Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 27

Question 260

A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. If the team bypasses or fails to implement the targeted correction (Inspect first-hop designated-router PIM register behavior and its policy toward the active RP.), which direct operational risk or residual exposure is MOST relevant?

  1. Inconsistent RP sets can split multicast source discovery and leave one receiver population isolated.
  2. Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth.
  3. Unfiltered multicast join or source advertisement may leak protected multicast traffic.
  4. Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources.

Explanation

Correct Answer

D:

Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources. This is the consequence linked to the observed situation: A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. It is prevented by: Inspect first-hop designated-router PIM register behavior and its policy toward the active RP. The underlying reason is: PIM-SM first-hop routers use register mechanisms to introduce ASM sources to the RP.

Incorrect Answers

A:

Inconsistent RP sets can split multicast source discovery and leave one receiver population isolated. This risk belongs to a different operational problem: Two PIM routers disagree on the RP learned through bootstrap-router discovery after a BSR domain partition. The stated condition instead exposes this direct risk: Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources. The appropriate mitigation is: Inspect first-hop designated-router PIM register behavior and its policy toward the active RP.

B:

Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. This risk belongs to a different operational problem: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The stated condition instead exposes this direct risk: Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources. The appropriate mitigation is: Inspect first-hop designated-router PIM register behavior and its policy toward the active RP.

C:

Unfiltered multicast join or source advertisement may leak protected multicast traffic. This risk belongs to a different operational problem: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The stated condition instead exposes this direct risk: Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources. The appropriate mitigation is: Inspect first-hop designated-router PIM register behavior and its policy toward the active RP.

Question 261

A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain.
  2. Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.
  3. Inspect first-hop designated-router PIM register behavior and its policy toward the active RP.
  4. Restore a supported IGMP querier path or appropriately configured snooping querier function.

Explanation

Correct Answer

B:

Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers. This change specifically addresses the reported evidence: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The relevant protocol mechanism is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree. A decisive acceptance test would be: Source traffic follows the intended shortest-path tree without unnecessary RP transit.

Incorrect Answers

A:

Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. This is a valid solution to a different Junos situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. It does not directly correct the specific failure evidence here: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The required targeted change is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

C:

Inspect first-hop designated-router PIM register behavior and its policy toward the active RP. This is a valid solution to a different Junos situation: A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. It does not directly correct the specific failure evidence here: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The required targeted change is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

D:

Restore a supported IGMP querier path or appropriately configured snooping querier function. This is a valid solution to a different Junos situation: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. It does not directly correct the specific failure evidence here: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The required targeted change is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

Question 262

A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The proposed correction is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers. Which observation MOST directly confirms this fault is resolved?

  1. The last-hop router discovers the RP and joins the (*,G) shared distribution tree.
  2. The RP receives expected source registration and interested receiver trees start forwarding data.
  3. Source traffic follows the intended shortest-path tree without unnecessary RP transit.
  4. Periodic membership queries and reports maintain the group's correct receiver-port entries.

Explanation

Correct Answer

C:

Source traffic follows the intended shortest-path tree without unnecessary RP transit. This is the direct acceptance evidence for the observed failure: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The mechanism being validated is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

Incorrect Answers

A:

The last-hop router discovers the RP and joins the (*,G) shared distribution tree. That would validate a different condition: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The decisive check for the current issue is: Source traffic follows the intended shortest-path tree without unnecessary RP transit.

B:

The RP receives expected source registration and interested receiver trees start forwarding data. That would validate a different condition: A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. The decisive check for the current issue is: Source traffic follows the intended shortest-path tree without unnecessary RP transit.

D:

Periodic membership queries and reports maintain the group's correct receiver-port entries. That would validate a different condition: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The decisive check for the current issue is: Source traffic follows the intended shortest-path tree without unnecessary RP transit.

Question 263

A Junos engineer proposes this response: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers. The situation is: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. Which technical principle BEST justifies the response?

  1. PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM.
  2. PIM-SM first-hop routers use register mechanisms to introduce ASM sources to the RP.
  3. IGMP queries refresh host group membership information used by snooping bridges.
  4. PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

Explanation

Correct Answer

D:

PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree. This is the controlling mechanism in the specific case: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. It predicts the acceptance result: Source traffic follows the intended shortest-path tree without unnecessary RP transit.

Incorrect Answers

A:

PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM. This principle explains a separate situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. For this issue the relevant mechanism is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

B:

PIM-SM first-hop routers use register mechanisms to introduce ASM sources to the RP. This principle explains a separate situation: A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. For this issue the relevant mechanism is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

C:

IGMP queries refresh host group membership information used by snooping bridges. This principle explains a separate situation: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. For this issue the relevant mechanism is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

Question 264

A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. If the team bypasses or fails to implement the targeted correction (Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.), which direct operational risk or residual exposure is MOST relevant?

  1. Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth.
  2. Without an RP for the ASM group, the normal shared tree cannot be established.
  3. Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources.
  4. Absent queries may cause membership state to age out and receivers to stop getting traffic.

Explanation

Correct Answer

A:

Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. This is the consequence linked to the observed situation: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. It is prevented by: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers. The underlying reason is: PIM-SM receivers may transition from an RP shared tree to a source-specific shortest-path tree.

Incorrect Answers

B:

Without an RP for the ASM group, the normal shared tree cannot be established. This risk belongs to a different operational problem: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The stated condition instead exposes this direct risk: Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. The appropriate mitigation is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

C:

Blocking legitimate PIM register messages can keep distant ASM receivers unaware of new sources. This risk belongs to a different operational problem: A source begins sending to an ASM group but the first-hop PIM router never registers the source with the mapped RP. The stated condition instead exposes this direct risk: Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. The appropriate mitigation is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

D:

Absent queries may cause membership state to age out and receivers to stop getting traffic. This risk belongs to a different operational problem: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The stated condition instead exposes this direct risk: Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. The appropriate mitigation is: Check the supported shortest-path-tree switchover and (S,G) state for interested last-hop routers.

Question 265

An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Verify snooping multicast-router interfaces and their link to the intended PIM router.
  2. Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.
  3. Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.
  4. Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.

Explanation

Correct Answer

C:

Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This change specifically addresses the reported evidence: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The relevant protocol mechanism is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding. A decisive acceptance test would be: Only interested receiver ports and required multicast-router ports forward the group traffic.

Incorrect Answers

A:

Verify snooping multicast-router interfaces and their link to the intended PIM router. This is a valid solution to a different Junos situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. It does not directly correct the specific failure evidence here: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The required targeted change is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

B:

Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This is a valid solution to a different Junos situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It does not directly correct the specific failure evidence here: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The required targeted change is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

D:

Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. This is a valid solution to a different Junos situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It does not directly correct the specific failure evidence here: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The required targeted change is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

Question 266

An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The proposed correction is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. Which observation MOST directly confirms this fault is resolved?

  1. Membership reports reach the multicast router while group data uses the right downstream ports.
  2. The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
  3. The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
  4. Only interested receiver ports and required multicast-router ports forward the group traffic.

Explanation

Correct Answer

D:

Only interested receiver ports and required multicast-router ports forward the group traffic. This is the direct acceptance evidence for the observed failure: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The mechanism being validated is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.

Incorrect Answers

A:

Membership reports reach the multicast router while group data uses the right downstream ports. That would validate a different condition: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The decisive check for the current issue is: Only interested receiver ports and required multicast-router ports forward the group traffic.

B:

The group's receiver interface appears in IGMP membership and expected multicast forwarding state. That would validate a different condition: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The decisive check for the current issue is: Only interested receiver ports and required multicast-router ports forward the group traffic.

C:

The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. That would validate a different condition: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The decisive check for the current issue is: Only interested receiver ports and required multicast-router ports forward the group traffic.

Question 267

A Junos engineer proposes this response: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. The situation is: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. Which technical principle BEST justifies the response?

  1. IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.
  2. Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
  3. PIM forwarding-state construction requires participating multicast routers along the path.
  4. IPv4 SSM requires source-specific membership information for the intended stream.

Explanation

Correct Answer

A:

IGMP snooping observes membership reports to constrain Layer 2 multicast flooding. This is the controlling mechanism in the specific case: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It predicts the acceptance result: Only interested receiver ports and required multicast-router ports forward the group traffic.

Incorrect Answers

B:

Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports. This principle explains a separate situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. For this issue the relevant mechanism is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.

C:

PIM forwarding-state construction requires participating multicast routers along the path. This principle explains a separate situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. For this issue the relevant mechanism is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.

D:

IPv4 SSM requires source-specific membership information for the intended stream. This principle explains a separate situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. For this issue the relevant mechanism is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.

Question 268

An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. If the team bypasses or fails to implement the targeted correction (Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.), which direct operational risk or residual exposure is MOST relevant?

  1. Incorrect router-port discovery can isolate group membership messages from the PIM control plane.
  2. Without correct snooping state, multicast can consume bandwidth on uninterested host ports.
  3. With no valid receiver membership, the router may not build the intended downstream multicast branch.
  4. Group-only joins without mapping cannot unambiguously select a source for the SSM group.

Explanation

Correct Answer

B:

Without correct snooping state, multicast can consume bandwidth on uninterested host ports. This is the consequence linked to the observed situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It is prevented by: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. The underlying reason is: IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.

Incorrect Answers

A:

Incorrect router-port discovery can isolate group membership messages from the PIM control plane. This risk belongs to a different operational problem: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The stated condition instead exposes this direct risk: Without correct snooping state, multicast can consume bandwidth on uninterested host ports. The appropriate mitigation is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

C:

With no valid receiver membership, the router may not build the intended downstream multicast branch. This risk belongs to a different operational problem: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The stated condition instead exposes this direct risk: Without correct snooping state, multicast can consume bandwidth on uninterested host ports. The appropriate mitigation is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

D:

Group-only joins without mapping cannot unambiguously select a source for the SSM group. This risk belongs to a different operational problem: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The stated condition instead exposes this direct risk: Without correct snooping state, multicast can consume bandwidth on uninterested host ports. The appropriate mitigation is: Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.

Question 269

IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.
  2. Restore the correct RPF unicast reachability to the RP before changing receiver-side IGMP settings.
  3. Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.
  4. Restore a supported IGMP querier path or appropriately configured snooping querier function.

Explanation

Correct Answer

D:

Restore a supported IGMP querier path or appropriately configured snooping querier function. This change specifically addresses the reported evidence: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The relevant protocol mechanism is: IGMP queries refresh host group membership information used by snooping bridges. A decisive acceptance test would be: Periodic membership queries and reports maintain the group's correct receiver-port entries.

Incorrect Answers

A:

Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This is a valid solution to a different Junos situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It does not directly correct the specific failure evidence here: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The required targeted change is: Restore a supported IGMP querier path or appropriately configured snooping querier function.

B:

Restore the correct RPF unicast reachability to the RP before changing receiver-side IGMP settings. This is a valid solution to a different Junos situation: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. It does not directly correct the specific failure evidence here: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The required targeted change is: Restore a supported IGMP querier path or appropriately configured snooping querier function.

C:

Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. This is a valid solution to a different Junos situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. It does not directly correct the specific failure evidence here: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The required targeted change is: Restore a supported IGMP querier path or appropriately configured snooping querier function.

Question 270

IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The proposed correction is: Restore a supported IGMP querier path or appropriately configured snooping querier function. Which observation MOST directly confirms this fault is resolved?

  1. Periodic membership queries and reports maintain the group's correct receiver-port entries.
  2. Only interested receiver ports and required multicast-router ports forward the group traffic.
  3. The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP.
  4. The multicast state shows the exact (source,group) pair requested by the receiver.

Explanation

Correct Answer

A:

Periodic membership queries and reports maintain the group's correct receiver-port entries. This is the direct acceptance evidence for the observed failure: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The mechanism being validated is: IGMP queries refresh host group membership information used by snooping bridges.

Incorrect Answers

B:

Only interested receiver ports and required multicast-router ports forward the group traffic. That would validate a different condition: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.

C:

The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP. That would validate a different condition: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.

D:

The multicast state shows the exact (source,group) pair requested by the receiver. That would validate a different condition: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports