JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. If the team bypasses or fails to implement the targeted correction (Remove passive operation from only the transit OSPF interface that requires peer formation.), which direct operational risk or residual exposure is MOST relevant?
Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. This is the consequence linked to the observed situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. It is prevented by: Remove passive operation from only the transit OSPF interface that requires peer formation. The underlying reason is: A passive OSPF interface advertises its network but does not establish router neighbors there.
Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. This risk belongs to a different operational problem: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The stated condition instead exposes this direct risk: Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. The appropriate mitigation is: Remove passive operation from only the transit OSPF interface that requires peer formation.
Mismatched area membership blocks successful link-state adjacency despite IP connectivity. This risk belongs to a different operational problem: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The stated condition instead exposes this direct risk: Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. The appropriate mitigation is: Remove passive operation from only the transit OSPF interface that requires peer formation.
Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. This risk belongs to a different operational problem: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. The stated condition instead exposes this direct risk: Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. The appropriate mitigation is: Remove passive operation from only the transit OSPF interface that requires peer formation.
A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. Which targeted engineering change is MOST directly justified by the observed evidence?
Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. This change specifically addresses the reported evidence: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The relevant protocol mechanism is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface. A decisive acceptance test would be: The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This is a valid solution to a different Junos situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It does not directly correct the specific failure evidence here: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The required targeted change is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
Configure a supported area-range summary at the responsible ABR and verify the covered prefixes. This is a valid solution to a different Junos situation: An enterprise intends to carry summarized inter-area OSPF reachability rather than thousands of individual branch loopback routes. It does not directly correct the specific failure evidence here: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The required targeted change is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
Assign unique stable 32-bit OSPF router IDs to the two participating devices. This is a valid solution to a different Junos situation: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. It does not directly correct the specific failure evidence here: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The required targeted change is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The proposed correction is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. Which observation MOST directly confirms this fault is resolved?
The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN. This is the direct acceptance evidence for the observed failure: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The mechanism being validated is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
Adjacent areas learn the expected aggregate while specific routes remain visible inside the originating area. That would validate a different condition: An enterprise intends to carry summarized inter-area OSPF reachability rather than thousands of individual branch loopback routes. The decisive check for the current issue is: The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous. That would validate a different condition: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The decisive check for the current issue is: The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
A Junos engineer proposes this response: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. The situation is: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. Which technical principle BEST justifies the response?
Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface. This is the controlling mechanism in the specific case: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. It predicts the acceptance result: The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
OSPF DR election on a broadcast segment considers configured router interface priorities. This principle explains a separate situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. For this issue the relevant mechanism is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
The OSPF stub capability must agree among routers in the same area. This principle explains a separate situation: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. For this issue the relevant mechanism is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. This principle explains a separate situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. For this issue the relevant mechanism is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. If the team bypasses or fails to implement the targeted correction (Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.), which direct operational risk or residual exposure is MOST relevant?
Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. This is the consequence linked to the observed situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. It is prevented by: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. The underlying reason is: Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This risk belongs to a different operational problem: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The stated condition instead exposes this direct risk: Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. The appropriate mitigation is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
Overly broad summaries can blackhole addresses if reachability coverage is not verified. This risk belongs to a different operational problem: An enterprise intends to carry summarized inter-area OSPF reachability rather than thousands of individual branch loopback routes. The stated condition instead exposes this direct risk: Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. The appropriate mitigation is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. This risk belongs to a different operational problem: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The stated condition instead exposes this direct risk: Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. The appropriate mitigation is: Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. Which targeted engineering change is MOST directly justified by the observed evidence?
Align the intended OSPF network type and related election behavior on the two participating interfaces. This change specifically addresses the reported evidence: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The relevant protocol mechanism is: OSPF network type determines neighbor and DR election behavior and must match the link design. A decisive acceptance test would be: The neighbor database reaches Full with the expected point-to-point or broadcast behavior.
Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. This is a valid solution to a different Junos situation: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. It does not directly correct the specific failure evidence here: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The required targeted change is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
Assign unique stable 32-bit OSPF router IDs to the two participating devices. This is a valid solution to a different Junos situation: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. It does not directly correct the specific failure evidence here: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The required targeted change is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
Design a supported OSPF virtual link over the common nonstub transit area and document its operational dependence. This is a valid solution to a different Junos situation: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. It does not directly correct the specific failure evidence here: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The required targeted change is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The proposed correction is: Align the intended OSPF network type and related election behavior on the two participating interfaces. Which observation MOST directly confirms this fault is resolved?
The neighbor database reaches Full with the expected point-to-point or broadcast behavior. This is the direct acceptance evidence for the observed failure: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The mechanism being validated is: OSPF network type determines neighbor and DR election behavior and must match the link design.
Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers. That would validate a different condition: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The decisive check for the current issue is: The neighbor database reaches Full with the expected point-to-point or broadcast behavior.
Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous. That would validate a different condition: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The decisive check for the current issue is: The neighbor database reaches Full with the expected point-to-point or broadcast behavior.
The remote area has a logical backbone adjacency through the intended transit area after validation. That would validate a different condition: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. The decisive check for the current issue is: The neighbor database reaches Full with the expected point-to-point or broadcast behavior.
A Junos engineer proposes this response: Align the intended OSPF network type and related election behavior on the two participating interfaces. The situation is: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. Which technical principle BEST justifies the response?
OSPF network type determines neighbor and DR election behavior and must match the link design. This is the controlling mechanism in the specific case: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. It predicts the acceptance result: The neighbor database reaches Full with the expected point-to-point or broadcast behavior.
OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation. This principle explains a separate situation: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. For this issue the relevant mechanism is: OSPF network type determines neighbor and DR election behavior and must match the link design.
OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes. This principle explains a separate situation: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. For this issue the relevant mechanism is: OSPF network type determines neighbor and DR election behavior and must match the link design.
OSPF virtual links can logically connect an area to the backbone through a qualifying transit area. This principle explains a separate situation: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. For this issue the relevant mechanism is: OSPF network type determines neighbor and DR election behavior and must match the link design.
Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. If the team bypasses or fails to implement the targeted correction (Align the intended OSPF network type and related election behavior on the two participating interfaces.), which direct operational risk or residual exposure is MOST relevant?
Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. This is the consequence linked to the observed situation: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. It is prevented by: Align the intended OSPF network type and related election behavior on the two participating interfaces. The underlying reason is: OSPF network type determines neighbor and DR election behavior and must match the link design.
An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. This risk belongs to a different operational problem: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The stated condition instead exposes this direct risk: Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. The appropriate mitigation is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. This risk belongs to a different operational problem: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The stated condition instead exposes this direct risk: Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. The appropriate mitigation is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
A virtual link through a stub transit area or an unavailable transit path cannot restore the backbone connection. This risk belongs to a different operational problem: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. The stated condition instead exposes this direct risk: Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. The appropriate mitigation is: Align the intended OSPF network type and related election behavior on the two participating interfaces.
An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. Which targeted engineering change is MOST directly justified by the observed evidence?
Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. This change specifically addresses the reported evidence: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The relevant protocol mechanism is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state. A decisive acceptance test would be: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
Permit the narrowly scoped OSPF control protocol traffic between authorized adjacent routers. This is a valid solution to a different Junos situation: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. It does not directly correct the specific failure evidence here: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The required targeted change is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.
Make the stub-area configuration consistent across every router attached to that area. This is a valid solution to a different Junos situation: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. It does not directly correct the specific failure evidence here: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The required targeted change is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.
Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This is a valid solution to a different Junos situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It does not directly correct the specific failure evidence here: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The required targeted change is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.
An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The proposed correction is: Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. Which observation MOST directly confirms this fault is resolved?
Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic. This is the direct acceptance evidence for the observed failure: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The mechanism being validated is: OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.
Captured OSPF Hellos and database exchange return and the neighbor reaches Full. That would validate a different condition: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements. That would validate a different condition: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
Please check your mailbox for a message from support@examlabs.com and follow the directions.