JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
After a redundancy event, BGP still prefers an old path whose underlying transport next hop stopped resolving in the new IGP topology. If the team bypasses or fails to implement the targeted correction (Inspect next-hop recursive resolution and refresh the relevant IGP reachability before tuning BGP attributes.), which direct operational risk or residual exposure is MOST relevant?
Keeping an invalid recursive next hop can create a control-plane route without usable forwarding. This is the consequence linked to the observed situation: After a redundancy event, BGP still prefers an old path whose underlying transport next hop stopped resolving in the new IGP topology. It is prevented by: Inspect next-hop recursive resolution and refresh the relevant IGP reachability before tuning BGP attributes. The underlying reason is: BGP next-hop resolution depends on current reachability supplied by the routing table.
Tuning IGP cost when local preference differs will not change the selected BGP path. This risk belongs to a different operational problem: The enterprise wants to steer traffic toward the upstream with lower IGP cost only after local preference and AS-path checks tie. The stated condition instead exposes this direct risk: Keeping an invalid recursive next hop can create a control-plane route without usable forwarding. The appropriate mitigation is: Inspect next-hop recursive resolution and refresh the relevant IGP reachability before tuning BGP attributes.
Failing to account for hop count and source address can prevent the intended multihop BGP session. This risk belongs to a different operational problem: An EBGP neighbor has a reachable loopback address two IP hops away, but a default one-hop peering design cannot establish the session. The stated condition instead exposes this direct risk: Keeping an invalid recursive next hop can create a control-plane route without usable forwarding. The appropriate mitigation is: Inspect next-hop recursive resolution and refresh the relevant IGP reachability before tuning BGP attributes.
Losing required extended-community metadata can break downstream tagging or route-target policy. This risk belongs to a different operational problem: Two routers share BGP routes but their intended extended-community values are absent at a downstream policy boundary. The stated condition instead exposes this direct risk: Keeping an invalid recursive next hop can create a control-plane route without usable forwarding. The appropriate mitigation is: Inspect next-hop recursive resolution and refresh the relevant IGP reachability before tuning BGP attributes.
Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. Which targeted engineering change is MOST directly justified by the observed evidence?
Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps. This change specifically addresses the reported evidence: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The relevant protocol mechanism is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths. A decisive acceptance test would be: The documented late tie-break identifies the selected peer after earlier selection criteria are equal.
Prefer the valid shorter AS path after earlier path-selection criteria tie. This is a valid solution to a different Junos situation: Two BGP routes are equal in local preference, but one includes three AS hops and the other one, and no earlier attribute resolves the comparison. It does not directly correct the specific failure evidence here: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The required targeted change is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
Prefer the valid path with higher local preference before comparing AS-path length under Junos BGP selection. This is a valid solution to a different Junos situation: Two valid BGP paths for one prefix have different local preference attributes, 180 on ISP-A and 100 on ISP-B, but the operator chooses the shorter AS path on B. It does not directly correct the specific failure evidence here: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The required targeted change is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
Assign a higher local preference to the primary ISP routes at ingress and propagate it internally. This is a valid solution to a different Junos situation: An enterprise wants every internal BGP router to favor the primary upstream even though that primary route traverses more external autonomous systems. It does not directly correct the specific failure evidence here: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The required targeted change is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The proposed correction is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps. Which observation MOST directly confirms this fault is resolved?
The documented late tie-break identifies the selected peer after earlier selection criteria are equal. This is the direct acceptance evidence for the observed failure: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. The mechanism being validated is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths.
The path with one AS hop becomes the BGP best path under the controlled comparison. That would validate a different condition: Two BGP routes are equal in local preference, but one includes three AS hops and the other one, and no earlier attribute resolves the comparison. The decisive check for the current issue is: The documented late tie-break identifies the selected peer after earlier selection criteria are equal.
The best-path display chooses ISP-A when reachability and earlier selection criteria are satisfied. That would validate a different condition: Two valid BGP paths for one prefix have different local preference attributes, 180 on ISP-A and 100 on ISP-B, but the operator chooses the shorter AS path on B. The decisive check for the current issue is: The documented late tie-break identifies the selected peer after earlier selection criteria are equal.
IBGP speakers select the preferred primary egress consistently for the target prefixes. That would validate a different condition: An enterprise wants every internal BGP router to favor the primary upstream even though that primary route traverses more external autonomous systems. The decisive check for the current issue is: The documented late tie-break identifies the selected peer after earlier selection criteria are equal.
A Junos engineer proposes this response: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps. The situation is: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. Which technical principle BEST justifies the response?
Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths. This is the controlling mechanism in the specific case: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. It predicts the acceptance result: The documented late tie-break identifies the selected peer after earlier selection criteria are equal.
BGP AS-path length acts as a path-selection discriminator after local preference. This principle explains a separate situation: Two BGP routes are equal in local preference, but one includes three AS hops and the other one, and no earlier attribute resolves the comparison. For this issue the relevant mechanism is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths.
Junos BGP compares higher LOCAL_PREF before shorter AS-path in ordinary best-path selection. This principle explains a separate situation: Two valid BGP paths for one prefix have different local preference attributes, 180 on ISP-A and 100 on ISP-B, but the operator chooses the shorter AS path on B. For this issue the relevant mechanism is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths.
LOCAL_PREF is propagated inside the AS and selects the preferred external exit among reachable paths. This principle explains a separate situation: An enterprise wants every internal BGP router to favor the primary upstream even though that primary route traverses more external autonomous systems. For this issue the relevant mechanism is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths.
Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. If the team bypasses or fails to implement the targeted correction (Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.), which direct operational risk or residual exposure is MOST relevant?
Changing an unrelated attribute can hide why the original equal paths were selected differently. This is the consequence linked to the observed situation: Two otherwise comparable BGP candidates remain tied on main attributes, but a router ID tie-break selects an unexpected peer. It is prevented by: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps. The underlying reason is: Late BGP deterministic tie-breaks apply only when the preceding attributes do not distinguish paths.
Ignoring AS-path differences can produce a different best path than policy designers expect. This risk belongs to a different operational problem: Two BGP routes are equal in local preference, but one includes three AS hops and the other one, and no earlier attribute resolves the comparison. The stated condition instead exposes this direct risk: Changing an unrelated attribute can hide why the original equal paths were selected differently. The appropriate mitigation is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
Ignoring local preference can produce a wrong expected egress and incorrect policy remediation. This risk belongs to a different operational problem: Two valid BGP paths for one prefix have different local preference attributes, 180 on ISP-A and 100 on ISP-B, but the operator chooses the shorter AS path on B. The stated condition instead exposes this direct risk: Changing an unrelated attribute can hide why the original equal paths were selected differently. The appropriate mitigation is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
Adjusting only MED on external advertisements may not control the enterprise's own outbound choice. This risk belongs to a different operational problem: An enterprise wants every internal BGP router to favor the primary upstream even though that primary route traverses more external autonomous systems. The stated condition instead exposes this direct risk: Changing an unrelated attribute can hide why the original equal paths were selected differently. The appropriate mitigation is: Verify the full BGP path-selection trace including late router-ID and peer-address tie-break steps.
An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. Which targeted engineering change is MOST directly justified by the observed evidence?
Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. This change specifically addresses the reported evidence: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The relevant protocol mechanism is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers. A decisive acceptance test would be: The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This is a valid solution to a different Junos situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It does not directly correct the specific failure evidence here: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The required targeted change is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. This is a valid solution to a different Junos situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It does not directly correct the specific failure evidence here: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The required targeted change is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
Restore a supported IGMP querier path or appropriately configured snooping querier function. This is a valid solution to a different Junos situation: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. It does not directly correct the specific failure evidence here: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The required targeted change is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The proposed correction is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. Which observation MOST directly confirms this fault is resolved?
The group's receiver interface appears in IGMP membership and expected multicast forwarding state. This is the direct acceptance evidence for the observed failure: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The mechanism being validated is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. That would validate a different condition: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The decisive check for the current issue is: The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
Periodic membership queries and reports maintain the group's correct receiver-port entries. That would validate a different condition: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The decisive check for the current issue is: The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
A Junos engineer proposes this response: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. The situation is: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. Which technical principle BEST justifies the response?
IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers. This is the controlling mechanism in the specific case: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. It predicts the acceptance result: The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
PIM forwarding-state construction requires participating multicast routers along the path. This principle explains a separate situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. For this issue the relevant mechanism is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
IPv4 SSM requires source-specific membership information for the intended stream. This principle explains a separate situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. For this issue the relevant mechanism is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
IGMP queries refresh host group membership information used by snooping bridges. This principle explains a separate situation: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. For this issue the relevant mechanism is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. If the team bypasses or fails to implement the targeted correction (Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.), which direct operational risk or residual exposure is MOST relevant?
With no valid receiver membership, the router may not build the intended downstream multicast branch. This is the consequence linked to the observed situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. It is prevented by: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. The underlying reason is: IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. This risk belongs to a different operational problem: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The stated condition instead exposes this direct risk: With no valid receiver membership, the router may not build the intended downstream multicast branch. The appropriate mitigation is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
Group-only joins without mapping cannot unambiguously select a source for the SSM group. This risk belongs to a different operational problem: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The stated condition instead exposes this direct risk: With no valid receiver membership, the router may not build the intended downstream multicast branch. The appropriate mitigation is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
Absent queries may cause membership state to age out and receivers to stop getting traffic. This risk belongs to a different operational problem: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The stated condition instead exposes this direct risk: With no valid receiver membership, the router may not build the intended downstream multicast branch. The appropriate mitigation is: Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. Which targeted engineering change is MOST directly justified by the observed evidence?
Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. This change specifically addresses the reported evidence: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The relevant protocol mechanism is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM. A decisive acceptance test would be: The multicast state shows the exact (source,group) pair requested by the receiver.
Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. This is a valid solution to a different Junos situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It does not directly correct the specific failure evidence here: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The required targeted change is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers. This is a valid solution to a different Junos situation: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. It does not directly correct the specific failure evidence here: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The required targeted change is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This is a valid solution to a different Junos situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It does not directly correct the specific failure evidence here: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The required targeted change is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The proposed correction is: Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. Which observation MOST directly confirms this fault is resolved?
The multicast state shows the exact (source,group) pair requested by the receiver. This is the direct acceptance evidence for the observed failure: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The mechanism being validated is: IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM.
The multicast entry includes the named source and excludes other senders for the same group. That would validate a different condition: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. That would validate a different condition: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: The multicast state shows the exact (source,group) pair requested by the receiver.
Please check your mailbox for a message from support@examlabs.com and follow the directions.