JN0-364 Premium File
- 69 Questions & Answers
- Last Update: Nov 4, 2026
The on-call engineer at Northshore Utilities receives this fault report: A bridged VLAN experiences unknown-unicast flooding because no valid source MAC entries are learned on the new access interface after a migration. What initial check best isolates the actual failing protocol stage?
That evidence could be normal while the reported defect persists. It is aimed at: An operator moves one customer port into a new virtual-switch service but continues to inspect the global bridge table, missing the tenant-specific entries. Instead inspect: Inspect the MAC address table for the VLAN and customer MAC, port state and aging or movement counters on the service interfaces.
The check diagnoses a different layer of service. Its source issue is: Hosts within a VLAN communicate, but traffic to other VLANs fails because the logical Layer 3 gateway is not linked to the bridge VLAN. The relevant initial check is: Inspect the MAC address table for the VLAN and customer MAC, port state and aging or movement counters on the service interfaces.
Inspect the MAC address table for the VLAN and customer MAC, port state and aging or movement counters on the service interfaces. MAC learning concerns Layer 2 location; changing BGP next hop or IGP metric does not select the correct bridged egress port.
That evidence could be normal while the reported defect persists. It is aimed at: After replacing an edge switch, customer traffic arrives with an unexpected outer tag and the provider places it in the wrong broadcast domain. Instead inspect: Inspect the MAC address table for the VLAN and customer MAC, port state and aging or movement counters on the service interfaces.
The provider operations team at Canal City University reports: A site access port accidentally belongs to the provider management VLAN, so the attached single-VLAN device receives a DHCP address from the wrong segment. Which implementation decision best corrects the cause?
That would address a separate configuration fault: A provider uplink carries VLAN 100 but drops VLAN 200 traffic because the trunk's allowed membership omits VLAN 200. This stem identifies a different cause, corrected by: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
This action may apply to a different problem, for example: A port is in the correct trunk mode yet a service still fails because the corresponding bridge domain does not include the logical unit. It does not repair the stated failure boundary. The case-specific reason is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks. The case-specific reason is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community. A direct acceptance test is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
That would address a separate configuration fault: A bridged VLAN experiences unknown-unicast flooding because no valid source MAC entries are learned on the new access interface after a migration. This stem identifies a different cause, corrected by: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
During a post-change check at Canal City University, the original condition was: A site access port accidentally belongs to the provider management VLAN, so the attached single-VLAN device receives a DHCP address from the wrong segment. What evidence would validate the corrected behavior?
Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain. Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
This would be valid for another situation: A campus-to-provider trunk passes several tagged customer services while a newly provisioned tag fails because the far-end trunk has not allowed it. It does not establish that the failing boundary in this scenario works; verify: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
The observation confirms a different component's behavior. Its source context is: Two wholesale L2 customers use overlapping VLAN identifiers; without separation their Ethernet segments are accidentally bridged together. In this case the success criterion is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
That check proves something else, such as: A migration mixes tagged and untagged handoffs on the same service, and operators cannot explain why traffic falls into an unintended VLAN. It could pass while the stated problem remains. The targeted evidence here is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
At Canal City University, an engineer is asked to explain this case: A site access port accidentally belongs to the provider management VLAN, so the attached single-VLAN device receives a DHCP address from the wrong segment. Which underlying routing or switching principle accounts for the appropriate solution?
The statement can be true when After replacing an edge switch, customer traffic arrives with an unexpected outer tag and the provider places it in the wrong broadcast domain. But it does not explain the reported failure. Here: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
That principle belongs to a different service stage: An upstream customer changes its inner VLAN numbers and the carrier wants to preserve those tags without provisioning each inner VLAN individually. The directly relevant mechanism is: An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport.
This explains a separate protocol behavior: A provider uplink carries VLAN 100 but drops VLAN 200 traffic because the trunk's allowed membership omits VLAN 200. In the current facts, the controlling mechanism is: An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport.
An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport. The key distinction is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community. Accordingly the remedy is: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
A risk assessment at Canal City University identifies: A site access port accidentally belongs to the provider management VLAN, so the attached single-VLAN device receives a DHCP address from the wrong segment. Which practical consequence is most specifically tied to this failure?
The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up. The direct mitigation is: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
That consequence is more closely associated with another deficiency, such as: A port is in the correct trunk mode yet a service still fails because the corresponding bridge domain does not include the logical unit. The described fault instead exposes: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
It is a risk in another topology or protocol state: Hosts within a VLAN communicate, but traffic to other VLANs fails because the logical Layer 3 gateway is not linked to the bridge VLAN. Here the most direct failure path is: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
The concern could occur elsewhere when An operator moves one customer port into a new virtual-switch service but continues to inspect the global bridge table, missing the tenant-specific entries. For the stated scenario, the immediate risk is: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
The on-call engineer at Canal City University receives this fault report: A site access port accidentally belongs to the provider management VLAN, so the attached single-VLAN device receives a DHCP address from the wrong segment. What initial check best isolates the actual failing protocol stage?
This check may help with another root cause, for example: A redundant bridged customer ring floods broadcasts after a link change because the blocking/forwarding boundary is misconfigured. It does not test the first failed condition; start with: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
That evidence could be normal while the reported defect persists. It is aimed at: A migration mixes tagged and untagged handoffs on the same service, and operators cannot explain why traffic falls into an unintended VLAN. Instead inspect: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
The check diagnoses a different layer of service. Its source issue is: A provider uplink carries VLAN 100 but drops VLAN 200 traffic because the trunk's allowed membership omits VLAN 200. The relevant initial check is: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN. Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
A production change request at Maple Coast Retail includes this finding: A customer endpoint sends untagged Ethernet frames but the new interface is configured for the wrong untagged VLAN, preventing communication with its gateway. What should the engineer change to address it?
The other action is relevant when A campus-to-provider trunk passes several tagged customer services while a newly provisioned tag fails because the far-end trunk has not allowed it. The current case instead requires: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks. The distinction is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
That would address a separate configuration fault: After replacing an edge switch, customer traffic arrives with an unexpected outer tag and the provider places it in the wrong broadcast domain. This stem identifies a different cause, corrected by: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks. The case-specific reason is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community. A direct acceptance test is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
The other action is relevant when A carrier must transport a customer's internal VLAN tags across its Metro Ethernet network while isolating each customer service with an outer service tag. The current case instead requires: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks. The distinction is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
After Maple Coast Retail applies its proposed fix to this problem — A customer endpoint sends untagged Ethernet frames but the new interface is configured for the wrong untagged VLAN, preventing communication with its gateway. — which observation best proves the specific failure has been resolved?
The observation confirms a different component's behavior. Its source context is: A migration mixes tagged and untagged handoffs on the same service, and operators cannot explain why traffic falls into an unintended VLAN. In this case the success criterion is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain. Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
This would be valid for another situation: An upstream customer changes its inner VLAN numbers and the carrier wants to preserve those tags without provisioning each inner VLAN individually. It does not establish that the failing boundary in this scenario works; verify: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
The observation confirms a different component's behavior. Its source context is: Hosts within a VLAN communicate, but traffic to other VLANs fails because the logical Layer 3 gateway is not linked to the bridge VLAN. In this case the success criterion is: Untagged traffic is classified into the expected VLAN and the endpoint reaches only the approved gateway and local broadcast domain.
An architecture review at Maple Coast Retail examines the following symptom: A customer endpoint sends untagged Ethernet frames but the new interface is configured for the wrong untagged VLAN, preventing communication with its gateway. What Junos or protocol mechanism is most directly responsible?
This explains a separate protocol behavior: A campus-to-provider trunk passes several tagged customer services while a newly provisioned tag fails because the far-end trunk has not allowed it. In the current facts, the controlling mechanism is: An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport.
The statement can be true when Hosts within a VLAN communicate, but traffic to other VLANs fails because the logical Layer 3 gateway is not linked to the bridge VLAN. But it does not explain the reported failure. Here: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
That principle belongs to a different service stage: A port is in the correct trunk mode yet a service still fails because the corresponding bridge domain does not include the logical unit. The directly relevant mechanism is: An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport.
An access port assigns untagged frames to one configured VLAN and does not ordinarily serve as a multi-VLAN tagged transport. The key distinction is: Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community. Accordingly the remedy is: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
The team at Maple Coast Retail defers a fix for this condition: A customer endpoint sends untagged Ethernet frames but the new interface is configured for the wrong untagged VLAN, preventing communication with its gateway. What failure is most likely if no targeted control is applied?
It is a risk in another topology or protocol state: An upstream customer changes its inner VLAN numbers and the carrier wants to preserve those tags without provisioning each inner VLAN individually. Here the most direct failure path is: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
The concern could occur elsewhere when A provider Ethernet service forwards unicast normally until a customer VM migrates; packets for its MAC continue toward the old attachment port. For the stated scenario, the immediate risk is: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
That consequence is more closely associated with another deficiency, such as: An operator moves one customer port into a new virtual-switch service but continues to inspect the global bridge table, missing the tenant-specific entries. The described fault instead exposes: The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up.
The customer can reach a management segment or become isolated from its actual gateway despite the Ethernet link staying up. The direct mitigation is: Assign the access interface to the intended VLAN and verify untagged ingress/egress membership without enabling unrelated tagged networks.
During provider troubleshooting at Maple Coast Retail, this symptom is observed: A customer endpoint sends untagged Ethernet frames but the new interface is configured for the wrong untagged VLAN, preventing communication with its gateway. Which targeted inspection should precede remediation?
The check diagnoses a different layer of service. Its source issue is: Two provider-facing switchports both forward the same bridged service and the MAC table shows persistent flapping between ports. The relevant initial check is: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN. Untagged ingress classification is controlled by access-port VLAN membership, not by a route-policy community.
That evidence could be normal while the reported defect persists. It is aimed at: A migration mixes tagged and untagged handoffs on the same service, and operators cannot explain why traffic falls into an unintended VLAN. Instead inspect: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
The check diagnoses a different layer of service. Its source issue is: Two wholesale L2 customers use overlapping VLAN identifiers; without separation their Ethernet segments are accidentally bridged together. The relevant initial check is: Inspect interface port mode and VLAN membership, then capture untagged frames and verify the learned MAC in the target VLAN.
Please check your mailbox for a message from support@examlabs.com and follow the directions.