Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 2

Question 10

Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The proposed correction is: Set matching OSPF area membership for both sides of that transit adjacency. Which observation MOST directly confirms this fault is resolved?

  1. Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers.
  2. Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent.
  3. Captured OSPF Hellos and database exchange return and the neighbor reaches Full.
  4. Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Explanation

Correct Answer

D:

Neighbor detail reports the intended common area and the area LSDB becomes consistent. This is the direct acceptance evidence for the observed failure: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The mechanism being validated is: OSPF adjacency requires compatible area identity at both ends of an interface.

Incorrect Answers

A:

Neighbor state reaches Full and packet capture shows agreed Hello and Dead timers. That would validate a different condition: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

B:

Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent. That would validate a different condition: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

C:

Captured OSPF Hellos and database exchange return and the neighbor reaches Full. That would validate a different condition: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The decisive check for the current issue is: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Question 11

A Junos engineer proposes this response: Set matching OSPF area membership for both sides of that transit adjacency. The situation is: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. Which technical principle BEST justifies the response?

  1. OSPF adjacency requires compatible area identity at both ends of an interface.
  2. OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation.
  3. A passive OSPF interface advertises its network but does not establish router neighbors there.
  4. OSPF uses its own IP protocol for routing messages rather than TCP port sessions.

Explanation

Correct Answer

A:

OSPF adjacency requires compatible area identity at both ends of an interface. This is the controlling mechanism in the specific case: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. It predicts the acceptance result: Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Incorrect Answers

B:

OSPF neighbors must agree on relevant Hello packet parameters before adjacency formation. This principle explains a separate situation: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. For this issue the relevant mechanism is: OSPF adjacency requires compatible area identity at both ends of an interface.

C:

A passive OSPF interface advertises its network but does not establish router neighbors there. This principle explains a separate situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. For this issue the relevant mechanism is: OSPF adjacency requires compatible area identity at both ends of an interface.

D:

OSPF uses its own IP protocol for routing messages rather than TCP port sessions. This principle explains a separate situation: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. For this issue the relevant mechanism is: OSPF adjacency requires compatible area identity at both ends of an interface.

Question 12

Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. If the team bypasses or fails to implement the targeted correction (Set matching OSPF area membership for both sides of that transit adjacency.), which direct operational risk or residual exposure is MOST relevant?

  1. An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB.
  2. Mismatched area membership blocks successful link-state adjacency despite IP connectivity.
  3. Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link.
  4. A firewall that allows only TCP and ICMP can block OSPF while giving misleading reachability tests.

Explanation

Correct Answer

B:

Mismatched area membership blocks successful link-state adjacency despite IP connectivity. This is the consequence linked to the observed situation: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. It is prevented by: Set matching OSPF area membership for both sides of that transit adjacency. The underlying reason is: OSPF adjacency requires compatible area identity at both ends of an interface.

Incorrect Answers

A:

An unresolved Hello interval mismatch prevents the routers exchanging a synchronized LSDB. This risk belongs to a different operational problem: A pair of OSPFv2 routers on the same broadcast segment receive Hellos but remain unable to form an adjacency because one uses a 5-second Hello interval and the other 10 seconds. The stated condition instead exposes this direct risk: Mismatched area membership blocks successful link-state adjacency despite IP connectivity. The appropriate mitigation is: Set matching OSPF area membership for both sides of that transit adjacency.

C:

Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. This risk belongs to a different operational problem: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The stated condition instead exposes this direct risk: Mismatched area membership blocks successful link-state adjacency despite IP connectivity. The appropriate mitigation is: Set matching OSPF area membership for both sides of that transit adjacency.

D:

A firewall that allows only TCP and ICMP can block OSPF while giving misleading reachability tests. This risk belongs to a different operational problem: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The stated condition instead exposes this direct risk: Mismatched area membership blocks successful link-state adjacency despite IP connectivity. The appropriate mitigation is: Set matching OSPF area membership for both sides of that transit adjacency.

Question 13

A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
  2. Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.
  3. Check inter-area prefix LSAs and ABR route policy rather than assuming the missing prefixes are in router LSAs.
  4. Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

Explanation

Correct Answer

D:

Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. This change specifically addresses the reported evidence: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The relevant protocol mechanism is: OSPF DR election on a broadcast segment considers configured router interface priorities. A decisive acceptance test would be: The elected DR and BDR are the intended routers following an actual election event.

Incorrect Answers

A:

Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. This is a valid solution to a different Junos situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. It does not directly correct the specific failure evidence here: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The required targeted change is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

B:

Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. This is a valid solution to a different Junos situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. It does not directly correct the specific failure evidence here: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The required targeted change is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

C:

Check inter-area prefix LSAs and ABR route policy rather than assuming the missing prefixes are in router LSAs. This is a valid solution to a different Junos situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. It does not directly correct the specific failure evidence here: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The required targeted change is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

Question 14

A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The proposed correction is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. Which observation MOST directly confirms this fault is resolved?

  1. The elected DR and BDR are the intended routers following an actual election event.
  2. The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
  3. Only the allowlisted external prefixes appear in downstream external LSAs.
  4. The appropriate inter-area-prefix LSAs and accepted IPv6 routes appear for target networks.

Explanation

Correct Answer

A:

The elected DR and BDR are the intended routers following an actual election event. This is the direct acceptance evidence for the observed failure: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. The mechanism being validated is: OSPF DR election on a broadcast segment considers configured router interface priorities.

Incorrect Answers

B:

The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN. That would validate a different condition: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The decisive check for the current issue is: The elected DR and BDR are the intended routers following an actual election event.

C:

Only the allowlisted external prefixes appear in downstream external LSAs. That would validate a different condition: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The decisive check for the current issue is: The elected DR and BDR are the intended routers following an actual election event.

D:

The appropriate inter-area-prefix LSAs and accepted IPv6 routes appear for target networks. That would validate a different condition: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The decisive check for the current issue is: The elected DR and BDR are the intended routers following an actual election event.

Question 15

A Junos engineer proposes this response: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. The situation is: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. Which technical principle BEST justifies the response?

  1. Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
  2. OSPF DR election on a broadcast segment considers configured router interface priorities.
  3. OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.
  4. OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types.

Explanation

Correct Answer

B:

OSPF DR election on a broadcast segment considers configured router interface priorities. This is the controlling mechanism in the specific case: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It predicts the acceptance result: The elected DR and BDR are the intended routers following an actual election event.

Incorrect Answers

A:

Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface. This principle explains a separate situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. For this issue the relevant mechanism is: OSPF DR election on a broadcast segment considers configured router interface priorities.

C:

OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. This principle explains a separate situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. For this issue the relevant mechanism is: OSPF DR election on a broadcast segment considers configured router interface priorities.

D:

OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types. This principle explains a separate situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. For this issue the relevant mechanism is: OSPF DR election on a broadcast segment considers configured router interface priorities.

Question 16

A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. If the team bypasses or fails to implement the targeted correction (Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.), which direct operational risk or residual exposure is MOST relevant?

  1. Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface.
  2. Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area.
  3. Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged.
  4. Looking only for IPv6 prefixes in OSPFv3 router LSAs can hide the actual prefix propagation problem.

Explanation

Correct Answer

C:

Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. This is the consequence linked to the observed situation: A multiaccess OSPF LAN has the wrong device acting as designated router after an access switch was replaced. It is prevented by: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate. The underlying reason is: OSPF DR election on a broadcast segment considers configured router interface priorities.

Incorrect Answers

A:

Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. This risk belongs to a different operational problem: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The stated condition instead exposes this direct risk: Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. The appropriate mitigation is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

B:

Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. This risk belongs to a different operational problem: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The stated condition instead exposes this direct risk: Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. The appropriate mitigation is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

D:

Looking only for IPv6 prefixes in OSPFv3 router LSAs can hide the actual prefix propagation problem. This risk belongs to a different operational problem: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The stated condition instead exposes this direct risk: Assuming a changed priority immediately preempts the existing DR can leave the old election result unchanged. The appropriate mitigation is: Tune the OSPF interface priority on the intended DR candidate and trigger an orderly election if appropriate.

Question 17

An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Make the stub-area configuration consistent across every router attached to that area.
  2. Check inter-area prefix LSAs and ABR route policy rather than assuming the missing prefixes are in router LSAs.
  3. Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
  4. Check Junos OSPF import policy and route hidden/inactive reasons in the routing table.

Explanation

Correct Answer

A:

Make the stub-area configuration consistent across every router attached to that area. This change specifically addresses the reported evidence: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The relevant protocol mechanism is: The OSPF stub capability must agree among routers in the same area. A decisive acceptance test would be: Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.

Incorrect Answers

B:

Check inter-area prefix LSAs and ABR route policy rather than assuming the missing prefixes are in router LSAs. This is a valid solution to a different Junos situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. It does not directly correct the specific failure evidence here: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The required targeted change is: Make the stub-area configuration consistent across every router attached to that area.

C:

Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. This is a valid solution to a different Junos situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. It does not directly correct the specific failure evidence here: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The required targeted change is: Make the stub-area configuration consistent across every router attached to that area.

D:

Check Junos OSPF import policy and route hidden/inactive reasons in the routing table. This is a valid solution to a different Junos situation: After a maintenance change, OSPFv2 routes vanish from inet.0 but the protocol neighbor remains Full and LSAs are present. It does not directly correct the specific failure evidence here: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The required targeted change is: Make the stub-area configuration consistent across every router attached to that area.

Question 18

An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The proposed correction is: Make the stub-area configuration consistent across every router attached to that area. Which observation MOST directly confirms this fault is resolved?

  1. The appropriate inter-area-prefix LSAs and accepted IPv6 routes appear for target networks.
  2. Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.
  3. The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
  4. A permitted candidate installs in inet.0 or reveals an explicit, intended policy rejection.

Explanation

Correct Answer

B:

Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements. This is the direct acceptance evidence for the observed failure: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. The mechanism being validated is: The OSPF stub capability must agree among routers in the same area.

Incorrect Answers

A:

The appropriate inter-area-prefix LSAs and accepted IPv6 routes appear for target networks. That would validate a different condition: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The decisive check for the current issue is: Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.

C:

The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN. That would validate a different condition: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The decisive check for the current issue is: Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.

D:

A permitted candidate installs in inet.0 or reveals an explicit, intended policy rejection. That would validate a different condition: After a maintenance change, OSPFv2 routes vanish from inet.0 but the protocol neighbor remains Full and LSAs are present. The decisive check for the current issue is: Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.

Question 19

A Junos engineer proposes this response: Make the stub-area configuration consistent across every router attached to that area. The situation is: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. Which technical principle BEST justifies the response?

  1. OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types.
  2. Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
  3. The OSPF stub capability must agree among routers in the same area.
  4. Junos import policies and route selection can affect installation independently of LSDB adjacency.

Explanation

Correct Answer

C:

The OSPF stub capability must agree among routers in the same area. This is the controlling mechanism in the specific case: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. It predicts the acceptance result: Neighbor adjacencies are Full and the stub area avoids the prohibited external LSA advertisements.

Incorrect Answers

A:

OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types. This principle explains a separate situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. For this issue the relevant mechanism is: The OSPF stub capability must agree among routers in the same area.

B:

Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface. This principle explains a separate situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. For this issue the relevant mechanism is: The OSPF stub capability must agree among routers in the same area.

D:

Junos import policies and route selection can affect installation independently of LSDB adjacency. This principle explains a separate situation: After a maintenance change, OSPFv2 routes vanish from inet.0 but the protocol neighbor remains Full and LSAs are present. For this issue the relevant mechanism is: The OSPF stub capability must agree among routers in the same area.

Question 20

An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. If the team bypasses or fails to implement the targeted correction (Make the stub-area configuration consistent across every router attached to that area.), which direct operational risk or residual exposure is MOST relevant?

  1. Looking only for IPv6 prefixes in OSPFv3 router LSAs can hide the actual prefix propagation problem.
  2. Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface.
  3. Restarting healthy neighbors cannot correct a routing policy that rejects desired learned routes.
  4. A mismatched area capability or external LSA leakage prevents intended stub operation.

Explanation

Correct Answer

D:

A mismatched area capability or external LSA leakage prevents intended stub operation. This is the consequence linked to the observed situation: An OSPFv2 area is designed as stub but one internal router still treats it as a normal area, preventing stable neighbor operation. It is prevented by: Make the stub-area configuration consistent across every router attached to that area. The underlying reason is: The OSPF stub capability must agree among routers in the same area.

Incorrect Answers

A:

Looking only for IPv6 prefixes in OSPFv3 router LSAs can hide the actual prefix propagation problem. This risk belongs to a different operational problem: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The stated condition instead exposes this direct risk: A mismatched area capability or external LSA leakage prevents intended stub operation. The appropriate mitigation is: Make the stub-area configuration consistent across every router attached to that area.

B:

Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. This risk belongs to a different operational problem: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The stated condition instead exposes this direct risk: A mismatched area capability or external LSA leakage prevents intended stub operation. The appropriate mitigation is: Make the stub-area configuration consistent across every router attached to that area.

C:

Restarting healthy neighbors cannot correct a routing policy that rejects desired learned routes. This risk belongs to a different operational problem: After a maintenance change, OSPFv2 routes vanish from inet.0 but the protocol neighbor remains Full and LSAs are present. The stated condition instead exposes this direct risk: A mismatched area capability or external LSA leakage prevents intended stub operation. The appropriate mitigation is: Make the stub-area configuration consistent across every router attached to that area.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports