Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 7

Question 60

During provider troubleshooting at Orion Transit Exchange, this symptom is observed: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. Which targeted inspection should precede remediation?

  1. Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.
  2. Inspect the precise prefix in the routing table and the resolved next-hop/forwarding entry, then compare the active static configuration with the working topology.
  3. Verify filter term counters and `then routing-instance`, ingress placement, and a matching route plus resolved next hop in the target table.
  4. Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.

Correct answer: D

Explanation of each choice

A.

The check diagnoses a different layer of service. Its source issue is: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. The relevant initial check is: Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.

B.

This check may help with another root cause, for example: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. It does not test the first failed condition; start with: Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.

C.

That evidence could be normal while the reported defect persists. It is aimed at: A provider's firewall filter counts customer steering matches yet tagged traffic goes to the ordinary next hop because the `then routing-instance` forwarding path was not verified. Instead inspect: Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution.

D.

Inspect the RIB group table list and attached protocols/interfaces, then verify the affected route in both RIBs and check its resolution. RIB groups redistribute route entries between tables, whereas a BGP community labels routes but does not itself copy an interface route to another RIB.

Question 61

A production change request at Redleaf Airports includes this finding: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. What should the engineer change to address it?

  1. Build a narrowly matched firewall filter that selects the intended forwarding routing instance and verify the target instance has the necessary route and next-hop resolution.
  2. Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.
  3. Update or remove the stale static route and validate the intended reachable next hop and route preference before restoring forwarding.
  4. Apply the correct RIB group and route import policy at the route source to import only the intended routes into the secondary RIB.

Correct answer: B

Explanation of each choice

A.

This action may apply to a different problem, for example: A packet class identified by source address needs to use a dedicated service routing table, but packets still follow the global destination-based path. It does not repair the stated failure boundary. The case-specific reason is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

B.

Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution. The case-specific reason is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active. A direct acceptance test is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

C.

That would address a separate configuration fault: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. This stem identifies a different cause, corrected by: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

D.

This action may apply to a different problem, for example: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. It does not repair the stated failure boundary. The case-specific reason is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

Question 62

After Redleaf Airports applies its proposed fix to this problem — Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. — which observation best proves the specific failure has been resolved?

  1. The active route for the exact prefix uses the intended source with the expected lower Junos preference and corresponding forwarding next hop.
  2. Only packets matching the defined steering terms are looked up in the intended forwarding table; nonmatching traffic stays on the default path.
  3. The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.
  4. Each tenant prefix is present in its own instance-specific routing table and traffic exits through that tenant's correct interface without cross-customer leakage.

Correct answer: C

Explanation of each choice

A.

This would be valid for another situation: A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. It does not establish that the failing boundary in this scenario works; verify: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

B.

The observation confirms a different component's behavior. Its source context is: A provider's firewall filter counts customer steering matches yet tagged traffic goes to the ordinary next hop because the `then routing-instance` forwarding path was not verified. In this case the success criterion is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

C.

The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering. Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

D.

This would be valid for another situation: A provider migrates a service into a separate virtual routing instance but tests only inet.0 and falsely concludes that the tenant route is absent. It does not establish that the failing boundary in this scenario works; verify: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

Question 63

An architecture review at Redleaf Airports examines the following symptom: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. What Junos or protocol mechanism is most directly responsible?

  1. Filter-based forwarding applies a routing-instance lookup decision based on a firewall filter rather than relying only on the ordinary destination table.
  2. Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.
  3. Junos routing instances maintain distinct routing-table contexts so overlapping customer prefixes can be resolved without sharing the same default RIB.
  4. A Junos RIB group imports routes into a defined primary and additional routing table when attached to the correct configuration context.

Correct answer: B

Explanation of each choice

A.

That principle belongs to a different service stage: A packet class identified by source address needs to use a dedicated service routing table, but packets still follow the global destination-based path. The directly relevant mechanism is: Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

B.

Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them. The key distinction is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active. Accordingly the remedy is: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

C.

The statement can be true when Two wholesale customers use overlapping IPv4 ranges and route lookups occur in the default table, causing one tenant's prefix to shadow the other's. But it does not explain the reported failure. Here: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

D.

That principle belongs to a different service stage: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. The directly relevant mechanism is: Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

Question 64

The team at Redleaf Airports defers a fix for this condition: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. What failure is most likely if no targeted control is applied?

  1. Traffic can bypass the required service path or reach a routing instance with no usable route, creating policy bypass or a blackhole.
  2. Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.
  3. The unintended route stays active and can override a healthier dynamic path during failure recovery or maintenance.
  4. Traffic for the specific prefix continues to follow the dead or incorrect next hop instead of recovering through an available alternate path.

Correct answer: B

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: A packet class identified by source address needs to use a dedicated service routing table, but packets still follow the global destination-based path. The described fault instead exposes: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

B.

Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates. The direct mitigation is: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

C.

The concern could occur elsewhere when A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. For the stated scenario, the immediate risk is: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

D.

That consequence is more closely associated with another deficiency, such as: A service edge was renumbered and its manually configured static next hop still points to the former address, blackholing one customer subnet despite healthy dynamic adjacencies. The described fault instead exposes: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

Question 65

During provider troubleshooting at Redleaf Airports, this symptom is observed: Traffic to one equal-cost destination uses only a single next hop despite two active parallel paths and an approved traffic-sharing requirement. Which targeted inspection should precede remediation?

  1. Inspect the protective route's next-hop type and run tests for both a known more-specific destination and an unmatched address in the summary.
  2. Identify the ingress logical interface's routing-instance membership and inspect the corresponding instance RIB and forwarding table, not just inet.0.
  3. Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.
  4. Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.

Correct answer: C

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: A provider intends a protective summary for address space with sparse more-specific destinations but needs unmatched traffic to be dropped predictably rather than looped. Instead inspect: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

B.

The check diagnoses a different layer of service. Its source issue is: A provider migrates a service into a separate virtual routing instance but tests only inet.0 and falsely concludes that the tenant route is absent. The relevant initial check is: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

C.

Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop. Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

D.

That evidence could be normal while the reported defect persists. It is aimed at: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. Instead inspect: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

Question 66

At Silverpeak Data Networks, a service provider router shows this failure: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. What is the best targeted configuration or operations action?

  1. Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.
  2. Apply the correct RIB group and route import policy at the route source to import only the intended routes into the secondary RIB.
  3. Configure and validate the Junos aggregate route and its contributing more-specific active routes, applying appropriate export policy for the intended summary.
  4. Select and document the intended discard versus reject next-hop behavior on the protective route, while preserving active more-specific routes for legitimate destinations.

Correct answer: A

Explanation of each choice

A.

Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution. The case-specific reason is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active. A direct acceptance test is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

B.

This action may apply to a different problem, for example: A provider expects selected interface routes from an underlay RIB to be available in a second table, but the secondary table has no copied routes. It does not repair the stated failure boundary. The case-specific reason is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

C.

The other action is relevant when A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. The current case instead requires: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution. The distinction is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

D.

That would address a separate configuration fault: A provider intends a protective summary for address space with sparse more-specific destinations but needs unmatched traffic to be dropped predictably rather than looped. This stem identifies a different cause, corrected by: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

Question 67

A change auditor at Silverpeak Data Networks must validate remediation of this finding: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. Which test outcome is the strongest acceptance evidence?

  1. The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.
  2. The configured aggregate is active only when valid contributing routes exist, and approved peers receive the summary instead of an accidental flood of individual specifics.
  3. The generated route appears while its qualifying active contributor is present and withdraws when the contributor is removed, with the next hop resolved as designed.
  4. The active route and installed forwarding entry for the affected prefix point toward the reachable intended neighbor, and test traffic succeeds over the selected path.

Correct answer: A

Explanation of each choice

A.

The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering. Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

B.

The observation confirms a different component's behavior. Its source context is: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. In this case the success criterion is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

C.

The observation confirms a different component's behavior. Its source context is: An enterprise receives a transit path that should trigger a conditional route of last resort; when that contributor disappears the default must be removed to avoid a blackhole. In this case the success criterion is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

D.

That check proves something else, such as: A maintenance circuit has been retired but an old static route still directs a private customer prefix toward its unresponsive next hop, even while a learned backup route exists. It could pass while the stated problem remains. The targeted evidence here is: The forwarding table contains the intended set of usable equal-cost next hops and sampled independent flows use multiple paths without unexpected per-packet reordering.

Question 68

The operations training team at Silverpeak Data Networks discusses this issue: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. Which technical explanation matches the intended correction?

  1. A Junos RIB group imports routes into a defined primary and additional routing table when attached to the correct configuration context.
  2. Between competing route sources for an identical destination, Junos normally prefers the route with the lower route-preference value before forwarding installation.
  3. Martian addresses are prefixes considered invalid for ordinary routing and can be rejected independently of normal policy attribute preferences.
  4. Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

Correct answer: D

Explanation of each choice

A.

The statement can be true when A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. But it does not explain the reported failure. Here: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

B.

That principle belongs to a different service stage: A static route and OSPF route cover the identical prefix; the active path is the static one even though the team expected OSPF to win. The directly relevant mechanism is: Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

C.

This explains a separate protocol behavior: A peer presents a route for an address block treated as martian by the platform; engineers mistakenly troubleshoot export communities rather than the fundamental invalid-prefix classification. In the current facts, the controlling mechanism is: Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them.

D.

Junos route selection and export to the forwarding table are distinct; ECMP forwarding requires eligible paths and policy behavior that installs them. The key distinction is: Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active. Accordingly the remedy is: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

Question 69

At Silverpeak Data Networks, a service acceptance review considers the unresolved issue: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. Which operational exposure follows most directly?

  1. The provider might leak granular routes or blackhole addresses inside an overbroad summary if contribution and export behavior are not checked.
  2. An unconditional default can remain active after backbone reachability disappears and silently send many unmatched destinations to a failed path.
  3. The secondary routing process lacks required reachability or inadvertently imports unrelated routes if the RIB group is attached too broadly.
  4. Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

Correct answer: D

Explanation of each choice

A.

That consequence is more closely associated with another deficiency, such as: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. The described fault instead exposes: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

B.

That consequence is more closely associated with another deficiency, such as: An edge should install a conditional default only while a qualifying backbone route is reachable, but an unconditional static default currently hides an upstream outage. The described fault instead exposes: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

C.

It is a risk in another topology or protocol state: A services router has a valid connected path in the primary instance yet a policy-dependent secondary RIB never receives it after a routing-instance refactor. Here the most direct failure path is: Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates.

D.

Traffic remains concentrated on one link, causing congestion and making the redundant path ineffective despite multiple RIB candidates. The direct mitigation is: Confirm equal eligible next hops and apply the appropriate forwarding-table load-balancing policy, then verify actual forwarding next-hop groups and flow distribution.

Question 70

Before changing configuration at Silverpeak Data Networks, an engineer investigates: A provider turns on ECMP routing but the forwarding table still resolves customer flows to just one path and operators mistake RIB entries for per-flow distribution. Which first diagnostic most directly tests the suspected cause?

  1. Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.
  2. Identify the ingress logical interface's routing-instance membership and inspect the corresponding instance RIB and forwarding table, not just inet.0.
  3. Inspect aggregate route state, contributing routes in the source RIB, configured preference and export policy, then compare advertised routes with intended boundaries.
  4. Check the prefix classification, `show route` reason/state and martian configuration before changing protocol preference or BGP export policy.

Correct answer: A

Explanation of each choice

A.

Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop. Equal routes in a control-plane table alone do not prove forwarding-plane hashing or path sharing is active.

B.

That evidence could be normal while the reported defect persists. It is aimed at: Two wholesale customers use overlapping IPv4 ranges and route lookups occur in the default table, causing one tenant's prefix to shadow the other's. Instead inspect: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

C.

The check diagnoses a different layer of service. Its source issue is: A provider aggregate continues to be advertised when an operator assumes that any configured aggregate is independent of contributing routes, and wants to validate how the summary activates. The relevant initial check is: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

D.

This check may help with another root cause, for example: A routing policy change appears to accept a reserved loopback or multicast source as an ordinary Internet destination, and the team needs to separate policy bugs from invalid route treatment. It does not test the first failed condition; start with: Inspect route next-hop eligibility and the forwarding-table route for that prefix, then check the load-balancing policy and counters per next hop.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports