JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The proposed correction is: Restore a supported IGMP querier path or appropriately configured snooping querier function. Which observation MOST directly confirms this fault is resolved?
Periodic membership queries and reports maintain the group's correct receiver-port entries. This is the direct acceptance evidence for the observed failure: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. The mechanism being validated is: IGMP queries refresh host group membership information used by snooping bridges.
Only interested receiver ports and required multicast-router ports forward the group traffic. That would validate a different condition: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.
The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP. That would validate a different condition: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.
The multicast state shows the exact (source,group) pair requested by the receiver. That would validate a different condition: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The decisive check for the current issue is: Periodic membership queries and reports maintain the group's correct receiver-port entries.
A Junos engineer proposes this response: Restore a supported IGMP querier path or appropriately configured snooping querier function. The situation is: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. Which technical principle BEST justifies the response?
IGMP queries refresh host group membership information used by snooping bridges. This is the controlling mechanism in the specific case: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. It predicts the acceptance result: Periodic membership queries and reports maintain the group's correct receiver-port entries.
Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports. This principle explains a separate situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. For this issue the relevant mechanism is: IGMP queries refresh host group membership information used by snooping bridges.
IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers. This principle explains a separate situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. For this issue the relevant mechanism is: IGMP queries refresh host group membership information used by snooping bridges.
IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM. This principle explains a separate situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. For this issue the relevant mechanism is: IGMP queries refresh host group membership information used by snooping bridges.
IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. If the team bypasses or fails to implement the targeted correction (Restore a supported IGMP querier path or appropriately configured snooping querier function.), which direct operational risk or residual exposure is MOST relevant?
Absent queries may cause membership state to age out and receivers to stop getting traffic. This is the consequence linked to the observed situation: IGMP snooping shows no members after the Layer 3 querier was removed from a shared VLAN and membership reports aged out. It is prevented by: Restore a supported IGMP querier path or appropriately configured snooping querier function. The underlying reason is: IGMP queries refresh host group membership information used by snooping bridges.
Without correct snooping state, multicast can consume bandwidth on uninterested host ports. This risk belongs to a different operational problem: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The stated condition instead exposes this direct risk: Absent queries may cause membership state to age out and receivers to stop getting traffic. The appropriate mitigation is: Restore a supported IGMP querier path or appropriately configured snooping querier function.
A healthy IGMP membership cannot compensate for missing RPF connectivity to the RP. This risk belongs to a different operational problem: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The stated condition instead exposes this direct risk: Absent queries may cause membership state to age out and receivers to stop getting traffic. The appropriate mitigation is: Restore a supported IGMP querier path or appropriately configured snooping querier function.
Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. This risk belongs to a different operational problem: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The stated condition instead exposes this direct risk: Absent queries may cause membership state to age out and receivers to stop getting traffic. The appropriate mitigation is: Restore a supported IGMP querier path or appropriately configured snooping querier function.
A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. Which targeted engineering change is MOST directly justified by the observed evidence?
Verify snooping multicast-router interfaces and their link to the intended PIM router. This change specifically addresses the reported evidence: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The relevant protocol mechanism is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports. A decisive acceptance test would be: Membership reports reach the multicast router while group data uses the right downstream ports.
Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This is a valid solution to a different Junos situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It does not directly correct the specific failure evidence here: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The required targeted change is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
Restore the correct RPF unicast reachability to the RP before changing receiver-side IGMP settings. This is a valid solution to a different Junos situation: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. It does not directly correct the specific failure evidence here: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The required targeted change is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
Configure and verify the necessary MSDP source-active exchange between the intended RPs. This is a valid solution to a different Junos situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. It does not directly correct the specific failure evidence here: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The required targeted change is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The proposed correction is: Verify snooping multicast-router interfaces and their link to the intended PIM router. Which observation MOST directly confirms this fault is resolved?
Membership reports reach the multicast router while group data uses the right downstream ports. This is the direct acceptance evidence for the observed failure: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The mechanism being validated is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
Only interested receiver ports and required multicast-router ports forward the group traffic. That would validate a different condition: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The decisive check for the current issue is: Membership reports reach the multicast router while group data uses the right downstream ports.
The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP. That would validate a different condition: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The decisive check for the current issue is: Membership reports reach the multicast router while group data uses the right downstream ports.
Each RP learns the relevant remote active-source advertisements and receivers can join their sources. That would validate a different condition: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The decisive check for the current issue is: Membership reports reach the multicast router while group data uses the right downstream ports.
A Junos engineer proposes this response: Verify snooping multicast-router interfaces and their link to the intended PIM router. The situation is: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. Which technical principle BEST justifies the response?
Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports. This is the controlling mechanism in the specific case: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. It predicts the acceptance result: Membership reports reach the multicast router while group data uses the right downstream ports.
IGMP snooping observes membership reports to constrain Layer 2 multicast flooding. This principle explains a separate situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. For this issue the relevant mechanism is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
PIM chooses an upstream interface using reverse-path forwarding lookups. This principle explains a separate situation: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. For this issue the relevant mechanism is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
MSDP can convey active-source information across separate RP domains or Anycast RP peers. This principle explains a separate situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. For this issue the relevant mechanism is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. If the team bypasses or fails to implement the targeted correction (Verify snooping multicast-router interfaces and their link to the intended PIM router.), which direct operational risk or residual exposure is MOST relevant?
Incorrect router-port discovery can isolate group membership messages from the PIM control plane. This is the consequence linked to the observed situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. It is prevented by: Verify snooping multicast-router interfaces and their link to the intended PIM router. The underlying reason is: Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.
Without correct snooping state, multicast can consume bandwidth on uninterested host ports. This risk belongs to a different operational problem: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The stated condition instead exposes this direct risk: Incorrect router-port discovery can isolate group membership messages from the PIM control plane. The appropriate mitigation is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
A healthy IGMP membership cannot compensate for missing RPF connectivity to the RP. This risk belongs to a different operational problem: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The stated condition instead exposes this direct risk: Incorrect router-port discovery can isolate group membership messages from the PIM control plane. The appropriate mitigation is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
An Anycast address alone does not synchronize active-source discovery in an MSDP-based design. This risk belongs to a different operational problem: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The stated condition instead exposes this direct risk: Incorrect router-port discovery can isolate group membership messages from the PIM control plane. The appropriate mitigation is: Verify snooping multicast-router interfaces and their link to the intended PIM router.
A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. Which targeted engineering change is MOST directly justified by the observed evidence?
Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. This change specifically addresses the reported evidence: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The relevant protocol mechanism is: IPv4 SSM requires source-specific membership information for the intended stream. A decisive acceptance test would be: The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
Build a valid source-specific multicast tree using IGMPv3 source membership and PIM SSM, without requiring an RP. This is a valid solution to a different Junos situation: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. It does not directly correct the specific failure evidence here: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The required targeted change is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. This is a valid solution to a different Junos situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. It does not directly correct the specific failure evidence here: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The required targeted change is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
Configure and verify the necessary MSDP source-active exchange between the intended RPs. This is a valid solution to a different Junos situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. It does not directly correct the specific failure evidence here: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The required targeted change is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The proposed correction is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. Which observation MOST directly confirms this fault is resolved?
The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery. This is the direct acceptance evidence for the observed failure: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. The mechanism being validated is: IPv4 SSM requires source-specific membership information for the intended stream.
The requested (S,G) stream reaches subscribers directly along its source tree. That would validate a different condition: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The decisive check for the current issue is: The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
The multicast state shows the exact (source,group) pair requested by the receiver. That would validate a different condition: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The decisive check for the current issue is: The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
Each RP learns the relevant remote active-source advertisements and receivers can join their sources. That would validate a different condition: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The decisive check for the current issue is: The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
A Junos engineer proposes this response: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. The situation is: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. Which technical principle BEST justifies the response?
IPv4 SSM requires source-specific membership information for the intended stream. This is the controlling mechanism in the specific case: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It predicts the acceptance result: The last-hop router builds the intended (S,G) join rather than relying on group-only ASM discovery.
PIM SSM joins known sources and does not require RP discovery or an ASM shared tree. This principle explains a separate situation: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. For this issue the relevant mechanism is: IPv4 SSM requires source-specific membership information for the intended stream.
IGMPv3 source filtering allows receivers to specify an (S,G) interest for SSM. This principle explains a separate situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. For this issue the relevant mechanism is: IPv4 SSM requires source-specific membership information for the intended stream.
MSDP can convey active-source information across separate RP domains or Anycast RP peers. This principle explains a separate situation: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. For this issue the relevant mechanism is: IPv4 SSM requires source-specific membership information for the intended stream.
A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. If the team bypasses or fails to implement the targeted correction (Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.), which direct operational risk or residual exposure is MOST relevant?
Group-only joins without mapping cannot unambiguously select a source for the SSM group. This is the consequence linked to the observed situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It is prevented by: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. The underlying reason is: IPv4 SSM requires source-specific membership information for the intended stream.
Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. This risk belongs to a different operational problem: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. This risk belongs to a different operational problem: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
An Anycast address alone does not synchronize active-source discovery in an MSDP-based design. This risk belongs to a different operational problem: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.
Please check your mailbox for a message from support@examlabs.com and follow the directions.