JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The proposed correction is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. Which observation MOST directly confirms this fault is resolved?
The multicast state shows the exact (source,group) pair requested by the receiver. This is the direct acceptance evidence for the observed failure: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The mechanism being validated is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
The multicast entry includes the named source and excludes other senders for the same group. That would validate a different condition: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. That would validate a different condition: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
A Junos engineer proposes this response: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. The situation is: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. Which technical principle BEST justifies the response?
IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM. This is the controlling mechanism in the specific case: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. It predicts the acceptance result: The multicast state shows the exact (source,group) pair requested by the receiver.
IGMPv3 INCLUDE lists express positive source membership for source-specific reception. This principle explains a separate situation: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. For this issue the relevant mechanism is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
IPv4 SSM requires source-specific membership information for the intended stream. This principle explains a separate situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. For this issue the relevant mechanism is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
PIM forwarding-state construction requires participating multicast routers along the path. This principle explains a separate situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. For this issue the relevant mechanism is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. If the team bypasses or fails to implement the targeted correction (Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.), which direct operational risk or residual exposure is MOST relevant?
Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. This is the consequence linked to the observed situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. It is prevented by: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. The underlying reason is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. This risk belongs to a different operational problem: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. The stated condition instead exposes this direct risk: Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. The appropriate mitigation is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
Group-only joins without mapping cannot unambiguously select a source for the SSM group. This risk belongs to a different operational problem: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The stated condition instead exposes this direct risk: Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. The appropriate mitigation is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. This risk belongs to a different operational problem: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The stated condition instead exposes this direct risk: Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. The appropriate mitigation is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. Which targeted engineering change is MOST directly justified by the observed evidence?
Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP. This change specifically addresses the reported evidence: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The relevant protocol mechanism is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree. A decisive acceptance test would be: The requested (S,G) stream reaches subscribers directly along its source tree.
Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. This is a valid solution to a different Junos situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It does not directly correct the specific failure evidence here: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The required targeted change is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
Deploy supported Anycast RP peers with matching anycast address and appropriate source-discovery method. This is a valid solution to a different Junos situation: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. It does not directly correct the specific failure evidence here: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The required targeted change is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
Configure and verify the necessary MSDP source-active exchange between the intended RPs. This is a valid solution to a different Junos situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. It does not directly correct the specific failure evidence here: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The required targeted change is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The proposed correction is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP. Which observation MOST directly confirms this fault is resolved?
The requested (S,G) stream reaches subscribers directly along its source tree. This is the direct acceptance evidence for the observed failure: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The mechanism being validated is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree.
The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. That would validate a different condition: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The decisive check for the current issue is: The requested (S,G) stream reaches subscribers directly along its source tree.
The multicast entry includes the named source and excludes other senders for the same group. That would validate a different condition: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. The decisive check for the current issue is: The requested (S,G) stream reaches subscribers directly along its source tree.
Each RP learns the relevant remote active-source advertisements and receivers can join their sources. That would validate a different condition: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The decisive check for the current issue is: The requested (S,G) stream reaches subscribers directly along its source tree.
A Junos engineer proposes this response: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP. The situation is: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. Which technical principle BEST justifies the response?
PIM SSM joins known sources and does not require RP discovery or an ASM shared tree. This is the controlling mechanism in the specific case: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. It predicts the acceptance result: The requested (S,G) stream reaches subscribers directly along its source tree.
IPv4 SSM requires source-specific membership information for the intended stream. This principle explains a separate situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. For this issue the relevant mechanism is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree.
IGMPv3 INCLUDE lists express positive source membership for source-specific reception. This principle explains a separate situation: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. For this issue the relevant mechanism is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree.
MSDP can convey active-source information across separate RP domains or Anycast RP peers. This principle explains a separate situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. For this issue the relevant mechanism is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree.
An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. If the team bypasses or fails to implement the targeted correction (Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.), which direct operational risk or residual exposure is MOST relevant?
Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. This is the consequence linked to the observed situation: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. It is prevented by: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP. The underlying reason is: PIM SSM joins known sources and does not require RP discovery or an ASM shared tree.
Group-only joins without mapping cannot unambiguously select a source for the SSM group. This risk belongs to a different operational problem: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The stated condition instead exposes this direct risk: Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. The appropriate mitigation is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. This risk belongs to a different operational problem: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. The stated condition instead exposes this direct risk: Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. The appropriate mitigation is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
An Anycast address alone does not synchronize active-source discovery in an MSDP-based design. This risk belongs to a different operational problem: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The stated condition instead exposes this direct risk: Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. The appropriate mitigation is: Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP.
An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. Which targeted engineering change is MOST directly justified by the observed evidence?
Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. This change specifically addresses the reported evidence: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The relevant protocol mechanism is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM. A decisive acceptance test would be: The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
Deploy supported Anycast RP peers with matching anycast address and appropriate source-discovery method. This is a valid solution to a different Junos situation: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. It does not directly correct the specific failure evidence here: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The required targeted change is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. This is a valid solution to a different Junos situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. It does not directly correct the specific failure evidence here: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The required targeted change is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
Configure and verify the necessary MSDP source-active exchange between the intended RPs. This is a valid solution to a different Junos situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. It does not directly correct the specific failure evidence here: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The required targeted change is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The proposed correction is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. Which observation MOST directly confirms this fault is resolved?
The last-hop router discovers the RP and joins the (*,G) shared distribution tree. This is the direct acceptance evidence for the observed failure: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The mechanism being validated is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
An RP outage causes the PIM routers to resolve and use a surviving anycast RP as designed. That would validate a different condition: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. The decisive check for the current issue is: The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
The group's receiver interface appears in IGMP membership and expected multicast forwarding state. That would validate a different condition: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The decisive check for the current issue is: The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
Each RP learns the relevant remote active-source advertisements and receivers can join their sources. That would validate a different condition: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The decisive check for the current issue is: The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
A Junos engineer proposes this response: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. The situation is: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. Which technical principle BEST justifies the response?
PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM. This is the controlling mechanism in the specific case: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. It predicts the acceptance result: The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
Anycast RP provides redundant shared-tree rendezvous service using multiple RP nodes. This principle explains a separate situation: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. For this issue the relevant mechanism is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers. This principle explains a separate situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. For this issue the relevant mechanism is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
IGMPv3 INCLUDE lists express positive source membership for source-specific reception. This principle explains a separate situation: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. For this issue the relevant mechanism is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. If the team bypasses or fails to implement the targeted correction (Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.), which direct operational risk or residual exposure is MOST relevant?
Without an RP for the ASM group, the normal shared tree cannot be established. This is the consequence linked to the observed situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. It is prevented by: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. The underlying reason is: PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
A single physical RP remains a service failure point for ASM multicast groups. This risk belongs to a different operational problem: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. The stated condition instead exposes this direct risk: Without an RP for the ASM group, the normal shared tree cannot be established. The appropriate mitigation is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
With no valid receiver membership, the router may not build the intended downstream multicast branch. This risk belongs to a different operational problem: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The stated condition instead exposes this direct risk: Without an RP for the ASM group, the normal shared tree cannot be established. The appropriate mitigation is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
An Anycast address alone does not synchronize active-source discovery in an MSDP-based design. This risk belongs to a different operational problem: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The stated condition instead exposes this direct risk: Without an RP for the ASM group, the normal shared tree cannot be established. The appropriate mitigation is: Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
Please check your mailbox for a message from support@examlabs.com and follow the directions.