Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 34

Question 330

A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. The proposed correction is: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols. Which observation MOST directly confirms this fault is resolved?

  1. Customer BPDUs reach the remote customer end, and provider STP remains isolated from them.
  2. The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.
  3. The bridges report the same MST region and the expected per-instance root information.
  4. Customer control PDUs are carried only along authorized service paths in verification captures.

Explanation

Correct Answer

D:

Customer control PDUs are carried only along authorized service paths in verification captures. This is the direct acceptance evidence for the observed failure: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. The mechanism being validated is: L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.

Incorrect Answers

A:

Customer BPDUs reach the remote customer end, and provider STP remains isolated from them. That would validate a different condition: Two customer sites must exchange spanning-tree BPDUs over a provider Ethernet service without letting those BPDUs alter the provider's own STP topology. The decisive check for the current issue is: Customer control PDUs are carried only along authorized service paths in verification captures.

B:

The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers. That would validate a different condition: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The decisive check for the current issue is: Customer control PDUs are carried only along authorized service paths in verification captures.

C:

The bridges report the same MST region and the expected per-instance root information. That would validate a different condition: A large switch estate uses MSTP with different VLAN-to-instance maps on neighbors that should form one region. The decisive check for the current issue is: Customer control PDUs are carried only along authorized service paths in verification captures.

Question 331

A Junos engineer proposes this response: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols. The situation is: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. Which technical principle BEST justifies the response?

  1. L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.
  2. L2PT carries selected customer Layer 2 control packets transparently across a transport domain.
  3. Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.
  4. MSTP region agreement depends on configuration identifier components including the VLAN mapping.

Explanation

Correct Answer

A:

L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic. This is the controlling mechanism in the specific case: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. It predicts the acceptance result: Customer control PDUs are carried only along authorized service paths in verification captures.

Incorrect Answers

B:

L2PT carries selected customer Layer 2 control packets transparently across a transport domain. This principle explains a separate situation: Two customer sites must exchange spanning-tree BPDUs over a provider Ethernet service without letting those BPDUs alter the provider's own STP topology. For this issue the relevant mechanism is: L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.

C:

Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts. This principle explains a separate situation: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. For this issue the relevant mechanism is: L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.

D:

MSTP region agreement depends on configuration identifier components including the VLAN mapping. This principle explains a separate situation: A large switch estate uses MSTP with different VLAN-to-instance maps on neighbors that should form one region. For this issue the relevant mechanism is: L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.

Question 332

A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. If the team bypasses or fails to implement the targeted correction (Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols.), which direct operational risk or residual exposure is MOST relevant?

  1. Processing customer BPDUs as local provider control traffic can affect the provider spanning tree.
  2. Too-broad tunneling can spread unwanted customer control messages beyond the service boundary.
  3. Mapping only one C-VLAN leaves other required tenant frames untransported.
  4. Mismatched MST region configuration can create an unintended boundary and forwarding topology.

Explanation

Correct Answer

B:

Too-broad tunneling can spread unwanted customer control messages beyond the service boundary. This is the consequence linked to the observed situation: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. It is prevented by: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols. The underlying reason is: L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.

Incorrect Answers

A:

Processing customer BPDUs as local provider control traffic can affect the provider spanning tree. This risk belongs to a different operational problem: Two customer sites must exchange spanning-tree BPDUs over a provider Ethernet service without letting those BPDUs alter the provider's own STP topology. The stated condition instead exposes this direct risk: Too-broad tunneling can spread unwanted customer control messages beyond the service boundary. The appropriate mitigation is: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols.

C:

Mapping only one C-VLAN leaves other required tenant frames untransported. This risk belongs to a different operational problem: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The stated condition instead exposes this direct risk: Too-broad tunneling can spread unwanted customer control messages beyond the service boundary. The appropriate mitigation is: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols.

D:

Mismatched MST region configuration can create an unintended boundary and forwarding topology. This risk belongs to a different operational problem: A large switch estate uses MSTP with different VLAN-to-instance maps on neighbors that should form one region. The stated condition instead exposes this direct risk: Too-broad tunneling can spread unwanted customer control messages beyond the service boundary. The appropriate mitigation is: Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols.

Question 333

A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Inspect MVRP leave and deregistration state and remove the stale participating registration.
  2. Put the intended VLAN and MVRP participation on the supported trunk interfaces.
  3. Apply the supported spanning-tree edge-port role only on the true endpoint-facing access port.
  4. Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

Explanation

Correct Answer

D:

Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support. This change specifically addresses the reported evidence: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The relevant protocol mechanism is: MVRP dynamically registers active VLAN memberships on supported trunk links. A decisive acceptance test would be: The new VLAN is advertised and installed on participating transport trunks without manual additions.

Incorrect Answers

A:

Inspect MVRP leave and deregistration state and remove the stale participating registration. This is a valid solution to a different Junos situation: During MVRP migration, a retired VLAN continues appearing on downstream trunks after its last authorized user is disconnected. It does not directly correct the specific failure evidence here: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The required targeted change is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

B:

Put the intended VLAN and MVRP participation on the supported trunk interfaces. This is a valid solution to a different Junos situation: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. It does not directly correct the specific failure evidence here: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The required targeted change is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

C:

Apply the supported spanning-tree edge-port role only on the true endpoint-facing access port. This is a valid solution to a different Junos situation: An edge desk port is treated as a transit switch link and waits for STP convergence every time a workstation reconnects. It does not directly correct the specific failure evidence here: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The required targeted change is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

Question 334

A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The proposed correction is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support. Which observation MOST directly confirms this fault is resolved?

  1. The new VLAN is advertised and installed on participating transport trunks without manual additions.
  2. The VLAN membership is pruned after valid leave-state convergence on relevant trunks.
  3. The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.
  4. The workstation port enters forwarding promptly without creating transit-device bridging loops.

Explanation

Correct Answer

A:

The new VLAN is advertised and installed on participating transport trunks without manual additions. This is the direct acceptance evidence for the observed failure: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The mechanism being validated is: MVRP dynamically registers active VLAN memberships on supported trunk links.

Incorrect Answers

B:

The VLAN membership is pruned after valid leave-state convergence on relevant trunks. That would validate a different condition: During MVRP migration, a retired VLAN continues appearing on downstream trunks after its last authorized user is disconnected. The decisive check for the current issue is: The new VLAN is advertised and installed on participating transport trunks without manual additions.

C:

The VLAN registration appears across the neighboring trunk while access-port delivery remains correct. That would validate a different condition: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The decisive check for the current issue is: The new VLAN is advertised and installed on participating transport trunks without manual additions.

D:

The workstation port enters forwarding promptly without creating transit-device bridging loops. That would validate a different condition: An edge desk port is treated as a transit switch link and waits for STP convergence every time a workstation reconnects. The decisive check for the current issue is: The new VLAN is advertised and installed on participating transport trunks without manual additions.

Question 335

A Junos engineer proposes this response: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support. The situation is: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. Which technical principle BEST justifies the response?

  1. MVRP registration modes and boundary configuration constrain advertised VLAN membership.
  2. MVRP dynamically registers active VLAN memberships on supported trunk links.
  3. An Ethernet trunk forwards only VLAN memberships configured or registered as eligible.
  4. VSTP maintains a separate spanning-tree instance for each VLAN.

Explanation

Correct Answer

B:

MVRP dynamically registers active VLAN memberships on supported trunk links. This is the controlling mechanism in the specific case: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. It predicts the acceptance result: The new VLAN is advertised and installed on participating transport trunks without manual additions.

Incorrect Answers

A:

MVRP registration modes and boundary configuration constrain advertised VLAN membership. This principle explains a separate situation: A guest VLAN should never propagate into an upstream trunk that participates in MVRP with multiple tenant switches. For this issue the relevant mechanism is: MVRP dynamically registers active VLAN memberships on supported trunk links.

C:

An Ethernet trunk forwards only VLAN memberships configured or registered as eligible. This principle explains a separate situation: A VLAN should cross an EX access-to-distribution trunk but remains absent from forwarding because it was not allowed on the uplink. For this issue the relevant mechanism is: MVRP dynamically registers active VLAN memberships on supported trunk links.

D:

VSTP maintains a separate spanning-tree instance for each VLAN. This principle explains a separate situation: A network interconnects switches that require one separate spanning-tree instance for each VLAN instead of the grouped MSTP model. For this issue the relevant mechanism is: MVRP dynamically registers active VLAN memberships on supported trunk links.

Question 336

A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. If the team bypasses or fails to implement the targeted correction (Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.), which direct operational risk or residual exposure is MOST relevant?

  1. Failure to prune expired VLANs can unnecessarily extend broadcast domains and BUM traffic.
  2. Enabling MVRP on access-only ports does not provide the intended trunk registration process.
  3. Assuming a VLAN can traverse every trunk without registration can strand newly created segments.
  4. Marking actual switch-to-switch links as edge can weaken topology change safeguards.

Explanation

Correct Answer

C:

Assuming a VLAN can traverse every trunk without registration can strand newly created segments. This is the consequence linked to the observed situation: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. It is prevented by: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support. The underlying reason is: MVRP dynamically registers active VLAN memberships on supported trunk links.

Incorrect Answers

A:

Failure to prune expired VLANs can unnecessarily extend broadcast domains and BUM traffic. This risk belongs to a different operational problem: During MVRP migration, a retired VLAN continues appearing on downstream trunks after its last authorized user is disconnected. The stated condition instead exposes this direct risk: Assuming a VLAN can traverse every trunk without registration can strand newly created segments. The appropriate mitigation is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

B:

Enabling MVRP on access-only ports does not provide the intended trunk registration process. This risk belongs to a different operational problem: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The stated condition instead exposes this direct risk: Assuming a VLAN can traverse every trunk without registration can strand newly created segments. The appropriate mitigation is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

D:

Marking actual switch-to-switch links as edge can weaken topology change safeguards. This risk belongs to a different operational problem: An edge desk port is treated as a transit switch link and waits for STP convergence every time a workstation reconnects. The stated condition instead exposes this direct risk: Assuming a VLAN can traverse every trunk without registration can strand newly created segments. The appropriate mitigation is: Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.

Question 337

MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Put the intended VLAN and MVRP participation on the supported trunk interfaces.
  2. Authorize the needed VLAN on the correct supported trunk without opening unrelated VLANs.
  3. Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support.
  4. Apply the intended ingress filter-based VLAN policy at the supported classification boundary.

Explanation

Correct Answer

A:

Put the intended VLAN and MVRP participation on the supported trunk interfaces. This change specifically addresses the reported evidence: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The relevant protocol mechanism is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports. A decisive acceptance test would be: The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.

Incorrect Answers

B:

Authorize the needed VLAN on the correct supported trunk without opening unrelated VLANs. This is a valid solution to a different Junos situation: A VLAN should cross an EX access-to-distribution trunk but remains absent from forwarding because it was not allowed on the uplink. It does not directly correct the specific failure evidence here: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The required targeted change is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

C:

Enable supported MVRP dynamic VLAN registration on the participating trunks after verifying platform support. This is a valid solution to a different Junos situation: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. It does not directly correct the specific failure evidence here: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The required targeted change is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

D:

Apply the intended ingress filter-based VLAN policy at the supported classification boundary. This is a valid solution to a different Junos situation: A filter-based VLAN reassignment takes effect on the uplink instead of the ingress edge and breaks already classified traffic. It does not directly correct the specific failure evidence here: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The required targeted change is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

Question 338

MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The proposed correction is: Put the intended VLAN and MVRP participation on the supported trunk interfaces. Which observation MOST directly confirms this fault is resolved?

  1. The trunk carries tagged frames for that VLAN and local MAC learning resumes.
  2. The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.
  3. The new VLAN is advertised and installed on participating transport trunks without manual additions.
  4. Packet tracing confirms VLAN assignment at ingress and no unintended reclassification on transit ports.

Explanation

Correct Answer

B:

The VLAN registration appears across the neighboring trunk while access-port delivery remains correct. This is the direct acceptance evidence for the observed failure: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. The mechanism being validated is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.

Incorrect Answers

A:

The trunk carries tagged frames for that VLAN and local MAC learning resumes. That would validate a different condition: A VLAN should cross an EX access-to-distribution trunk but remains absent from forwarding because it was not allowed on the uplink. The decisive check for the current issue is: The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.

C:

The new VLAN is advertised and installed on participating transport trunks without manual additions. That would validate a different condition: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The decisive check for the current issue is: The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.

D:

Packet tracing confirms VLAN assignment at ingress and no unintended reclassification on transit ports. That would validate a different condition: A filter-based VLAN reassignment takes effect on the uplink instead of the ingress edge and breaks already classified traffic. The decisive check for the current issue is: The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.

Question 339

A Junos engineer proposes this response: Put the intended VLAN and MVRP participation on the supported trunk interfaces. The situation is: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. Which technical principle BEST justifies the response?

  1. An Ethernet trunk forwards only VLAN memberships configured or registered as eligible.
  2. MVRP dynamically registers active VLAN memberships on supported trunk links.
  3. MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.
  4. Filter-based VLAN classification is sensitive to the point in the Layer 2 forwarding pipeline.

Explanation

Correct Answer

C:

MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports. This is the controlling mechanism in the specific case: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. It predicts the acceptance result: The VLAN registration appears across the neighboring trunk while access-port delivery remains correct.

Incorrect Answers

A:

An Ethernet trunk forwards only VLAN memberships configured or registered as eligible. This principle explains a separate situation: A VLAN should cross an EX access-to-distribution trunk but remains absent from forwarding because it was not allowed on the uplink. For this issue the relevant mechanism is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.

B:

MVRP dynamically registers active VLAN memberships on supported trunk links. This principle explains a separate situation: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. For this issue the relevant mechanism is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.

D:

Filter-based VLAN classification is sensitive to the point in the Layer 2 forwarding pipeline. This principle explains a separate situation: A filter-based VLAN reassignment takes effect on the uplink instead of the ingress edge and breaks already classified traffic. For this issue the relevant mechanism is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.

Question 340

MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. If the team bypasses or fails to implement the targeted correction (Put the intended VLAN and MVRP participation on the supported trunk interfaces.), which direct operational risk or residual exposure is MOST relevant?

  1. Opening every VLAN to fix one missing membership expands an unnecessary Layer 2 failure domain.
  2. Assuming a VLAN can traverse every trunk without registration can strand newly created segments.
  3. Applying classification too late can change already separated tenant traffic.
  4. Enabling MVRP on access-only ports does not provide the intended trunk registration process.

Explanation

Correct Answer

D:

Enabling MVRP on access-only ports does not provide the intended trunk registration process. This is the consequence linked to the observed situation: MVRP is enabled between two switches but a new VLAN is advertised only on an access port that is not a trunk member. It is prevented by: Put the intended VLAN and MVRP participation on the supported trunk interfaces. The underlying reason is: MVRP exchanges VLAN registration information on trunk links rather than arbitrary access ports.

Incorrect Answers

A:

Opening every VLAN to fix one missing membership expands an unnecessary Layer 2 failure domain. This risk belongs to a different operational problem: A VLAN should cross an EX access-to-distribution trunk but remains absent from forwarding because it was not allowed on the uplink. The stated condition instead exposes this direct risk: Enabling MVRP on access-only ports does not provide the intended trunk registration process. The appropriate mitigation is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

B:

Assuming a VLAN can traverse every trunk without registration can strand newly created segments. This risk belongs to a different operational problem: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The stated condition instead exposes this direct risk: Enabling MVRP on access-only ports does not provide the intended trunk registration process. The appropriate mitigation is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

C:

Applying classification too late can change already separated tenant traffic. This risk belongs to a different operational problem: A filter-based VLAN reassignment takes effect on the uplink instead of the ingress edge and breaks already classified traffic. The stated condition instead exposes this direct risk: Enabling MVRP on access-only ports does not provide the intended trunk registration process. The appropriate mitigation is: Put the intended VLAN and MVRP participation on the supported trunk interfaces.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports