertisement after a broad export-policy change. It does not establish that the failing boundary in this scenario works; verify: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

B.

The observation confirms a different component's behavior. Its source context is: A bandwidth upgrade does not change OSPF path selection because configured interface costs still favor the legacy circuit. In this case the success criterion is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

C.

That check proves something else, such as: An area has stable OSPF neighbors but one router computes an unexpected path because its LSDB is missing a current advertisement. It could pass while the stated problem remains. The targeted evidence here is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

D.

One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented. Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

Question 123

While analyzing a service failure at Cedar Coast Telecom, the following is observed: On a broadcast multiaccess segment, engineers expect every pair of routers to form Full adjacencies and incorrectly diagnose normal two-way states. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. Different OSPF LSA types describe router links, multiaccess networks, interarea summaries and redistributed external destinations.
  2. OSPF uses a logical 32-bit Router ID to identify LSA originators and adjacency participants, independent of physical interface address numbering.
  3. OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.
  4. OSPF areas scope LSDB flooding and use area border routers to exchange reachability between distinct area topologies.

Correct answer: C

Explanation of each choice

A.

That principle belongs to a different service stage: A downstream area does not learn an interarea network after an ABR policy change, and staff mistake network LSAs for summary propagation. The directly relevant mechanism is: OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

B.

This explains a separate protocol behavior: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. In the current facts, the controlling mechanism is: OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

C.

OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins. The key distinction is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full. Accordingly the remedy is: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

D.

That principle belongs to a different service stage: An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. The directly relevant mechanism is: OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

Question 124

The following provider defect remains uncorrected at Cedar Coast Telecom: On a broadcast multiaccess segment, engineers expect every pair of routers to form Full adjacencies and incorrectly diagnose normal two-way states. What is the most direct service or security risk of leaving it unresolved?

  1. Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.
  2. Neighbors can remain stalled before Full and fail to learn necessary topology even while periodic Hello packets are visible.
  3. Traffic can stay on a congested or expensive path even though links and adjacencies are healthy.
  4. The router can calculate a path from incomplete or stale link-state information, creating asymmetric reachability or loops during convergence.

Correct answer: A

Explanation of each choice

A.

Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition. The direct mitigation is: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

B.

It is a risk in another topology or protocol state: An operator sees Hello packets and assumes OSPF LSAs have been synchronized; database-description and request traffic never completes. Here the most direct failure path is: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

C.

The concern could occur elsewhere when Traffic prefers a slow OSPF path despite a faster link because manual interface costs reverse the intended SPF ranking. For the stated scenario, the immediate risk is: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

D.

That consequence is more closely associated with another deficiency, such as: A topology change appears on one router's LSDB but not another's despite successful neighbor Hellos and identical advertised areas. The described fault instead exposes: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

Question 125

A support escalation at Cedar Coast Telecom describes: On a broadcast multiaccess segment, engineers expect every pair of routers to form Full adjacencies and incorrectly diagnose normal two-way states. Where should the Junos operator look first for decisive evidence?

  1. Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.
  2. Capture OSPF protocol packet types and compare neighbor state transitions, focusing on DD sequence and link-state request/update progress.
  3. Inspect OSPF area interface membership, neighbor area expectations and area-specific database information before tuning route preference.
  4. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.

Correct answer: A

Explanation of each choice

A.

Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count. Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

B.

The check diagnoses a different layer of service. Its source issue is: An operator sees Hello packets and assumes OSPF LSAs have been synchronized; database-description and request traffic never completes. The relevant initial check is: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

C.

This check may help with another root cause, for example: After adding a second OSPF area, a service prefix appears on the wrong area-facing interface and downstream reachability is intermittent. It does not test the first failed condition; start with: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

D.

That evidence could be normal while the reported defect persists. It is aimed at: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. Instead inspect: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

Question 126

The provider operations team at ValleyCross Fiber reports: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. Which implementation decision best corrects the cause?

  1. Place the logical interface in the intended OSPF area with correct network type and verify the ABR design and necessary route advertisement.
  2. Identify and correct the actual MTU or adjacency negotiation mismatch on the participating interfaces while keeping necessary link encapsulation consistent.
  3. Correct the relevant OSPF interface metric values and verify the resulting path costs and SPF next-hop choice.
  4. Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

Correct answer: D

Explanation of each choice

A.

That would address a separate configuration fault: An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. This stem identifies a different cause, corrected by: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

B.

This action may apply to a different problem, for example: A point-to-point OSPF link remains in ExStart after a transport migration changed the effective interface MTU, while IPv4 pings still succeed. It does not repair the stated failure boundary. The case-specific reason is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

C.

The other action is relevant when A bandwidth upgrade does not change OSPF path selection because configured interface costs still favor the legacy circuit. The current case instead requires: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required. The distinction is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

D.

Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required. The case-specific reason is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full. A direct acceptance test is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

Question 127

During a post-change check at ValleyCross Fiber, the original condition was: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. What evidence would validate the corrected behavior?

  1. One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.
  2. The neighboring LSDB contains unique router-LSA origins, adjacencies converge and the configured router identity persists across interface changes.
  3. The two peers exchange compatible Hellos, progress to a stable Full adjacency when appropriate, and advertise expected routes without repeated adjacency resets.
  4. Expected interarea or external reachability appears with the appropriate LSA origin and type, while area-local topology LSAs remain scoped correctly.

Correct answer: A

Explanation of each choice

A.

One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented. Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

B.

The observation confirms a different component's behavior. Its source context is: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. In this case the success criterion is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

C.

The observation confirms a different component's behavior. Its source context is: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. In this case the success criterion is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

D.

That check proves something else, such as: A downstream area does not learn an interarea network after an ABR policy change, and staff mistake network LSAs for summary propagation. It could pass while the stated problem remains. The targeted evidence here is: One DR and one BDR are elected as designed; non-DR peer states and adjacency topology match broadcast OSPF behavior, with approved router priorities documented.

Question 128

At ValleyCross Fiber, an engineer is asked to explain this case: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. Which underlying routing or switching principle accounts for the appropriate solution?

  1. OSPF areas scope LSDB flooding and use area border routers to exchange reachability between distinct area topologies.
  2. OSPF derives SPF paths from its area LSDB; Hellos alone do not prove that database exchange and flooding completed correctly.
  3. OSPF Hello parameters must match across neighbors for adjacency formation; IP reachability alone does not establish an OSPF relationship.
  4. OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

Correct answer: D

Explanation of each choice

A.

The statement can be true when An interface moved to a new routing zone still participates in its former OSPF area despite updated IP addressing. But it does not explain the reported failure. Here: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

B.

That principle belongs to a different service stage: An area has stable OSPF neighbors but one router computes an unexpected path because its LSDB is missing a current advertisement. The directly relevant mechanism is: OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

C.

This explains a separate protocol behavior: An OSPF peer alternates between down and init after an interface migration while packet captures reveal Hello parameters inconsistent on the two ends. In the current facts, the controlling mechanism is: OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins.

D.

OSPF elects DR/BDR on multiaccess media to limit full adjacency and flooding complexity; elections are not automatically preemptive when a higher-priority router joins. The key distinction is: Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full. Accordingly the remedy is: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

Question 129

A risk assessment at ValleyCross Fiber identifies: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. Which practical consequence is most specifically tied to this failure?

  1. Routing state may fail to synchronize across the link, leaving expected prefixes unreachable despite basic link-level connectivity.
  2. Duplicate protocol identities can corrupt LSDB origin assumptions and prevent predictable route computation or neighbor convergence.
  3. An overly broad export rule can leak internal routes, while a missing accept term can withhold legitimate external reachability.
  4. Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

Correct answer: D

Explanation of each choice

A.

The concern could occur elsewhere when A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. For the stated scenario, the immediate risk is: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

B.

That consequence is more closely associated with another deficiency, such as: An OSPF router unexpectedly uses a duplicate Router ID after a staged configuration copy and one neighbor refuses to establish correct database synchronization. The described fault instead exposes: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

C.

It is a risk in another topology or protocol state: A redistribution policy suppresses one approved connected network, while operators attempt to fix the route with interface metric changes. Here the most direct failure path is: Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition.

D.

Misinterpreting normal two-way neighbors can trigger unnecessary outages or lead to an improperly managed DR transition. The direct mitigation is: Verify the broadcast-network DR/BDR roles and adjacency expectations, and plan a controlled election transition if a DR change is required.

Question 130

The on-call engineer at ValleyCross Fiber receives this fault report: A newly attached router with high priority fails to preempt an existing designated router, and the design team assumes priority alone forces immediate re-election. What initial check best isolates the actual failing protocol stage?

  1. Inspect neighbor states, DD packet MTU fields and both logical/physical interface MTU settings before trying authentication or policy changes.
  2. Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.
  3. Inspect local and neighbor router IDs plus conflicting LSA originators before modifying OSPF interface cost or routing policy.
  4. Compare `show ospf neighbor` with both interfaces' configured timers and a Hello packet capture before changing routing import policies.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: A new OSPF neighbor oscillates between Exchange and ExStart when a carrier's encapsulation overhead makes the two ends advertise different allowable packet sizes. It does not test the first failed condition; start with: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

B.

Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count. Broadcast OSPF has deliberate DR/BDR adjacency rules, unlike point-to-point networks where all established peers typically reach Full.

C.

The check diagnoses a different layer of service. Its source issue is: A dual-homed router has inconsistent OSPF identity following a replacement Routing Engine, with LSDB conflicts despite working interface IP addresses. The relevant initial check is: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

D.

This check may help with another root cause, for example: Two routers share an Ethernet segment and can exchange pings but never form an OSPF adjacency; their configured Hello/dead timers differ. It does not test the first failed condition; start with: Use neighbor detail and interface election output to identify current DR/BDR, priorities and eligible adjacencies rather than judging only Full state count.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports