Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 8

Question 70

An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The proposed correction is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. Which observation MOST directly confirms this fault is resolved?

  1. Captured OSPF Hellos and database exchange return and the neighbor reaches Full.
  2. Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.
  3. Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
  4. The elected DR and BDR are the intended routers following an actual election event.

Explanation

Correct Answer

C:

Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic. This is the direct acceptance evidence for the observed failure: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The mechanism being validated is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

Incorrect Answers

A:

Captured OSPF Hellos and database exchange return and the neighbor reaches Full. That would validate a different condition: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.

B:

Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements. That would validate a different condition: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.

D:

The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.

Question 71

A Junos engineer proposes this response: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. The situation is: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. Which technical principle BEST justifies the response?

  1. OSPF uses its own IP protocol for routing messages rather than TCP port sessions.
  2. The OSPF stub capability must agree among routers in the same area.
  3. OSPF DR election on a broadcast segment considers configured router interface priorities.
  4. OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

Explanation

Correct Answer

D:

OSPF Dead intervals detect loss of expected Hellos independently of the physical link state. This is the controlling mechanism in the specific case: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. It predicts the acceptance result: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.

Incorrect Answers

A:

OSPF uses its own IP protocol for routing messages rather than TCP port sessions. This principle explains a separate situation: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. For this issue the relevant mechanism is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

B:

The OSPF stub capability must agree among routers in the same area. This principle explains a separate situation: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. For this issue the relevant mechanism is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

C:

OSPF DR election on a broadcast segment considers configured router interface priorities. This principle explains a separate situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. For this issue the relevant mechanism is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

Question 72

An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. If the team bypasses or fails to implement the targeted correction (Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.), which direct operational risk or residual exposure is MOST relevant?

  1. Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability.
  2. A firewall that allows only TCP and ICMP can block OSPF while giving misleading reachability tests.
  3. A mismatched area capability or external LSA leakage prevents intended stub operation.
  4. Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged.

Explanation

Correct Answer

A:

Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability. This is the consequence linked to the observed situation: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. It is prevented by: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. The underlying reason is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.

Incorrect Answers

B:

A firewall that allows only TCP and ICMP can block OSPF while giving misleading reachability tests. This risk belongs to a different operational problem: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The stated condition instead exposes this direct risk: Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability. The appropriate mitigation is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.

C:

A mismatched area capability or external LSA leakage prevents intended stub operation. This risk belongs to a different operational problem: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The stated condition instead exposes this direct risk: Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability. The appropriate mitigation is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.

D:

Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This risk belongs to a different operational problem: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The stated condition instead exposes this direct risk: Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability. The appropriate mitigation is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.

Question 73

An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.
  2. Constrain the ASBR's export policy to defined route families and inspect the changed LSA database.
  3. Configure conditional default-route origination with a policy that matches actual upstream availability.
  4. Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

Explanation

Correct Answer

C:

Configure conditional default-route origination with a policy that matches actual upstream availability. This change specifically addresses the reported evidence: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The relevant protocol mechanism is: OSPF external default advertisement is controlled by explicit origination and policy behavior. A decisive acceptance test would be: The default LSA appears only while a qualifying upstream default route remains usable.

Incorrect Answers

A:

Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. This is a valid solution to a different Junos situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. It does not directly correct the specific failure evidence here: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The required targeted change is: Configure conditional default-route origination with a policy that matches actual upstream availability.

B:

Constrain the ASBR's export policy to defined route families and inspect the changed LSA database. This is a valid solution to a different Junos situation: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. It does not directly correct the specific failure evidence here: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The required targeted change is: Configure conditional default-route origination with a policy that matches actual upstream availability.

D:

Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This is a valid solution to a different Junos situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It does not directly correct the specific failure evidence here: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The required targeted change is: Configure conditional default-route origination with a policy that matches actual upstream availability.

Question 74

An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The proposed correction is: Configure conditional default-route origination with a policy that matches actual upstream availability. Which observation MOST directly confirms this fault is resolved?

  1. Only the allowlisted external prefixes appear in downstream external LSAs.
  2. The area LSDB includes only approved external advertisements after flooding settles.
  3. The elected DR and BDR are the intended routers following an actual election event.
  4. The default LSA appears only while a qualifying upstream default route remains usable.

Explanation

Correct Answer

D:

The default LSA appears only while a qualifying upstream default route remains usable. This is the direct acceptance evidence for the observed failure: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. The mechanism being validated is: OSPF external default advertisement is controlled by explicit origination and policy behavior.

Incorrect Answers

A:

Only the allowlisted external prefixes appear in downstream external LSAs. That would validate a different condition: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The decisive check for the current issue is: The default LSA appears only while a qualifying upstream default route remains usable.

B:

The area LSDB includes only approved external advertisements after flooding settles. That would validate a different condition: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. The decisive check for the current issue is: The default LSA appears only while a qualifying upstream default route remains usable.

C:

The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: The default LSA appears only while a qualifying upstream default route remains usable.

Question 75

A Junos engineer proposes this response: Configure conditional default-route origination with a policy that matches actual upstream availability. The situation is: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. Which technical principle BEST justifies the response?

  1. OSPF external default advertisement is controlled by explicit origination and policy behavior.
  2. OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.
  3. Type-5 external LSAs distribute AS-external reachability across eligible OSPF areas.
  4. OSPF DR election on a broadcast segment considers configured router interface priorities.

Explanation

Correct Answer

A:

OSPF external default advertisement is controlled by explicit origination and policy behavior. This is the controlling mechanism in the specific case: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. It predicts the acceptance result: The default LSA appears only while a qualifying upstream default route remains usable.

Incorrect Answers

B:

OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. This principle explains a separate situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. For this issue the relevant mechanism is: OSPF external default advertisement is controlled by explicit origination and policy behavior.

C:

Type-5 external LSAs distribute AS-external reachability across eligible OSPF areas. This principle explains a separate situation: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. For this issue the relevant mechanism is: OSPF external default advertisement is controlled by explicit origination and policy behavior.

D:

OSPF DR election on a broadcast segment considers configured router interface priorities. This principle explains a separate situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. For this issue the relevant mechanism is: OSPF external default advertisement is controlled by explicit origination and policy behavior.

Question 76

An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. If the team bypasses or fails to implement the targeted correction (Configure conditional default-route origination with a policy that matches actual upstream availability.), which direct operational risk or residual exposure is MOST relevant?

  1. Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area.
  2. Always injecting a default without an exit may blackhole branch traffic during ISP failure.
  3. Failing to filter redistributed routes expands LSDB size and may expose undesired routes.
  4. Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged.

Explanation

Correct Answer

B:

Always injecting a default without an exit may blackhole branch traffic during ISP failure. This is the consequence linked to the observed situation: An OSPF edge leaks a default route but branch routers still lack their expected exit because the default is not originated under the intended policy. It is prevented by: Configure conditional default-route origination with a policy that matches actual upstream availability. The underlying reason is: OSPF external default advertisement is controlled by explicit origination and policy behavior.

Incorrect Answers

A:

Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. This risk belongs to a different operational problem: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The stated condition instead exposes this direct risk: Always injecting a default without an exit may blackhole branch traffic during ISP failure. The appropriate mitigation is: Configure conditional default-route origination with a policy that matches actual upstream availability.

C:

Failing to filter redistributed routes expands LSDB size and may expose undesired routes. This risk belongs to a different operational problem: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. The stated condition instead exposes this direct risk: Always injecting a default without an exit may blackhole branch traffic during ISP failure. The appropriate mitigation is: Configure conditional default-route origination with a policy that matches actual upstream availability.

D:

Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This risk belongs to a different operational problem: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The stated condition instead exposes this direct risk: Always injecting a default without an exit may blackhole branch traffic during ISP failure. The appropriate mitigation is: Configure conditional default-route origination with a policy that matches actual upstream availability.

Question 77

Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.
  2. Compare OSPF database records and neighbor synchronization states on both ABRs.
  3. Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output.
  4. Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

Explanation

Correct Answer

D:

Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. This change specifically addresses the reported evidence: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The relevant protocol mechanism is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone. A decisive acceptance test would be: The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.

Incorrect Answers

A:

Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This is a valid solution to a different Junos situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It does not directly correct the specific failure evidence here: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The required targeted change is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

B:

Compare OSPF database records and neighbor synchronization states on both ABRs. This is a valid solution to a different Junos situation: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. It does not directly correct the specific failure evidence here: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The required targeted change is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

C:

Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output. This is a valid solution to a different Junos situation: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. It does not directly correct the specific failure evidence here: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The required targeted change is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

Question 78

Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The proposed correction is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. Which observation MOST directly confirms this fault is resolved?

  1. The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.
  2. The elected DR and BDR are the intended routers following an actual election event.
  3. Database summaries reconcile and neighbor state reports Full after successful exchange.
  4. The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface.

Explanation

Correct Answer

A:

The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability. This is the direct acceptance evidence for the observed failure: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The mechanism being validated is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

Incorrect Answers

B:

The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.

C:

Database summaries reconcile and neighbor state reports Full after successful exchange. That would validate a different condition: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. The decisive check for the current issue is: The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.

D:

The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface. That would validate a different condition: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. The decisive check for the current issue is: The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.

Question 79

A Junos engineer proposes this response: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. The situation is: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. Which technical principle BEST justifies the response?

  1. OSPF DR election on a broadcast segment considers configured router interface priorities.
  2. OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.
  3. An OSPF adjacency needs synchronized link-state databases in addition to basic reachability.
  4. OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.

Explanation

Correct Answer

B:

OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone. This is the controlling mechanism in the specific case: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. It predicts the acceptance result: The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.

Incorrect Answers

A:

OSPF DR election on a broadcast segment considers configured router interface priorities. This principle explains a separate situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. For this issue the relevant mechanism is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

C:

An OSPF adjacency needs synchronized link-state databases in addition to basic reachability. This principle explains a separate situation: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. For this issue the relevant mechanism is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

D:

OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability. This principle explains a separate situation: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. For this issue the relevant mechanism is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

Question 80

Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. If the team bypasses or fails to implement the targeted correction (Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.), which direct operational risk or residual exposure is MOST relevant?

  1. Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged.
  2. Assuming ping success proves LSDB correctness can leave SPF decisions inconsistent.
  3. Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path.
  4. Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency.

Explanation

Correct Answer

C:

Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. This is the consequence linked to the observed situation: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. It is prevented by: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. The underlying reason is: OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

Incorrect Answers

A:

Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This risk belongs to a different operational problem: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The stated condition instead exposes this direct risk: Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. The appropriate mitigation is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

B:

Assuming ping success proves LSDB correctness can leave SPF decisions inconsistent. This risk belongs to a different operational problem: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. The stated condition instead exposes this direct risk: Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. The appropriate mitigation is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

D:

Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. This risk belongs to a different operational problem: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. The stated condition instead exposes this direct risk: Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. The appropriate mitigation is: Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports