Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 32

Question 310

A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The proposed correction is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. Which observation MOST directly confirms this fault is resolved?

  1. Clients can reach the gateway but isolated peer-to-peer Layer 2 frames are blocked.
  2. The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.
  3. Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
  4. The new VLAN is advertised and installed on participating transport trunks without manual additions.

Explanation

Correct Answer

C:

Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100. This is the direct acceptance evidence for the observed failure: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The mechanism being validated is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

Incorrect Answers

A:

Clients can reach the gateway but isolated peer-to-peer Layer 2 frames are blocked. That would validate a different condition: A hosting switch allows isolated customers to access a gateway but the customers must not talk directly to one another inside the same service subnet. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.

B:

The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag. That would validate a different condition: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.

D:

The new VLAN is advertised and installed on participating transport trunks without manual additions. That would validate a different condition: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.

Question 311

A Junos engineer proposes this response: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. The situation is: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. Which technical principle BEST justifies the response?

  1. Private VLANs constrain Layer 2 communication among secondary ports while allowing gateway access.
  2. L2PT must include each selected protocol's PDUs for transparent customer control transport.
  3. Independent VSTP instances can use distinct roots and forwarding trees per VLAN.
  4. IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

Explanation

Correct Answer

D:

IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag. This is the controlling mechanism in the specific case: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. It predicts the acceptance result: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.

Incorrect Answers

A:

Private VLANs constrain Layer 2 communication among secondary ports while allowing gateway access. This principle explains a separate situation: A hosting switch allows isolated customers to access a gateway but the customers must not talk directly to one another inside the same service subnet. For this issue the relevant mechanism is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

B:

L2PT must include each selected protocol's PDUs for transparent customer control transport. This principle explains a separate situation: A service provider already transports customer data VLANs but the remote customer's LLDP frames never reach its opposite endpoint. For this issue the relevant mechanism is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

C:

Independent VSTP instances can use distinct roots and forwarding trees per VLAN. This principle explains a separate situation: Two redundant campus uplinks participate in VSTP but the traffic for a specific VLAN takes the uplink intentionally reserved for another segment. For this issue the relevant mechanism is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

Question 312

A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. If the team bypasses or fails to implement the targeted correction (Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.), which direct operational risk or residual exposure is MOST relevant?

  1. Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID.
  2. Using an ordinary shared access VLAN would permit unwanted host-to-host communication.
  3. Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames.
  4. Assuming a VLAN can traverse every trunk without registration can strand newly created segments.

Explanation

Correct Answer

A:

Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. This is the consequence linked to the observed situation: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. It is prevented by: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. The underlying reason is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.

Incorrect Answers

B:

Using an ordinary shared access VLAN would permit unwanted host-to-host communication. This risk belongs to a different operational problem: A hosting switch allows isolated customers to access a gateway but the customers must not talk directly to one another inside the same service subnet. The stated condition instead exposes this direct risk: Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. The appropriate mitigation is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.

C:

Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. This risk belongs to a different operational problem: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The stated condition instead exposes this direct risk: Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. The appropriate mitigation is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.

D:

Assuming a VLAN can traverse every trunk without registration can strand newly created segments. This risk belongs to a different operational problem: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The stated condition instead exposes this direct risk: Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. The appropriate mitigation is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.

Question 313

A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.
  2. Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.
  3. Verify the intended service VLAN pop operation on the downstream provider egress port.
  4. Assign the intended hosts to the same private VLAN community and separate other communities.

Explanation

Correct Answer

C:

Verify the intended service VLAN pop operation on the downstream provider egress port. This change specifically addresses the reported evidence: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The relevant protocol mechanism is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff. A decisive acceptance test would be: The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

Incorrect Answers

A:

Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. This is a valid solution to a different Junos situation: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. It does not directly correct the specific failure evidence here: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The required targeted change is: Verify the intended service VLAN pop operation on the downstream provider egress port.

B:

Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces. This is a valid solution to a different Junos situation: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. It does not directly correct the specific failure evidence here: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The required targeted change is: Verify the intended service VLAN pop operation on the downstream provider egress port.

D:

Assign the intended hosts to the same private VLAN community and separate other communities. This is a valid solution to a different Junos situation: Two hosts in a private VLAN community must communicate with each other, while remaining isolated from hosts in a different community. It does not directly correct the specific failure evidence here: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The required targeted change is: Verify the intended service VLAN pop operation on the downstream provider egress port.

Question 314

A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The proposed correction is: Verify the intended service VLAN pop operation on the downstream provider egress port. Which observation MOST directly confirms this fault is resolved?

  1. Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
  2. The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.
  3. A Layer 2 test passes within the authorized community and fails across segregated communities.
  4. The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

Explanation

Correct Answer

D:

The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag. This is the direct acceptance evidence for the observed failure: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The mechanism being validated is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.

Incorrect Answers

A:

Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100. That would validate a different condition: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The decisive check for the current issue is: The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

B:

The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers. That would validate a different condition: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The decisive check for the current issue is: The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

C:

A Layer 2 test passes within the authorized community and fails across segregated communities. That would validate a different condition: Two hosts in a private VLAN community must communicate with each other, while remaining isolated from hosts in a different community. The decisive check for the current issue is: The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

Question 315

A Junos engineer proposes this response: Verify the intended service VLAN pop operation on the downstream provider egress port. The situation is: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. Which technical principle BEST justifies the response?

  1. A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.
  2. Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.
  3. L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic.
  4. MSTP region agreement depends on configuration identifier components including the VLAN mapping.

Explanation

Correct Answer

A:

A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff. This is the controlling mechanism in the specific case: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. It predicts the acceptance result: The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.

Incorrect Answers

B:

Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts. This principle explains a separate situation: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. For this issue the relevant mechanism is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.

C:

L2PT scope defines which interfaces and protocol messages are handled as tunneled control traffic. This principle explains a separate situation: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. For this issue the relevant mechanism is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.

D:

MSTP region agreement depends on configuration identifier components including the VLAN mapping. This principle explains a separate situation: A large switch estate uses MSTP with different VLAN-to-instance maps on neighbors that should form one region. For this issue the relevant mechanism is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.

Question 316

A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. If the team bypasses or fails to implement the targeted correction (Verify the intended service VLAN pop operation on the downstream provider egress port.), which direct operational risk or residual exposure is MOST relevant?

  1. Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID.
  2. Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames.
  3. Mapping only one C-VLAN leaves other required tenant frames untransported.
  4. Putting all tenants in one community can defeat the intended intra-customer isolation.

Explanation

Correct Answer

B:

Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. This is the consequence linked to the observed situation: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. It is prevented by: Verify the intended service VLAN pop operation on the downstream provider egress port. The underlying reason is: A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.

Incorrect Answers

A:

Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. This risk belongs to a different operational problem: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The stated condition instead exposes this direct risk: Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. The appropriate mitigation is: Verify the intended service VLAN pop operation on the downstream provider egress port.

C:

Mapping only one C-VLAN leaves other required tenant frames untransported. This risk belongs to a different operational problem: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The stated condition instead exposes this direct risk: Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. The appropriate mitigation is: Verify the intended service VLAN pop operation on the downstream provider egress port.

D:

Putting all tenants in one community can defeat the intended intra-customer isolation. This risk belongs to a different operational problem: Two hosts in a private VLAN community must communicate with each other, while remaining isolated from hosts in a different community. The stated condition instead exposes this direct risk: Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. The appropriate mitigation is: Verify the intended service VLAN pop operation on the downstream provider egress port.

Question 317

A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols.
  2. Add the supported LLDP control protocol to the relevant L2PT tunnel treatment.
  3. Match the MSTP region name, revision and VLAN-to-instance digest on all intended region members.
  4. Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

Explanation

Correct Answer

D:

Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces. This change specifically addresses the reported evidence: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The relevant protocol mechanism is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts. A decisive acceptance test would be: The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.

Incorrect Answers

A:

Limit Layer 2 protocol tunneling to the intended service UNI interfaces and recognized control protocols. This is a valid solution to a different Junos situation: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. It does not directly correct the specific failure evidence here: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The required targeted change is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

B:

Add the supported LLDP control protocol to the relevant L2PT tunnel treatment. This is a valid solution to a different Junos situation: A service provider already transports customer data VLANs but the remote customer's LLDP frames never reach its opposite endpoint. It does not directly correct the specific failure evidence here: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The required targeted change is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

C:

Match the MSTP region name, revision and VLAN-to-instance digest on all intended region members. This is a valid solution to a different Junos situation: A large switch estate uses MSTP with different VLAN-to-instance maps on neighbors that should form one region. It does not directly correct the specific failure evidence here: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The required targeted change is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

Question 318

A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The proposed correction is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces. Which observation MOST directly confirms this fault is resolved?

  1. The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.
  2. Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
  3. The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag.
  4. Customer control PDUs are carried only along authorized service paths in verification captures.

Explanation

Correct Answer

A:

The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers. This is the direct acceptance evidence for the observed failure: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. The mechanism being validated is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.

Incorrect Answers

B:

Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100. That would validate a different condition: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The decisive check for the current issue is: The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.

C:

The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag. That would validate a different condition: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The decisive check for the current issue is: The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.

D:

Customer control PDUs are carried only along authorized service paths in verification captures. That would validate a different condition: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. The decisive check for the current issue is: The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.

Question 319

A Junos engineer proposes this response: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces. The situation is: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. Which technical principle BEST justifies the response?

  1. IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.
  2. Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.
  3. A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff.
  4. Private VLAN community ports permit same-community exchange but limit other secondary traffic.

Explanation

Correct Answer

B:

Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts. This is the controlling mechanism in the specific case: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. It predicts the acceptance result: The intended C-VLANs traverse with the shared outer S-VLAN while retaining their inner identifiers.

Incorrect Answers

A:

IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag. This principle explains a separate situation: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. For this issue the relevant mechanism is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.

C:

A Q-in-Q service adds an outer tag for transit and removes that provider tag at customer handoff. This principle explains a separate situation: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. For this issue the relevant mechanism is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.

D:

Private VLAN community ports permit same-community exchange but limit other secondary traffic. This principle explains a separate situation: Two hosts in a private VLAN community must communicate with each other, while remaining isolated from hosts in a different community. For this issue the relevant mechanism is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.

Question 320

A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. If the team bypasses or fails to implement the targeted correction (Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.), which direct operational risk or residual exposure is MOST relevant?

  1. Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID.
  2. Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames.
  3. Mapping only one C-VLAN leaves other required tenant frames untransported.
  4. Too-broad tunneling can spread unwanted customer control messages beyond the service boundary.

Explanation

Correct Answer

C:

Mapping only one C-VLAN leaves other required tenant frames untransported. This is the consequence linked to the observed situation: A provider wants to map several different customer C-VLANs from one site into one transport S-VLAN over a shared uplink. It is prevented by: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces. The underlying reason is: Q-in-Q maps customer VLAN identifiers into service VLAN transport contexts.

Incorrect Answers

A:

Forwarding on the inner VLAN alone can merge unrelated customers who reuse the same C-VLAN ID. This risk belongs to a different operational problem: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The stated condition instead exposes this direct risk: Mapping only one C-VLAN leaves other required tenant frames untransported. The appropriate mitigation is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

B:

Failing to remove the service tag can prevent the customer switch accepting expected VLAN frames. This risk belongs to a different operational problem: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The stated condition instead exposes this direct risk: Mapping only one C-VLAN leaves other required tenant frames untransported. The appropriate mitigation is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

D:

Too-broad tunneling can spread unwanted customer control messages beyond the service boundary. This risk belongs to a different operational problem: A remote site reports customer protocol frames being delivered to provider-facing devices after L2PT was broadened to all interfaces. The stated condition instead exposes this direct risk: Mapping only one C-VLAN leaves other required tenant frames untransported. The appropriate mitigation is: Use an allowed many-to-one Q-in-Q customer-to-service VLAN mapping for the supported interfaces.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports