Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 29

Question 280

A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. If the team bypasses or fails to implement the targeted correction (Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.), which direct operational risk or residual exposure is MOST relevant?

  1. Group-only joins without mapping cannot unambiguously select a source for the SSM group.
  2. Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state.
  3. Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic.
  4. An Anycast address alone does not synchronize active-source discovery in an MSDP-based design.

Explanation

Correct Answer

A:

Group-only joins without mapping cannot unambiguously select a source for the SSM group. This is the consequence linked to the observed situation: A network receives an IPv4 SSM group in the 232.0.0.0/8 range but client software only sends IGMPv2 group-only membership. It is prevented by: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address. The underlying reason is: IPv4 SSM requires source-specific membership information for the intended stream.

Incorrect Answers

B:

Depending on ASM RP advertisements for an SSM group introduces unnecessary and incorrect state. This risk belongs to a different operational problem: An SSM-only multicast video service was given an RP address although every subscriber explicitly knows the source address. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.

C:

Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. This risk belongs to a different operational problem: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.

D:

An Anycast address alone does not synchronize active-source discovery in an MSDP-based design. This risk belongs to a different operational problem: Two Anycast RP routers learn sources locally but receivers attached to the other RP miss those sources in a design that depends on MSDP. The stated condition instead exposes this direct risk: Group-only joins without mapping cannot unambiguously select a source for the SSM group. The appropriate mitigation is: Use an IGMPv3-capable receiver or a supported SSM mapping design that supplies the missing source address.

Question 281

Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Enable and examine the appropriate IGMP receiver-facing interface and group membership processing.
  2. Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
  3. Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.
  4. Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

Explanation

Correct Answer

C:

Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This change specifically addresses the reported evidence: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The relevant protocol mechanism is: PIM forwarding-state construction requires participating multicast routers along the path. A decisive acceptance test would be: Neighbor and join output shows PIM active on all links on the selected multicast path.

Incorrect Answers

A:

Enable and examine the appropriate IGMP receiver-facing interface and group membership processing. This is a valid solution to a different Junos situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. It does not directly correct the specific failure evidence here: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The required targeted change is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

B:

Permit PIM control signaling and expected multicast traffic on the specific authorized transit path. This is a valid solution to a different Junos situation: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. It does not directly correct the specific failure evidence here: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The required targeted change is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

D:

Apply the appropriate multicast routing policy or group scoping at the PIM boundary. This is a valid solution to a different Junos situation: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. It does not directly correct the specific failure evidence here: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The required targeted change is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

Question 282

Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The proposed correction is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. Which observation MOST directly confirms this fault is resolved?

  1. The group's receiver interface appears in IGMP membership and expected multicast forwarding state.
  2. Neighbors and join output converge and group data reaches the interested receiver interfaces.
  3. The restricted group is absent from external join and forwarding state while approved groups still work.
  4. Neighbor and join output shows PIM active on all links on the selected multicast path.

Explanation

Correct Answer

D:

Neighbor and join output shows PIM active on all links on the selected multicast path. This is the direct acceptance evidence for the observed failure: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The mechanism being validated is: PIM forwarding-state construction requires participating multicast routers along the path.

Incorrect Answers

A:

The group's receiver interface appears in IGMP membership and expected multicast forwarding state. That would validate a different condition: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The decisive check for the current issue is: Neighbor and join output shows PIM active on all links on the selected multicast path.

B:

Neighbors and join output converge and group data reaches the interested receiver interfaces. That would validate a different condition: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The decisive check for the current issue is: Neighbor and join output shows PIM active on all links on the selected multicast path.

C:

The restricted group is absent from external join and forwarding state while approved groups still work. That would validate a different condition: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The decisive check for the current issue is: Neighbor and join output shows PIM active on all links on the selected multicast path.

Question 283

A Junos engineer proposes this response: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. The situation is: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. Which technical principle BEST justifies the response?

  1. PIM forwarding-state construction requires participating multicast routers along the path.
  2. IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers.
  3. Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
  4. Multicast policies can constrain which source and group information crosses a boundary.

Explanation

Correct Answer

A:

PIM forwarding-state construction requires participating multicast routers along the path. This is the controlling mechanism in the specific case: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It predicts the acceptance result: Neighbor and join output shows PIM active on all links on the selected multicast path.

Incorrect Answers

B:

IGMP lets hosts indicate interest in IPv4 multicast groups to adjacent multicast routers. This principle explains a separate situation: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. For this issue the relevant mechanism is: PIM forwarding-state construction requires participating multicast routers along the path.

C:

Multicast control uses PIM joins across intermediate routers independently of local host IGMP. This principle explains a separate situation: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. For this issue the relevant mechanism is: PIM forwarding-state construction requires participating multicast routers along the path.

D:

Multicast policies can constrain which source and group information crosses a boundary. This principle explains a separate situation: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. For this issue the relevant mechanism is: PIM forwarding-state construction requires participating multicast routers along the path.

Question 284

Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. If the team bypasses or fails to implement the targeted correction (Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.), which direct operational risk or residual exposure is MOST relevant?

  1. With no valid receiver membership, the router may not build the intended downstream multicast branch.
  2. Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree.
  3. Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built.
  4. Unfiltered multicast join or source advertisement may leak protected multicast traffic.

Explanation

Correct Answer

B:

Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. This is the consequence linked to the observed situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It is prevented by: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. The underlying reason is: PIM forwarding-state construction requires participating multicast routers along the path.

Incorrect Answers

A:

With no valid receiver membership, the router may not build the intended downstream multicast branch. This risk belongs to a different operational problem: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The stated condition instead exposes this direct risk: Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. The appropriate mitigation is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

C:

Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built. This risk belongs to a different operational problem: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The stated condition instead exposes this direct risk: Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. The appropriate mitigation is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

D:

Unfiltered multicast join or source advertisement may leak protected multicast traffic. This risk belongs to a different operational problem: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The stated condition instead exposes this direct risk: Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. The appropriate mitigation is: Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.

Question 285

An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Deploy supported Anycast RP peers with matching anycast address and appropriate source-discovery method.
  2. Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships.
  3. Verify snooping multicast-router interfaces and their link to the intended PIM router.
  4. Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

Explanation

Correct Answer

D:

Apply the appropriate multicast routing policy or group scoping at the PIM boundary. This change specifically addresses the reported evidence: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The relevant protocol mechanism is: Multicast policies can constrain which source and group information crosses a boundary. A decisive acceptance test would be: The restricted group is absent from external join and forwarding state while approved groups still work.

Incorrect Answers

A:

Deploy supported Anycast RP peers with matching anycast address and appropriate source-discovery method. This is a valid solution to a different Junos situation: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. It does not directly correct the specific failure evidence here: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The required targeted change is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

B:

Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This is a valid solution to a different Junos situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It does not directly correct the specific failure evidence here: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The required targeted change is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

C:

Verify snooping multicast-router interfaces and their link to the intended PIM router. This is a valid solution to a different Junos situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. It does not directly correct the specific failure evidence here: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The required targeted change is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

Question 286

An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The proposed correction is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary. Which observation MOST directly confirms this fault is resolved?

  1. The restricted group is absent from external join and forwarding state while approved groups still work.
  2. An RP outage causes the PIM routers to resolve and use a surviving anycast RP as designed.
  3. Only interested receiver ports and required multicast-router ports forward the group traffic.
  4. Membership reports reach the multicast router while group data uses the right downstream ports.

Explanation

Correct Answer

A:

The restricted group is absent from external join and forwarding state while approved groups still work. This is the direct acceptance evidence for the observed failure: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. The mechanism being validated is: Multicast policies can constrain which source and group information crosses a boundary.

Incorrect Answers

B:

An RP outage causes the PIM routers to resolve and use a surviving anycast RP as designed. That would validate a different condition: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. The decisive check for the current issue is: The restricted group is absent from external join and forwarding state while approved groups still work.

C:

Only interested receiver ports and required multicast-router ports forward the group traffic. That would validate a different condition: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The decisive check for the current issue is: The restricted group is absent from external join and forwarding state while approved groups still work.

D:

Membership reports reach the multicast router while group data uses the right downstream ports. That would validate a different condition: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The decisive check for the current issue is: The restricted group is absent from external join and forwarding state while approved groups still work.

Question 287

A Junos engineer proposes this response: Apply the appropriate multicast routing policy or group scoping at the PIM boundary. The situation is: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. Which technical principle BEST justifies the response?

  1. Anycast RP provides redundant shared-tree rendezvous service using multiple RP nodes.
  2. Multicast policies can constrain which source and group information crosses a boundary.
  3. IGMP snooping observes membership reports to constrain Layer 2 multicast flooding.
  4. Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports.

Explanation

Correct Answer

B:

Multicast policies can constrain which source and group information crosses a boundary. This is the controlling mechanism in the specific case: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. It predicts the acceptance result: The restricted group is absent from external join and forwarding state while approved groups still work.

Incorrect Answers

A:

Anycast RP provides redundant shared-tree rendezvous service using multiple RP nodes. This principle explains a separate situation: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. For this issue the relevant mechanism is: Multicast policies can constrain which source and group information crosses a boundary.

C:

IGMP snooping observes membership reports to constrain Layer 2 multicast flooding. This principle explains a separate situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. For this issue the relevant mechanism is: Multicast policies can constrain which source and group information crosses a boundary.

D:

Snooping forwarding distinguishes receiver membership ports from multicast-router-facing ports. This principle explains a separate situation: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. For this issue the relevant mechanism is: Multicast policies can constrain which source and group information crosses a boundary.

Question 288

An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. If the team bypasses or fails to implement the targeted correction (Apply the appropriate multicast routing policy or group scoping at the PIM boundary.), which direct operational risk or residual exposure is MOST relevant?

  1. A single physical RP remains a service failure point for ASM multicast groups.
  2. Without correct snooping state, multicast can consume bandwidth on uninterested host ports.
  3. Unfiltered multicast join or source advertisement may leak protected multicast traffic.
  4. Incorrect router-port discovery can isolate group membership messages from the PIM control plane.

Explanation

Correct Answer

C:

Unfiltered multicast join or source advertisement may leak protected multicast traffic. This is the consequence linked to the observed situation: An enterprise wants to prevent multicast traffic for an internal group from being carried toward an external partner edge. It is prevented by: Apply the appropriate multicast routing policy or group scoping at the PIM boundary. The underlying reason is: Multicast policies can constrain which source and group information crosses a boundary.

Incorrect Answers

A:

A single physical RP remains a service failure point for ASM multicast groups. This risk belongs to a different operational problem: An enterprise wants PIM sparse-mode redundancy after the only Rendezvous Point router repeatedly loses power. The stated condition instead exposes this direct risk: Unfiltered multicast join or source advertisement may leak protected multicast traffic. The appropriate mitigation is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

B:

Without correct snooping state, multicast can consume bandwidth on uninterested host ports. This risk belongs to a different operational problem: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The stated condition instead exposes this direct risk: Unfiltered multicast join or source advertisement may leak protected multicast traffic. The appropriate mitigation is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

D:

Incorrect router-port discovery can isolate group membership messages from the PIM control plane. This risk belongs to a different operational problem: A multicast access VLAN has working IGMP memberships but lacks an identified upstream router port for forwarding reports toward the core. The stated condition instead exposes this direct risk: Unfiltered multicast join or source advertisement may leak protected multicast traffic. The appropriate mitigation is: Apply the appropriate multicast routing policy or group scoping at the PIM boundary.

Question 289

A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Re-evaluate PIM RPF entries and unicast reachability after the routing convergence.
  2. Correct the routing or RPF table entry so the multicast flow arrives on the expected upstream interface.
  3. Enable the supported PIM interface on every transit hop needed by the multicast distribution tree.
  4. Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree.

Explanation

Correct Answer

A:

Re-evaluate PIM RPF entries and unicast reachability after the routing convergence. This change specifically addresses the reported evidence: A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The relevant protocol mechanism is: PIM relies on unicast or explicit multicast RPF routing information that can change during failover. A decisive acceptance test would be: The multicast incoming interface matches the new RPF path and data forwarding resumes.

Incorrect Answers

B:

Correct the routing or RPF table entry so the multicast flow arrives on the expected upstream interface. This is a valid solution to a different Junos situation: Multicast packets from a source enter a router on an interface different from the RPF interface calculated toward the source. It does not directly correct the specific failure evidence here: A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The required targeted change is: Re-evaluate PIM RPF entries and unicast reachability after the routing convergence.

C:

Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This is a valid solution to a different Junos situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It does not directly correct the specific failure evidence here: A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The required targeted change is: Re-evaluate PIM RPF entries and unicast reachability after the routing convergence.

D:

Verify IGMPv3 INCLUDE source-list membership and the matching PIM source-specific tree. This is a valid solution to a different Junos situation: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. It does not directly correct the specific failure evidence here: A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The required targeted change is: Re-evaluate PIM RPF entries and unicast reachability after the routing convergence.

Question 290

A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The proposed correction is: Re-evaluate PIM RPF entries and unicast reachability after the routing convergence. Which observation MOST directly confirms this fault is resolved?

  1. The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP.
  2. The multicast incoming interface matches the new RPF path and data forwarding resumes.
  3. Neighbor and join output shows PIM active on all links on the selected multicast path.
  4. The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.

Explanation

Correct Answer

B:

The multicast incoming interface matches the new RPF path and data forwarding resumes. This is the direct acceptance evidence for the observed failure: A multicast receiver stops after a WAN failover because the new unicast best path to the source uses another interface. The mechanism being validated is: PIM relies on unicast or explicit multicast RPF routing information that can change during failover.

Incorrect Answers

A:

The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP. That would validate a different condition: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The decisive check for the current issue is: The multicast incoming interface matches the new RPF path and data forwarding resumes.

C:

Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: The multicast incoming interface matches the new RPF path and data forwarding resumes.

D:

The PIM join distribution and forwarding counters reflect the intended balanced upstream selection. That would validate a different condition: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The decisive check for the current issue is: The multicast incoming interface matches the new RPF path and data forwarding resumes.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports