JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. If the team bypasses or fails to implement the targeted correction (Change the receiver membership to an INCLUDE list for the specified SSM source.), which direct operational risk or residual exposure is MOST relevant?
An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. This is the consequence linked to the observed situation: An IGMPv3 receiver joins a group with an EXCLUDE list while a new design requires an explicit single allowed source. It is prevented by: Change the receiver membership to an INCLUDE list for the specified SSM source. The underlying reason is: IGMPv3 INCLUDE lists express positive source membership for source-specific reception.
Ignoring source filtering can admit unwanted sources or misdiagnose missing SSM traffic. This risk belongs to a different operational problem: An IGMPv3 receiver requests traffic only from source 198.51.100.9 for group 232.10.1.1, yet the operator checks only group-wide (*,G) state. The stated condition instead exposes this direct risk: An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. The appropriate mitigation is: Change the receiver membership to an INCLUDE list for the specified SSM source.
With no valid receiver membership, the router may not build the intended downstream multicast branch. This risk belongs to a different operational problem: An IPTV receiver joins an IPv4 ASM group but the attached Junos router has no current IGMP membership state for the interface. The stated condition instead exposes this direct risk: An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. The appropriate mitigation is: Change the receiver membership to an INCLUDE list for the specified SSM source.
Remaining on an unsuitable RP-centered path can increase multicast transit latency and bandwidth. This risk belongs to a different operational problem: A sparse-mode group reaches receivers through an inefficient path via the RP after the source becomes known. The stated condition instead exposes this direct risk: An EXCLUDE-style group request may admit unintended source traffic in the wrong service design. The appropriate mitigation is: Change the receiver membership to an INCLUDE list for the specified SSM source.
A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. Which targeted engineering change is MOST directly justified by the observed evidence?
Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability. This change specifically addresses the reported evidence: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The relevant protocol mechanism is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths. A decisive acceptance test would be: The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.
Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. This is a valid solution to a different Junos situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. It does not directly correct the specific failure evidence here: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The required targeted change is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This is a valid solution to a different Junos situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It does not directly correct the specific failure evidence here: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The required targeted change is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
Enable supported IGMP snooping on the affected VLAN and verify learned group port memberships. This is a valid solution to a different Junos situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. It does not directly correct the specific failure evidence here: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The required targeted change is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The proposed correction is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability. Which observation MOST directly confirms this fault is resolved?
The PIM join distribution and forwarding counters reflect the intended balanced upstream selection. This is the direct acceptance evidence for the observed failure: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. The mechanism being validated is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths.
The last-hop router discovers the RP and joins the (*,G) shared distribution tree. That would validate a different condition: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The decisive check for the current issue is: The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.
Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.
Only interested receiver ports and required multicast-router ports forward the group traffic. That would validate a different condition: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The decisive check for the current issue is: The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.
A Junos engineer proposes this response: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability. The situation is: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. Which technical principle BEST justifies the response?
PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths. This is the controlling mechanism in the specific case: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. It predicts the acceptance result: The PIM join distribution and forwarding counters reflect the intended balanced upstream selection.
PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM. This principle explains a separate situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. For this issue the relevant mechanism is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths.
PIM forwarding-state construction requires participating multicast routers along the path. This principle explains a separate situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. For this issue the relevant mechanism is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths.
IGMP snooping observes membership reports to constrain Layer 2 multicast flooding. This principle explains a separate situation: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. For this issue the relevant mechanism is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths.
A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. If the team bypasses or fails to implement the targeted correction (Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.), which direct operational risk or residual exposure is MOST relevant?
Assuming unicast ECMP alone balances every multicast tree may leave all group load on one link. This is the consequence linked to the observed situation: A campus routes one multicast group across two parallel links but all joins flow across a congested upstream even though equal-cost alternatives exist. It is prevented by: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability. The underlying reason is: PIM join load balancing can distribute group joins across qualifying equal-cost upstream paths.
Without an RP for the ASM group, the normal shared tree cannot be established. This risk belongs to a different operational problem: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The stated condition instead exposes this direct risk: Assuming unicast ECMP alone balances every multicast tree may leave all group load on one link. The appropriate mitigation is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. This risk belongs to a different operational problem: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The stated condition instead exposes this direct risk: Assuming unicast ECMP alone balances every multicast tree may leave all group load on one link. The appropriate mitigation is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
Without correct snooping state, multicast can consume bandwidth on uninterested host ports. This risk belongs to a different operational problem: An IGMP snooping access switch floods multicast video to every edge port although only two hosts joined the group. The stated condition instead exposes this direct risk: Assuming unicast ECMP alone balances every multicast tree may leave all group load on one link. The appropriate mitigation is: Review supported PIM join load-balancing behavior and equal-cost RPF candidate availability.
A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. Which targeted engineering change is MOST directly justified by the observed evidence?
Permit PIM control signaling and expected multicast traffic on the specific authorized transit path. This change specifically addresses the reported evidence: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The relevant protocol mechanism is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP. A decisive acceptance test would be: Neighbors and join output converge and group data reaches the interested receiver interfaces.
Restore the correct RPF unicast reachability to the RP before changing receiver-side IGMP settings. This is a valid solution to a different Junos situation: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. It does not directly correct the specific failure evidence here: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The required targeted change is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
Enable the supported PIM interface on every transit hop needed by the multicast distribution tree. This is a valid solution to a different Junos situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. It does not directly correct the specific failure evidence here: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The required targeted change is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
Configure a supported RP mapping for the intended ASM multicast groups across the PIM domain. This is a valid solution to a different Junos situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. It does not directly correct the specific failure evidence here: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The required targeted change is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The proposed correction is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path. Which observation MOST directly confirms this fault is resolved?
Neighbors and join output converge and group data reaches the interested receiver interfaces. This is the direct acceptance evidence for the observed failure: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. The mechanism being validated is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
The PIM (*,G) Join follows the RPF interface and shared tree state reaches the RP. That would validate a different condition: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The decisive check for the current issue is: Neighbors and join output converge and group data reaches the interested receiver interfaces.
Neighbor and join output shows PIM active on all links on the selected multicast path. That would validate a different condition: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The decisive check for the current issue is: Neighbors and join output converge and group data reaches the interested receiver interfaces.
The last-hop router discovers the RP and joins the (*,G) shared distribution tree. That would validate a different condition: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The decisive check for the current issue is: Neighbors and join output converge and group data reaches the interested receiver interfaces.
A Junos engineer proposes this response: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path. The situation is: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. Which technical principle BEST justifies the response?
Multicast control uses PIM joins across intermediate routers independently of local host IGMP. This is the controlling mechanism in the specific case: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. It predicts the acceptance result: Neighbors and join output converge and group data reaches the interested receiver interfaces.
PIM chooses an upstream interface using reverse-path forwarding lookups. This principle explains a separate situation: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. For this issue the relevant mechanism is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
PIM forwarding-state construction requires participating multicast routers along the path. This principle explains a separate situation: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. For this issue the relevant mechanism is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
PIM sparse mode uses a rendezvous point for shared-tree source discovery in ASM. This principle explains a separate situation: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. For this issue the relevant mechanism is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. If the team bypasses or fails to implement the targeted correction (Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.), which direct operational risk or residual exposure is MOST relevant?
Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built. This is the consequence linked to the observed situation: A firewall drops PIM join packets on an intermediate router while standard unicast traffic and IGMP receiver registration succeed. It is prevented by: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path. The underlying reason is: Multicast control uses PIM joins across intermediate routers independently of local host IGMP.
A healthy IGMP membership cannot compensate for missing RPF connectivity to the RP. This risk belongs to a different operational problem: A PIM sparse-mode router receives an IGMP join but the upstream link toward its configured RP is absent from the unicast routing table. The stated condition instead exposes this direct risk: Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built. The appropriate mitigation is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
Enabling IGMP only on the receiver LAN does not provide an upstream PIM routing tree. This risk belongs to a different operational problem: Two PIM neighbors run across the same interface but multicast joins never propagate because PIM is disabled on the receiver-facing transit. The stated condition instead exposes this direct risk: Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built. The appropriate mitigation is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
Without an RP for the ASM group, the normal shared tree cannot be established. This risk belongs to a different operational problem: An ASM receiver joins a multicast group through PIM sparse mode, but no rendezvous point mapping exists for that group range. The stated condition instead exposes this direct risk: Unicast ping and valid IGMP membership do not prove the end-to-end multicast tree is built. The appropriate mitigation is: Permit PIM control signaling and expected multicast traffic on the specific authorized transit path.
A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. Which targeted engineering change is MOST directly justified by the observed evidence?
Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. This change specifically addresses the reported evidence: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The relevant protocol mechanism is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag. A decisive acceptance test would be: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
Use a supported private VLAN design with isolated secondary ports and a promiscuous gateway port. This is a valid solution to a different Junos situation: A hosting switch allows isolated customers to access a gateway but the customers must not talk directly to one another inside the same service subnet. It does not directly correct the specific failure evidence here: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The required targeted change is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.
Add the supported LLDP control protocol to the relevant L2PT tunnel treatment. This is a valid solution to a different Junos situation: A service provider already transports customer data VLANs but the remote customer's LLDP frames never reach its opposite endpoint. It does not directly correct the specific failure evidence here: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The required targeted change is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.
Tune the VSTP root bridge priority for that individual VLAN and review path cost. This is a valid solution to a different Junos situation: Two redundant campus uplinks participate in VSTP but the traffic for a specific VLAN takes the uplink intentionally reserved for another segment. It does not directly correct the specific failure evidence here: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The required targeted change is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers.
A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The proposed correction is: Use supported Q-in-Q service VLAN tags to separate the overlapping customer VLAN identifiers. Which observation MOST directly confirms this fault is resolved?
Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100. This is the direct acceptance evidence for the observed failure: A service provider carries two customers using internal VLAN 100 across the same aggregation trunk and must keep their traffic isolated. The mechanism being validated is: IEEE 802.1ad VLAN stacking adds an outer provider tag around the original customer VLAN tag.
Clients can reach the gateway but isolated peer-to-peer Layer 2 frames are blocked. That would validate a different condition: A hosting switch allows isolated customers to access a gateway but the customers must not talk directly to one another inside the same service subnet. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
The customer receives a frame with the expected original inner VLAN tag and no provider S-VLAN tag. That would validate a different condition: A double-tagged customer Ethernet frame arrives at the far edge of a Q-in-Q service with its provider tag still attached. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
The new VLAN is advertised and installed on participating transport trunks without manual additions. That would validate a different condition: A switch trunk intermittently drops newly defined tenant VLANs because each distribution switch has a static VLAN allowlist and no registration updates. The decisive check for the current issue is: Captures show distinct outer S-VLAN tags while preserving each customer's inner C-VLAN 100.
Please check your mailbox for a message from support@examlabs.com and follow the directions.