Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 24

Question 230

Before changing configuration at Atlas Port Services, an engineer investigates: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Which first diagnostic most directly tests the suspected cause?

  1. Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.
  2. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  3. Inspect level-specific import/export policy and L1 versus L2 routes for the exact prefix before changing interface metric values.
  4. Inspect configured metric styles, LSP reachability TLVs and computed route costs at the same IS-IS level.

Correct answer: A

Explanation of each choice

A.

Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors. Consistent Hello status is necessary but insufficient to prove LSP database synchronization.

B.

The check diagnoses a different layer of service. Its source issue is: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. The relevant initial check is: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

C.

This check may help with another root cause, for example: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. It does not test the first failed condition; start with: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

D.

That evidence could be normal while the reported defect persists. It is aimed at: A new high-capacity transit link stays unattractive in IS-IS despite the physical upgrade because an oversized intended metric cannot be represented in the current metric style. Instead inspect: Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.

Question 231

At Baystone Energy, a service provider router shows this failure: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. What is the best targeted configuration or operations action?

  1. Enable consistent wide-metric support and configure the intended IS-IS interface metrics across participating routers.
  2. Collect adjacency state, protocol trace, interface error/MTU information and LSP database comparisons, then correct the component that fails first.
  3. Correct the IS-IS level and area design so Level 1 adjacency occurs only between common-area routers and Level 2 connectivity carries interarea reachability.
  4. Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

Correct answer: D

Explanation of each choice

A.

That would address a separate configuration fault: A new high-capacity transit link stays unattractive in IS-IS despite the physical upgrade because an oversized intended metric cannot be represented in the current metric style. This stem identifies a different cause, corrected by: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

B.

This action may apply to a different problem, for example: A provider cannot decide whether IS-IS is losing Hello packets or receiving LSDB updates but failing to process them. It does not repair the stated failure boundary. The case-specific reason is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

C.

The other action is relevant when Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. The current case instead requires: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation. The distinction is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

D.

Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation. The case-specific reason is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role. A direct acceptance test is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

Question 232

A change auditor at Baystone Energy must validate remediation of this finding: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. Which test outcome is the strongest acceptance evidence?

  1. The relevant LSP identifiers, sequence numbers and contents match among routers at the same level, and SPF reflects the current topology.
  2. The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.
  3. Advertised extended reachability metrics match the design and SPF selects the expected lower-cost path without metric truncation.
  4. The measured first failing state is corrected and neighbor stability, LSP synchronization and resulting routes recover under a repeatable test.

Correct answer: B

Explanation of each choice

A.

That check proves something else, such as: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. It could pass while the stated problem remains. The targeted evidence here is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

B.

The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match. A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

C.

The observation confirms a different component's behavior. Its source context is: A new high-capacity transit link stays unattractive in IS-IS despite the physical upgrade because an oversized intended metric cannot be represented in the current metric style. In this case the success criterion is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

D.

That check proves something else, such as: A provider cannot decide whether IS-IS is losing Hello packets or receiving LSDB updates but failing to process them. It could pass while the stated problem remains. The targeted evidence here is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

Question 233

The operations training team at Baystone Energy discusses this issue: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. Which technical explanation matches the intended correction?

  1. IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.
  2. IS-IS extended/wide metrics permit larger link cost values and are carried in suitable reachability TLVs; all participating speakers must interpret them consistently.
  3. IS-IS uses Level 1 for intra-area routing and Level 2 for interarea routing; area matching rules differ by adjacency level.
  4. IS-IS LSPs encode link-state reachability and are flooded within a level so each participating system calculates from a consistent LSDB.

Correct answer: A

Explanation of each choice

A.

IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct. The key distinction is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role. Accordingly the remedy is: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

B.

That principle belongs to a different service stage: An IS-IS design uses extended metrics on some routers but a legacy metric setting prevents uniform interpretation of path cost. The directly relevant mechanism is: IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.

C.

This explains a separate protocol behavior: Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. In the current facts, the controlling mechanism is: IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.

D.

The statement can be true when An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. But it does not explain the reported failure. Here: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

Question 234

At Baystone Energy, a service acceptance review considers the unresolved issue: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. Which operational exposure follows most directly?

  1. Cross-area prefixes can disappear or traffic can follow an unavailable default when L1/L2 boundaries are incorrectly configured.
  2. The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.
  3. A stale LSDB can cause transient loops, missing reachability and inconsistent path computation even while some adjacencies remain Up.
  4. Missing source routes isolate services, while a broad export can introduce undesirable extra prefixes into the domain.

Correct answer: B

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. The described fault instead exposes: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

B.

The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change. The direct mitigation is: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

C.

It is a risk in another topology or protocol state: A transit core forms stable IS-IS adjacencies but one router's link-state PDU database lacks a refreshed neighbor record. Here the most direct failure path is: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

D.

The concern could occur elsewhere when A policy change accidentally distributes infrastructure static routes into IS-IS and expands the link-state database beyond approved scope. For the stated scenario, the immediate risk is: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

Question 235

Before changing configuration at Baystone Energy, an engineer investigates: A parser discards useful IS-IS reachability information because the team mistakes an extended reachability TLV for a Hello timer field. Which first diagnostic most directly tests the suspected cause?

  1. Check each router's NET/area and IS-IS level capabilities, plus adjacency level and Level 2 route presence.
  2. Compare `show isis database` LSP IDs, sequence values and level-specific flooding status between the affected neighbors.
  3. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  4. Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

Correct answer: D

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. Instead inspect: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

B.

That evidence could be normal while the reported defect persists. It is aimed at: An access-area router continues to calculate an obsolete SPF route because its LSP sequence version differs from adjacent routers after a change. Instead inspect: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

C.

The check diagnoses a different layer of service. Its source issue is: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. The relevant initial check is: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

D.

Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status. A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

Question 236

During a Junos network change at Stonebridge Hospitality, the engineer observes: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. Which remediation most directly fixes the described problem?

  1. Correct the IS-IS level and area design so Level 1 adjacency occurs only between common-area routers and Level 2 connectivity carries interarea reachability.
  2. Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.
  3. Align the IS-IS interface activation, circuit level and required authentication, and confirm valid IIH exchanges on both ends.
  4. Check IS-IS LAN priority/system identifiers and verify the correct DIS and pseudonode LSP behavior on that shared segment.

Correct answer: B

Explanation of each choice

A.

The other action is relevant when A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. The current case instead requires: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation. The distinction is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

B.

Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation. The case-specific reason is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role. A direct acceptance test is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

C.

This action may apply to a different problem, for example: Two IS-IS devices have matching area identifiers but the configured interface level and authentication parameters prevent Hello acceptance. It does not repair the stated failure boundary. The case-specific reason is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

D.

The other action is relevant when Routers on an IS-IS broadcast LAN show a different designated intermediate system than the operations diagram predicts. The current case instead requires: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation. The distinction is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

Question 237

The Junos team at Stonebridge Hospitality needs a success criterion for this defect: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. Which observed result most precisely confirms the intended repair?

  1. The measured first failing state is corrected and neighbor stability, LSP synchronization and resulting routes recover under a repeatable test.
  2. The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.
  3. Only approved interlevel prefixes appear in the target Level 1 database and route table, preserving reachability without a wholesale route leak.
  4. Level 1 neighbors share the intended area identity and Level 2 adjacencies form where required, with valid routes available beyond each local area.

Correct answer: B

Explanation of each choice

A.

The observation confirms a different component's behavior. Its source context is: A provider cannot decide whether IS-IS is losing Hello packets or receiving LSDB updates but failing to process them. In this case the success criterion is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

B.

The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match. A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

C.

This would be valid for another situation: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. It does not establish that the failing boundary in this scenario works; verify: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

D.

The observation confirms a different component's behavior. Its source context is: Two core routers join different IS-IS areas but are expected to exchange Level 1 routes directly as if they share an area identifier. In this case the success criterion is: The expected neighbor or prefix TLV is present in current LSPs with the intended metric representation, and SPF results match.

Question 238

While analyzing a service failure at Stonebridge Hospitality, the following is observed: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. Which mechanism best explains the underlying control-plane or forwarding behavior?

  1. IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.
  2. IS-IS route leaking intentionally advertises selected reachability between Level 2 and Level 1 rather than treating all interarea prefixes as native L1 routes.
  3. IS-IS uses Level 1 for intra-area routing and Level 2 for interarea routing; area matching rules differ by adjacency level.
  4. IS-IS Hello PDUs establish neighbor relationships using circuit parameters and level/authentication compatibility rather than IP neighbor discovery alone.

Correct answer: A

Explanation of each choice

A.

IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct. The key distinction is: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role. Accordingly the remedy is: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

B.

The statement can be true when A Level 1 branch needs a selected prefix from Level 2 but a restrictive policy leaves it unaware of the destination. But it does not explain the reported failure. Here: A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

C.

This explains a separate protocol behavior: A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. In the current facts, the controlling mechanism is: IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.

D.

This explains a separate protocol behavior: An IS-IS point-to-point peer stays down after interface provisioning while interface counters increment and other routed protocols can use the link. In the current facts, the controlling mechanism is: IS-IS uses structured TLVs inside PDUs to advertise attributes and reachability; metric encodings and PDU purposes are distinct.

Question 239

The following provider defect remains uncorrected at Stonebridge Hospitality: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. What is the most direct service or security risk of leaving it unresolved?

  1. Neighbors cannot exchange link-state packets and the core loses alternative paths during topology changes.
  2. Missing source routes isolate services, while a broad export can introduce undesirable extra prefixes into the domain.
  3. Cross-area prefixes can disappear or traffic can follow an unavailable default when L1/L2 boundaries are incorrectly configured.
  4. The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

Correct answer: D

Explanation of each choice

A.

It is a risk in another topology or protocol state: Two IS-IS devices have matching area identifiers but the configured interface level and authentication parameters prevent Hello acceptance. Here the most direct failure path is: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

B.

The concern could occur elsewhere when A connected service subnet must be injected into IS-IS but is absent even though the router's connected route is active. For the stated scenario, the immediate risk is: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

C.

That consequence is more closely associated with another deficiency, such as: A provider redesigns two areas and loses expected interarea reachability because a border router is no longer participating in Level 2 routing. The described fault instead exposes: The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change.

D.

The network may misinterpret advertisements and calculate a route inconsistent with the intended metric change. The direct mitigation is: Inspect the correct IS-IS PDU and Type-Length-Value carrying the intended reachability or metric information, then align compatible wide-metric operation.

Question 240

A support escalation at Stonebridge Hospitality describes: A provider changes wide metrics in IS-IS but monitoring reads only legacy narrow reachability data and reports no topology effect. Where should the Junos operator look first for decisive evidence?

  1. Inspect level-specific import/export policy and L1 versus L2 routes for the exact prefix before changing interface metric values.
  2. Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.
  3. Inspect `show isis adjacency` and Hello packet details including level, authentication and interface enablement.
  4. Inspect LAN adjacency detail, DIS identity, priorities and pseudonode LSPs at the affected level.

Correct answer: B

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: An operator leaks the entire Level 2 table into a small Level 1 area when only a single approved service prefix was required. The relevant initial check is: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

B.

Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status. A TLV inside an LSP conveys link-state attributes; it is not interchangeable with an IIH PDU's neighbor-discovery role.

C.

That evidence could be normal while the reported defect persists. It is aimed at: Two IS-IS devices have matching area identifiers but the configured interface level and authentication parameters prevent Hello acceptance. Instead inspect: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

D.

The check diagnoses a different layer of service. Its source issue is: Routers on an IS-IS broadcast LAN show a different designated intermediate system than the operations diagram predicts. The relevant initial check is: Inspect the LSP contents and specific reachability TLV type and value at the correct level rather than relying only on generic neighbor status.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports