Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 23

Question 220

During provider troubleshooting at Clearwater Analytics, this symptom is observed: Two IS-IS devices have matching area identifiers but the configured interface level and authentication parameters prevent Hello acceptance. Which targeted inspection should precede remediation?

  1. Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.
  2. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  3. Check each router's NET/area and IS-IS level capabilities, plus adjacency level and Level 2 route presence.
  4. Inspect level-specific import/export policy and L1 versus L2 routes for the exact prefix before changing interface metric values.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. It does not test the first failed condition; start with: Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.

B.

Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement. A functioning IP interface does not establish IS-IS neighbor compatibility; IIH acceptance is the first control-plane gate.

C.

The check diagnoses a different layer of service. Its source issue is: A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. The relevant initial check is: Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.

D.

This check may help with another root cause, for example: A Level 1 branch needs a selected prefix from Level 2 but a restrictive policy leaves it unaware of the destination. It does not test the first failed condition; start with: Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.

Question 221

A production change request at Crestpoint Research includes this finding: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. What should the engineer change to address it?

  1. Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.
  2. Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.
  3. Align the IS-IS interface activation, circuit level and required authentication, and confirm valid IIH exchanges on both ends.
  4. Implement a narrowly scoped IS-IS interlevel route-leaking policy and validate that selected prefixes are advertised in the intended area and level.

Correct answer: A

Explanation of each choice

A.

Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization. A direct acceptance test is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

B.

This action may apply to a different problem, for example: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. It does not repair the stated failure boundary. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

C.

This action may apply to a different problem, for example: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. It does not repair the stated failure boundary. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

D.

The other action is relevant when An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. The current case instead requires: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap. The distinction is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

Question 222

After Crestpoint Research applies its proposed fix to this problem — A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. — which observation best proves the specific failure has been resolved?

  1. The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.
  2. One appropriate DIS is elected with the expected pseudonode LSP, and level-specific LAN neighbors synchronize correctly.
  3. The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.
  4. Advertised extended reachability metrics match the design and SPF selects the expected lower-cost path without metric truncation.

Correct answer: C

Explanation of each choice

A.

The observation confirms a different component's behavior. Its source context is: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. In this case the success criterion is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

B.

That check proves something else, such as: A new higher-priority router joins an IS-IS LAN but the team expects OSPF's DR/BDR rules and cannot explain the pseudonode origin. It could pass while the stated problem remains. The targeted evidence here is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

C.

The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology. Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

D.

The observation confirms a different component's behavior. Its source context is: An IS-IS design uses extended metrics on some routers but a legacy metric setting prevents uniform interpretation of path cost. In this case the success criterion is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

Question 223

An architecture review at Crestpoint Research examines the following symptom: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. What Junos or protocol mechanism is most directly responsible?

  1. IS-IS route leaking intentionally advertises selected reachability between Level 2 and Level 1 rather than treating all interarea prefixes as native L1 routes.
  2. IS-IS extended/wide metrics permit larger link cost values and are carried in suitable reachability TLVs; all participating speakers must interpret them consistently.
  3. IS-IS uses Level 1 for intra-area routing and Level 2 for interarea routing; area matching rules differ by adjacency level.
  4. IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

Correct answer: D

Explanation of each choice

A.

This explains a separate protocol behavior: A Level 1 branch needs a selected prefix from Level 2 but a restrictive policy leaves it unaware of the destination. In the current facts, the controlling mechanism is: IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

B.

The statement can be true when An IS-IS design uses extended metrics on some routers but a legacy metric setting prevents uniform interpretation of path cost. But it does not explain the reported failure. Here: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

C.

That principle belongs to a different service stage: Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. The directly relevant mechanism is: IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

D.

IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB. The key distinction is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization. Accordingly the remedy is: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.

Question 224

The team at Crestpoint Research defers a fix for this condition: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. What failure is most likely if no targeted control is applied?

  1. Missing source routes isolate services, while a broad export can introduce undesirable extra prefixes into the domain.
  2. Path selection may not reflect network engineering intent or can lose reachability across mixed metric deployments.
  3. The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.
  4. A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

Correct answer: D

Explanation of each choice

A.

It is a risk in another topology or protocol state: A connected service subnet must be injected into IS-IS but is absent even though the router's connected route is active. Here the most direct failure path is: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

B.

The concern could occur elsewhere when An IS-IS design uses extended metrics on some routers but a legacy metric setting prevents uniform interpretation of path cost. For the stated scenario, the immediate risk is: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

C.

That consequence is more closely associated with another deficiency, such as: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. The described fault instead exposes: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

D.

A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up. The direct mitigation is: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.

Question 225

During provider troubleshooting at Crestpoint Research, this symptom is observed: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. Which targeted inspection should precede remediation?

  1. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  2. Inspect level-specific import/export policy and L1 versus L2 routes for the exact prefix before changing interface metric values.
  3. Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.
  4. Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

Correct answer: C

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. The relevant initial check is: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

B.

This check may help with another root cause, for example: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. It does not test the first failed condition; start with: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

C.

Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors. Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

D.

The check diagnoses a different layer of service. Its source issue is: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. The relevant initial check is: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

Question 226

At Atlas Port Services, a service provider router shows this failure: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. What is the best targeted configuration or operations action?

  1. Check IS-IS LAN priority/system identifiers and verify the correct DIS and pseudonode LSP behavior on that shared segment.
  2. Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.
  3. Implement a narrowly scoped IS-IS interlevel route-leaking policy and validate that selected prefixes are advertised in the intended area and level.
  4. Enable consistent wide-metric support and configure the intended IS-IS interface metrics across participating routers.

Correct answer: B

Explanation of each choice

A.

This action may apply to a different problem, for example: A new higher-priority router joins an IS-IS LAN but the team expects OSPF's DR/BDR rules and cannot explain the pseudonode origin. It does not repair the stated failure boundary. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

B.

Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization. A direct acceptance test is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

C.

That would address a separate configuration fault: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. This stem identifies a different cause, corrected by: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.

D.

This action may apply to a different problem, for example: A new high-capacity transit link stays unattractive in IS-IS despite the physical upgrade because an oversized intended metric cannot be represented in the current metric style. It does not repair the stated failure boundary. The case-specific reason is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

Question 227

A change auditor at Atlas Port Services must validate remediation of this finding: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Which test outcome is the strongest acceptance evidence?

  1. Advertised extended reachability metrics match the design and SPF selects the expected lower-cost path without metric truncation.
  2. IS-IS adjacency moves to Up at the intended level with matching system IDs and Hello acceptance, followed by expected reachability.
  3. The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.
  4. Level 1 neighbors share the intended area identity and Level 2 adjacencies form where required, with valid routes available beyond each local area.

Correct answer: C

Explanation of each choice

A.

This would be valid for another situation: An IS-IS design uses extended metrics on some routers but a legacy metric setting prevents uniform interpretation of path cost. It does not establish that the failing boundary in this scenario works; verify: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

B.

The observation confirms a different component's behavior. Its source context is: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. In this case the success criterion is: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

C.

The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology. Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

D.

This would be valid for another situation: Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. It does not establish that the failing boundary in this scenario works; verify: The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.

Question 228

The operations training team at Atlas Port Services discusses this issue: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Which technical explanation matches the intended correction?

  1. The IS-IS designated intermediate system represents the shared LAN as a pseudonode; it is not an OSPF DR/BDR pair.
  2. IS-IS uses Level 1 for intra-area routing and Level 2 for interarea routing; area matching rules differ by adjacency level.
  3. IS-IS Hello PDUs establish neighbor relationships using circuit parameters and level/authentication compatibility rather than IP neighbor discovery alone.
  4. IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

Correct answer: D

Explanation of each choice

A.

That principle belongs to a different service stage: A new higher-priority router joins an IS-IS LAN but the team expects OSPF's DR/BDR rules and cannot explain the pseudonode origin. The directly relevant mechanism is: IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

B.

This explains a separate protocol behavior: Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. In the current facts, the controlling mechanism is: IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

C.

The statement can be true when Two IS-IS devices have matching area identifiers but the configured interface level and authentication parameters prevent Hello acceptance. But it does not explain the reported failure. Here: Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

D.

IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB. The key distinction is: Consistent Hello status is necessary but insufficient to prove LSP database synchronization. Accordingly the remedy is: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.

Question 229

At Atlas Port Services, a service acceptance review considers the unresolved issue: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Which operational exposure follows most directly?

  1. A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.
  2. The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.
  3. Overly broad leaking bloats a constrained L1 area or exposes route reachability contrary to the topology plan.
  4. Incorrect assumptions about DIS operation can hide LAN topology problems or prompt destabilizing changes to a working adjacency.

Correct answer: A

Explanation of each choice

A.

A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up. The direct mitigation is: Trace IS-IS LSP flooding and database synchronization at the affected level, correcting the propagation or adjacency gap.

B.

It is a risk in another topology or protocol state: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. Here the most direct failure path is: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

C.

The concern could occur elsewhere when An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. For the stated scenario, the immediate risk is: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

D.

That consequence is more closely associated with another deficiency, such as: Routers on an IS-IS broadcast LAN show a different designated intermediate system than the operations diagram predicts. The described fault instead exposes: A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.

Question 230

Before changing configuration at Atlas Port Services, an engineer investigates: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Which first diagnostic most directly tests the suspected cause?

  1. Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.
  2. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  3. Inspect level-specific import/export policy and L1 versus L2 routes for the exact prefix before changing interface metric values.
  4. Inspect configured metric styles, LSP reachability TLVs and computed route costs at the same IS-IS level.

Correct answer: A

Explanation of each choice

A.

Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors. Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

B.

The check diagnoses a different layer of service. Its source issue is: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. The relevant initial check is: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

C.

This check may help with another root cause, for example: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. It does not test the first failed condition; start with: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

D.

That evidence could be normal while the reported defect persists. It is aimed at: A new high-capacity transit link stays unattractive in IS-IS despite the physical upgrade because an oversized intended metric cannot be represented in the current metric style. Instead inspect: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports