JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
BGP session establishment fails after one side is configured for the wrong remote autonomous system number. The proposed correction is: Correct the neighbor's expected peer AS in the Junos BGP group configuration. Which observation MOST directly confirms this fault is resolved?
The Open exchange succeeds and neighbor state reaches Established for the intended ASN. This is the direct acceptance evidence for the observed failure: BGP session establishment fails after one side is configured for the wrong remote autonomous system number. The mechanism being validated is: BGP OPEN messages validate negotiated peer AS identity as part of session setup.
The accepted received AS path no longer violates the intended AS-loop policy at the upstream peer. That would validate a different condition: An EBGP peer unexpectedly rejects local advertisements after the enterprise appends its own AS number twice in an outbound policy. The decisive check for the current issue is: The Open exchange succeeds and neighbor state reaches Established for the intended ASN.
The BGP session reports inet6 capability and advertises the expected IPv6 prefix. That would validate a different condition: An IPv6-only prefix should be exchanged over an existing BGP neighbor but the group currently negotiates only inet unicast. The decisive check for the current issue is: The Open exchange succeeds and neighbor state reaches Established for the intended ASN.
The peer receives precisely the eligible prefix and withdraws it when export conditions fail. That would validate a different condition: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. The decisive check for the current issue is: The Open exchange succeeds and neighbor state reaches Established for the intended ASN.
A Junos engineer proposes this response: Correct the neighbor's expected peer AS in the Junos BGP group configuration. The situation is: BGP session establishment fails after one side is configured for the wrong remote autonomous system number. Which technical principle BEST justifies the response?
BGP OPEN messages validate negotiated peer AS identity as part of session setup. This is the controlling mechanism in the specific case: BGP session establishment fails after one side is configured for the wrong remote autonomous system number. It predicts the acceptance result: The Open exchange succeeds and neighbor state reaches Established for the intended ASN.
BGP AS-path records traversed autonomous systems and supports AS-loop detection. This principle explains a separate situation: An EBGP peer unexpectedly rejects local advertisements after the enterprise appends its own AS number twice in an outbound policy. For this issue the relevant mechanism is: BGP OPEN messages validate negotiated peer AS identity as part of session setup.
BGP address families distinguish IPv4 inet from IPv6 inet6 reachability exchange. This principle explains a separate situation: An IPv6-only prefix should be exchanged over an existing BGP neighbor but the group currently negotiates only inet unicast. For this issue the relevant mechanism is: BGP OPEN messages validate negotiated peer AS identity as part of session setup.
Junos BGP export policy controls which locally eligible routes enter peer advertisements. This principle explains a separate situation: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. For this issue the relevant mechanism is: BGP OPEN messages validate negotiated peer AS identity as part of session setup.
BGP session establishment fails after one side is configured for the wrong remote autonomous system number. If the team bypasses or fails to implement the targeted correction (Correct the neighbor's expected peer AS in the Junos BGP group configuration.), which direct operational risk or residual exposure is MOST relevant?
A wrong remote AS expectation causes BGP session resets despite basic TCP reachability. This is the consequence linked to the observed situation: BGP session establishment fails after one side is configured for the wrong remote autonomous system number. It is prevented by: Correct the neighbor's expected peer AS in the Junos BGP group configuration. The underlying reason is: BGP OPEN messages validate negotiated peer AS identity as part of session setup.
Careless prepending that introduces the recipient's own AS can cause an advertised route to be rejected. This risk belongs to a different operational problem: An EBGP peer unexpectedly rejects local advertisements after the enterprise appends its own AS number twice in an outbound policy. The stated condition instead exposes this direct risk: A wrong remote AS expectation causes BGP session resets despite basic TCP reachability. The appropriate mitigation is: Correct the neighbor's expected peer AS in the Junos BGP group configuration.
A working IPv4 BGP session does not imply IPv6 unicast NLRI negotiation is enabled. This risk belongs to a different operational problem: An IPv6-only prefix should be exchanged over an existing BGP neighbor but the group currently negotiates only inet unicast. The stated condition instead exposes this direct risk: A wrong remote AS expectation causes BGP session resets despite basic TCP reachability. The appropriate mitigation is: Correct the neighbor's expected peer AS in the Junos BGP group configuration.
An unconditional export can leak prefixes when the intended backing reachability disappears. This risk belongs to a different operational problem: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. The stated condition instead exposes this direct risk: A wrong remote AS expectation causes BGP session resets despite basic TCP reachability. The appropriate mitigation is: Correct the neighbor's expected peer AS in the Junos BGP group configuration.
An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. Which targeted engineering change is MOST directly justified by the observed evidence?
Configure appropriate EBGP multihop with reachability and the proper peer source address. This change specifically addresses the reported evidence: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The relevant protocol mechanism is: EBGP multihop supports peering across a routed path beyond the directly connected link. A decisive acceptance test would be: The multihop neighbor establishes across its routed intermediary and reports expected source addresses.
Restore a usable unicast route to the BGP next hop before trying to override local preference. This is a valid solution to a different Junos situation: A route from an EBGP peer shows a valid next-hop address that cannot be resolved to any active transport route. It does not directly correct the specific failure evidence here: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The required targeted change is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
Apply an appropriate peer or policy AS-path limit while preserving explicitly permitted customer destinations. This is a valid solution to a different Junos situation: One EBGP customer sends a path with too many AS numbers and the provider wants a protective bound on accepted AS paths. It does not directly correct the specific failure evidence here: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The required targeted change is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
Trigger and verify an appropriate policy refresh or update mechanism supported by the BGP peers. This is a valid solution to a different Junos situation: A new BGP policy changes outbound community values, but previously advertised routes still display old metadata at the downstream peer. It does not directly correct the specific failure evidence here: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The required targeted change is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The proposed correction is: Configure appropriate EBGP multihop with reachability and the proper peer source address. Which observation MOST directly confirms this fault is resolved?
The multihop neighbor establishes across its routed intermediary and reports expected source addresses. This is the direct acceptance evidence for the observed failure: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The mechanism being validated is: EBGP multihop supports peering across a routed path beyond the directly connected link.
The next hop resolves and the received BGP prefix becomes eligible for active selection. That would validate a different condition: A route from an EBGP peer shows a valid next-hop address that cannot be resolved to any active transport route. The decisive check for the current issue is: The multihop neighbor establishes across its routed intermediary and reports expected source addresses.
Over-limit updates are handled according to the configured guard and valid routes remain permitted. That would validate a different condition: One EBGP customer sends a path with too many AS numbers and the provider wants a protective bound on accepted AS paths. The decisive check for the current issue is: The multihop neighbor establishes across its routed intermediary and reports expected source addresses.
The downstream advertised route shows the updated community without unplanned neighbor disruption. That would validate a different condition: A new BGP policy changes outbound community values, but previously advertised routes still display old metadata at the downstream peer. The decisive check for the current issue is: The multihop neighbor establishes across its routed intermediary and reports expected source addresses.
A Junos engineer proposes this response: Configure appropriate EBGP multihop with reachability and the proper peer source address. The situation is: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. Which technical principle BEST justifies the response?
EBGP multihop supports peering across a routed path beyond the directly connected link. This is the controlling mechanism in the specific case: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. It predicts the acceptance result: The multihop neighbor establishes across its routed intermediary and reports expected source addresses.
BGP next-hop reachability must be established before a route can be used for forwarding. This principle explains a separate situation: A route from an EBGP peer shows a valid next-hop address that cannot be resolved to any active transport route. For this issue the relevant mechanism is: EBGP multihop supports peering across a routed path beyond the directly connected link.
BGP AS-path validation and peer protection can constrain anomalously long path information. This principle explains a separate situation: One EBGP customer sends a path with too many AS numbers and the provider wants a protective bound on accepted AS paths. For this issue the relevant mechanism is: EBGP multihop supports peering across a routed path beyond the directly connected link.
BGP advertisements reflect routing policy and may require controlled re-evaluation after changes. This principle explains a separate situation: A new BGP policy changes outbound community values, but previously advertised routes still display old metadata at the downstream peer. For this issue the relevant mechanism is: EBGP multihop supports peering across a routed path beyond the directly connected link.
An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. If the team bypasses or fails to implement the targeted correction (Configure appropriate EBGP multihop with reachability and the proper peer source address.), which direct operational risk or residual exposure is MOST relevant?
Failing to account for hop count and source address can prevent the intended multihop BGP session. This is the consequence linked to the observed situation: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. It is prevented by: Configure appropriate EBGP multihop with reachability and the proper peer source address. The underlying reason is: EBGP multihop supports peering across a routed path beyond the directly connected link.
A high-preference route with an unreachable next hop cannot become a viable forwarding path. This risk belongs to a different operational problem: A route from an EBGP peer shows a valid next-hop address that cannot be resolved to any active transport route. The stated condition instead exposes this direct risk: Failing to account for hop count and source address can prevent the intended multihop BGP session. The appropriate mitigation is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
Accepting unrestricted anomalous paths can consume resources or spread bad routing information. This risk belongs to a different operational problem: One EBGP customer sends a path with too many AS numbers and the provider wants a protective bound on accepted AS paths. The stated condition instead exposes this direct risk: Failing to account for hop count and source address can prevent the intended multihop BGP session. The appropriate mitigation is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
Assuming a locally changed policy is already reflected remotely can conceal stale announcements. This risk belongs to a different operational problem: A new BGP policy changes outbound community values, but previously advertised routes still display old metadata at the downstream peer. The stated condition instead exposes this direct risk: Failing to account for hop count and source address can prevent the intended multihop BGP session. The appropriate mitigation is: Configure appropriate EBGP multihop with reachability and the proper peer source address.
An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. Which targeted engineering change is MOST directly justified by the observed evidence?
Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships. This change specifically addresses the reported evidence: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The relevant protocol mechanism is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection. A decisive acceptance test would be: The downstream IBGP client learns the intended route without creating an unintended loop.
Review route reflector cluster identifiers and reflected route attributes for the actual intended topology. This is a valid solution to a different Junos situation: A route reflector cluster loops reflected routing information after newly created reflectors were assigned inconsistent cluster identities. It does not directly correct the specific failure evidence here: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The required targeted change is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
Use a term-based BGP export policy that matches the authorized active route and accepted prefix. This is a valid solution to a different Junos situation: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. It does not directly correct the specific failure evidence here: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The required targeted change is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
Confirm the appropriate family and community propagation settings on the BGP peering path. This is a valid solution to a different Junos situation: Two routers share BGP routes but their intended extended-community values are absent at a downstream policy boundary. It does not directly correct the specific failure evidence here: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The required targeted change is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The proposed correction is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships. Which observation MOST directly confirms this fault is resolved?
The downstream IBGP client learns the intended route without creating an unintended loop. This is the direct acceptance evidence for the observed failure: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. The mechanism being validated is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection.
Cluster-list and originator attributes prevent a reflected route being accepted back into its origin cluster. That would validate a different condition: A route reflector cluster loops reflected routing information after newly created reflectors were assigned inconsistent cluster identities. The decisive check for the current issue is: The downstream IBGP client learns the intended route without creating an unintended loop.
The peer receives precisely the eligible prefix and withdraws it when export conditions fail. That would validate a different condition: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. The decisive check for the current issue is: The downstream IBGP client learns the intended route without creating an unintended loop.
The intended extended-community values appear on the received route and relevant policies match them. That would validate a different condition: Two routers share BGP routes but their intended extended-community values are absent at a downstream policy boundary. The decisive check for the current issue is: The downstream IBGP client learns the intended route without creating an unintended loop.
A Junos engineer proposes this response: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships. The situation is: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. Which technical principle BEST justifies the response?
IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection. This is the controlling mechanism in the specific case: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. It predicts the acceptance result: The downstream IBGP client learns the intended route without creating an unintended loop.
BGP reflection uses originator and cluster-list information to help prevent reflection loops. This principle explains a separate situation: A route reflector cluster loops reflected routing information after newly created reflectors were assigned inconsistent cluster identities. For this issue the relevant mechanism is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection.
Junos BGP export policy controls which locally eligible routes enter peer advertisements. This principle explains a separate situation: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. For this issue the relevant mechanism is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection.
Extended communities provide structured BGP route metadata for supported applications and policies. This principle explains a separate situation: Two routers share BGP routes but their intended extended-community values are absent at a downstream policy boundary. For this issue the relevant mechanism is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection.
An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. If the team bypasses or fails to implement the targeted correction (Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.), which direct operational risk or residual exposure is MOST relevant?
Assuming IBGP is transitive through any intermediate speaker can strand learned prefixes. This is the consequence linked to the observed situation: An IBGP router fails to advertise a route received from one IBGP peer to another IBGP peer in a non-route-reflected full mesh gap. It is prevented by: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships. The underlying reason is: IBGP split-horizon advertisement rules prevent ordinary IBGP-to-IBGP readvertisement without reflection.
An inconsistent reflection design can suppress valid paths or propagate redundant route updates. This risk belongs to a different operational problem: A route reflector cluster loops reflected routing information after newly created reflectors were assigned inconsistent cluster identities. The stated condition instead exposes this direct risk: Assuming IBGP is transitive through any intermediate speaker can strand learned prefixes. The appropriate mitigation is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
An unconditional export can leak prefixes when the intended backing reachability disappears. This risk belongs to a different operational problem: A partner asks a Junos edge to advertise a longer prefix only when a certain route is present in the active routing table. The stated condition instead exposes this direct risk: Assuming IBGP is transitive through any intermediate speaker can strand learned prefixes. The appropriate mitigation is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
Losing required extended-community metadata can break downstream tagging or route-target policy. This risk belongs to a different operational problem: Two routers share BGP routes but their intended extended-community values are absent at a downstream policy boundary. The stated condition instead exposes this direct risk: Assuming IBGP is transitive through any intermediate speaker can strand learned prefixes. The appropriate mitigation is: Deploy a correctly designed route reflector or the necessary full-mesh IBGP peering relationships.
Please check your mailbox for a message from support@examlabs.com and follow the directions.