Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 1

Question 1

Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.
  2. Remove passive operation from only the transit OSPF interface that requires peer formation.
  3. Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.
  4. Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

Explanation

Correct Answer

A:

Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value. This change specifically addresses the reported evidence: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The relevant protocol mechanism is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged. A decisive acceptance test would be: The two neighbors advance to Full and database summaries no longer stall in ExStart.

Incorrect Answers

B:

Remove passive operation from only the transit OSPF interface that requires peer formation. This is a valid solution to a different Junos situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. It does not directly correct the specific failure evidence here: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The required targeted change is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

C:

Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. This is a valid solution to a different Junos situation: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. It does not directly correct the specific failure evidence here: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The required targeted change is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

D:

Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This is a valid solution to a different Junos situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It does not directly correct the specific failure evidence here: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The required targeted change is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

Question 2

Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The proposed correction is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value. Which observation MOST directly confirms this fault is resolved?

  1. Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent.
  2. The two neighbors advance to Full and database summaries no longer stall in ExStart.
  3. The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability.
  4. The elected DR and BDR are the intended routers following an actual election event.

Explanation

Correct Answer

B:

The two neighbors advance to Full and database summaries no longer stall in ExStart. This is the direct acceptance evidence for the observed failure: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. The mechanism being validated is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged.

Incorrect Answers

A:

Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent. That would validate a different condition: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The decisive check for the current issue is: The two neighbors advance to Full and database summaries no longer stall in ExStart.

C:

The OSPF route selects the desired cumulative lowest-cost next hop under equal reachability. That would validate a different condition: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The decisive check for the current issue is: The two neighbors advance to Full and database summaries no longer stall in ExStart.

D:

The elected DR and BDR are the intended routers following an actual election event. That would validate a different condition: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The decisive check for the current issue is: The two neighbors advance to Full and database summaries no longer stall in ExStart.

Question 3

A Junos engineer proposes this response: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value. The situation is: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. Which technical principle BEST justifies the response?

  1. A passive OSPF interface advertises its network but does not establish router neighbors there.
  2. OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.
  3. A DBD MTU check can prevent database synchronization even when Hellos are exchanged.
  4. OSPF DR election on a broadcast segment considers configured router interface priorities.

Explanation

Correct Answer

C:

A DBD MTU check can prevent database synchronization even when Hellos are exchanged. This is the controlling mechanism in the specific case: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. It predicts the acceptance result: The two neighbors advance to Full and database summaries no longer stall in ExStart.

Incorrect Answers

A:

A passive OSPF interface advertises its network but does not establish router neighbors there. This principle explains a separate situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. For this issue the relevant mechanism is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged.

B:

OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone. This principle explains a separate situation: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. For this issue the relevant mechanism is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged.

D:

OSPF DR election on a broadcast segment considers configured router interface priorities. This principle explains a separate situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. For this issue the relevant mechanism is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged.

Question 4

Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. If the team bypasses or fails to implement the targeted correction (Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.), which direct operational risk or residual exposure is MOST relevant?

  1. Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link.
  2. Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path.
  3. Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged.
  4. Ignoring an MTU mismatch can keep database exchange stalled; suppressing the MTU check can also hide oversized-packet problems.

Explanation

Correct Answer

D:

Ignoring an MTU mismatch can keep database exchange stalled; suppressing the MTU check can also hide oversized-packet problems. This is the consequence linked to the observed situation: Two OSPFv2 neighbors on a newly activated transit VLAN remain in ExStart, and the interface MTUs differ by 500 bytes. It is prevented by: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value. The underlying reason is: A DBD MTU check can prevent database synchronization even when Hellos are exchanged.

Incorrect Answers

A:

Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. This risk belongs to a different operational problem: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The stated condition instead exposes this direct risk: Ignoring an MTU mismatch can keep database exchange stalled; suppressing the MTU check can also hide oversized-packet problems. The appropriate mitigation is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

B:

Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. This risk belongs to a different operational problem: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The stated condition instead exposes this direct risk: Ignoring an MTU mismatch can keep database exchange stalled; suppressing the MTU check can also hide oversized-packet problems. The appropriate mitigation is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

C:

Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This risk belongs to a different operational problem: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The stated condition instead exposes this direct risk: Ignoring an MTU mismatch can keep database exchange stalled; suppressing the MTU check can also hide oversized-packet problems. The appropriate mitigation is: Align the OSPF-facing link MTUs after confirming the underlying Ethernet service supports the selected value.

Question 5

A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Set matching OSPF area membership for both sides of that transit adjacency.
  2. Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.
  3. Measure control-plane load and timer expiry before changing the OSPF neighbor configuration.
  4. Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

Explanation

Correct Answer

B:

Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. This change specifically addresses the reported evidence: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The relevant protocol mechanism is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation. A decisive acceptance test would be: Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.

Incorrect Answers

A:

Set matching OSPF area membership for both sides of that transit adjacency. This is a valid solution to a different Junos situation: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. It does not directly correct the specific failure evidence here: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The required targeted change is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

C:

Measure control-plane load and timer expiry before changing the OSPF neighbor configuration. This is a valid solution to a different Junos situation: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. It does not directly correct the specific failure evidence here: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The required targeted change is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

D:

Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. This is a valid solution to a different Junos situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. It does not directly correct the specific failure evidence here: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The required targeted change is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

Question 6

A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The proposed correction is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. Which observation MOST directly confirms this fault is resolved?

  1. Neighbor detail reports the intended common area and the area LSDB becomes consistent.
  2. Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic.
  3. Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.
  4. Only the allowlisted external prefixes appear in downstream external LSAs.

Explanation

Correct Answer

C:

Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers. This is the direct acceptance evidence for the observed failure: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The mechanism being validated is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

Incorrect Answers

A:

Neighbor detail reports the intended common area and the area LSDB becomes consistent. That would validate a different condition: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The decisive check for the current issue is: Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.

B:

Stabilized Hello reception prevents Dead timer expiry and adjacency flaps during peak traffic. That would validate a different condition: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The decisive check for the current issue is: Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.

D:

Only the allowlisted external prefixes appear in downstream external LSAs. That would validate a different condition: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The decisive check for the current issue is: Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.

Question 7

A Junos engineer proposes this response: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. The situation is: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. Which technical principle BEST justifies the response?

  1. OSPF adjacency requires compatible area identity at both ends of an interface.
  2. OSPF Dead intervals detect loss of expected Hellos independently of the physical link state.
  3. OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.
  4. OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

Explanation

Correct Answer

D:

OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation. This is the controlling mechanism in the specific case: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. It predicts the acceptance result: Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.

Incorrect Answers

A:

OSPF adjacency requires compatible area identity at both ends of an interface. This principle explains a separate situation: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. For this issue the relevant mechanism is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

B:

OSPF Dead intervals detect loss of expected Hellos independently of the physical link state. This principle explains a separate situation: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. For this issue the relevant mechanism is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

C:

OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. This principle explains a separate situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. For this issue the relevant mechanism is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

Question 8

A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. If the team bypasses or fails to implement the targeted correction (Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.), which direct operational risk or residual exposure is MOST relevant?

  1. An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB.
  2. Mismatched area membership blocks successful link-state adjacency despite IP connectivity.
  3. Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability.
  4. Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area.

Explanation

Correct Answer

A:

An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. This is the consequence linked to the observed situation: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. It is prevented by: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. The underlying reason is: OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.

Incorrect Answers

B:

Mismatched area membership blocks successful link-state adjacency despite IP connectivity. This risk belongs to a different operational problem: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The stated condition instead exposes this direct risk: An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. The appropriate mitigation is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

C:

Blindly raising timers can mask congestion rather than resolving recurrent neighbor instability. This risk belongs to a different operational problem: An OSPF neighbor repeatedly resets because a saturated control plane delays Hellos beyond the configured Dead timer. The stated condition instead exposes this direct risk: An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. The appropriate mitigation is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

D:

Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. This risk belongs to a different operational problem: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The stated condition instead exposes this direct risk: An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. The appropriate mitigation is: Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.

Question 9

Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Match the Hello and Dead interval values across both ends of the intended OSPF adjacency.
  2. Remove passive operation from only the transit OSPF interface that requires peer formation.
  3. Set matching OSPF area membership for both sides of that transit adjacency.
  4. Permit the narrowly scoped OSPF control protocol traffic between authorized adjacent routers.

Explanation

Correct Answer

C:

Set matching OSPF area membership for both sides of that transit adjacency. This change specifically addresses the reported evidence: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The relevant protocol mechanism is: OSPF adjacency requires compatible area identity at both ends of an interface. A decisive acceptance test would be: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Incorrect Answers

A:

Match the Hello and Dead interval values across both ends of the intended OSPF adjacency. This is a valid solution to a different Junos situation: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. It does not directly correct the specific failure evidence here: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The required targeted change is: Set matching OSPF area membership for both sides of that transit adjacency.

B:

Remove passive operation from only the transit OSPF interface that requires peer formation. This is a valid solution to a different Junos situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. It does not directly correct the specific failure evidence here: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The required targeted change is: Set matching OSPF area membership for both sides of that transit adjacency.

D:

Permit the narrowly scoped OSPF control protocol traffic between authorized adjacent routers. This is a valid solution to a different Junos situation: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. It does not directly correct the specific failure evidence here: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The required targeted change is: Set matching OSPF area membership for both sides of that transit adjacency.

Question 10

Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The proposed correction is: Set matching OSPF area membership for both sides of that transit adjacency. Which observation MOST directly confirms this fault is resolved?

  1. Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.
  2. Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent.
  3. Captured OSPF Hellos and database exchange return and the neighbor reaches Full.
  4. Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Explanation

Correct Answer

D:

Neighbor detail reports the intended common area and the area LSDB becomes consistent. This is the direct acceptance evidence for the observed failure: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The mechanism being validated is: OSPF adjacency requires compatible area identity at both ends of an interface.

Incorrect Answers

A:

Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers. That would validate a different condition: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

B:

Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent. That would validate a different condition: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

C:

Captured OSPF Hellos and database exchange return and the neighbor reaches Full. That would validate a different condition: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports