Pass Juniper JN0-650 Exam in First Attempt Easily
Real Juniper JN0-650 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-650 Premium File

  • 107 Questions & Answers
  • Last Update: Nov 8, 2026
$69.99 $76.99

Enterprise Routing and Switching, Professional (JNCIP-ENT) JN0-650 Practice Test 5

Question 40

A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. If the team bypasses or fails to implement the targeted correction (Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.), which direct operational risk or residual exposure is MOST relevant?

  1. Changing interface metrics does not repair authentication failures and can leave routing disconnected.
  2. A virtual link through a stub transit area or an unavailable transit path cannot restore the backbone connection.
  3. Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations.
  4. Global IPv6 reachability by itself does not establish an OSPFv3 routing adjacency.

Explanation

Correct Answer

A:

Changing interface metrics does not repair authentication failures and can leave routing disconnected. This is the consequence linked to the observed situation: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. It is prevented by: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides. The underlying reason is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.

Incorrect Answers

B:

A virtual link through a stub transit area or an unavailable transit path cannot restore the backbone connection. This risk belongs to a different operational problem: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.

C:

Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. This risk belongs to a different operational problem: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.

D:

Global IPv6 reachability by itself does not establish an OSPFv3 routing adjacency. This risk belongs to a different operational problem: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.

Question 41

The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Constrain the ASBR's export policy to defined route families and inspect the changed LSA database.
  2. Build a term-based export policy matching those exact prefix filters and add a rejecting terminal term.
  3. Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.
  4. Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly.

Explanation

Correct Answer

C:

Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. This change specifically addresses the reported evidence: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The relevant protocol mechanism is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. A decisive acceptance test would be: Only the allowlisted external prefixes appear in downstream external LSAs.

Incorrect Answers

A:

Constrain the ASBR's export policy to defined route families and inspect the changed LSA database. This is a valid solution to a different Junos situation: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. It does not directly correct the specific failure evidence here: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The required targeted change is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

B:

Build a term-based export policy matching those exact prefix filters and add a rejecting terminal term. This is a valid solution to a different Junos situation: A routing engineer wants to export exactly two loopback prefixes from static routes into OSPF, not the entire static route table. It does not directly correct the specific failure evidence here: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The required targeted change is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

D:

Compare configured OSPF interface metrics and choose the intended shortest-path costs explicitly. This is a valid solution to a different Junos situation: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. It does not directly correct the specific failure evidence here: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The required targeted change is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

Question 42

The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The proposed correction is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. Which observation MOST directly confirms this fault is resolved?

  1. The area LSDB includes only approved external advertisements after flooding settles.
  2. The selected external path reflects the defined E2 comparison and tie-break behavior.
  3. Captured OSPF Hellos and database exchange return and the neighbor reaches Full.
  4. Only the allowlisted external prefixes appear in downstream external LSAs.

Explanation

Correct Answer

D:

Only the allowlisted external prefixes appear in downstream external LSAs. This is the direct acceptance evidence for the observed failure: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. The mechanism being validated is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.

Incorrect Answers

A:

The area LSDB includes only approved external advertisements after flooding settles. That would validate a different condition: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. The decisive check for the current issue is: Only the allowlisted external prefixes appear in downstream external LSAs.

B:

The selected external path reflects the defined E2 comparison and tie-break behavior. That would validate a different condition: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The decisive check for the current issue is: Only the allowlisted external prefixes appear in downstream external LSAs.

C:

Captured OSPF Hellos and database exchange return and the neighbor reaches Full. That would validate a different condition: A control-plane policy blocks OSPF IP protocol 89 on one link even though TCP and ICMP connectivity are healthy. The decisive check for the current issue is: Only the allowlisted external prefixes appear in downstream external LSAs.

Question 43

A Junos engineer proposes this response: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. The situation is: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. Which technical principle BEST justifies the response?

  1. OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.
  2. Type-5 external LSAs distribute AS-external reachability across eligible OSPF areas.
  3. Routing policy matches route attributes and explicitly controls redistribution acceptance.
  4. OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone.

Explanation

Correct Answer

A:

OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain. This is the controlling mechanism in the specific case: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. It predicts the acceptance result: Only the allowlisted external prefixes appear in downstream external LSAs.

Incorrect Answers

B:

Type-5 external LSAs distribute AS-external reachability across eligible OSPF areas. This principle explains a separate situation: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. For this issue the relevant mechanism is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.

C:

Routing policy matches route attributes and explicitly controls redistribution acceptance. This principle explains a separate situation: A routing engineer wants to export exactly two loopback prefixes from static routes into OSPF, not the entire static route table. For this issue the relevant mechanism is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.

D:

OSPF's SPF route selection uses accumulated link costs rather than nominal interface speed alone. This principle explains a separate situation: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. For this issue the relevant mechanism is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.

Question 44

The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. If the team bypasses or fails to implement the targeted correction (Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.), which direct operational risk or residual exposure is MOST relevant?

  1. Failing to filter redistributed routes expands LSDB size and may expose undesired routes.
  2. Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area.
  3. Using a catchall accept may accidentally advertise static routes used for management or blackholes.
  4. Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path.

Explanation

Correct Answer

B:

Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. This is the consequence linked to the observed situation: The OSPF database contains an external /24 that operations never intended to leak from a branch redistribution boundary. It is prevented by: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR. The underlying reason is: OSPF export policy controls which eligible non-OSPF routes are injected into the OSPF domain.

Incorrect Answers

A:

Failing to filter redistributed routes expands LSDB size and may expose undesired routes. This risk belongs to a different operational problem: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. The stated condition instead exposes this direct risk: Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. The appropriate mitigation is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

C:

Using a catchall accept may accidentally advertise static routes used for management or blackholes. This risk belongs to a different operational problem: A routing engineer wants to export exactly two loopback prefixes from static routes into OSPF, not the entire static route table. The stated condition instead exposes this direct risk: Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. The appropriate mitigation is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

D:

Leaving inconsistent costs can steer traffic onto a congested or operationally unintended path. This risk belongs to a different operational problem: Two OSPF links carry the same prefix and traffic should use the lower-cost interface rather than the higher-bandwidth interface selected by intuition. The stated condition instead exposes this direct risk: Unrestricted redistribution can advertise unintended infrastructure reachability to every attached area. The appropriate mitigation is: Apply an explicit Junos export policy to select and reject the appropriate redistributed routes at the ASBR.

Question 45

A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace.
  2. Keep the access-facing OSPF interface passive while advertising its connected subnet through the area.
  3. Remove passive operation from only the transit OSPF interface that requires peer formation.
  4. Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

Explanation

Correct Answer

D:

Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost. This change specifically addresses the reported evidence: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The relevant protocol mechanism is: Junos chooses the active route across protocols by route preference before forwarding installation. A decisive acceptance test would be: The active RIB route and forwarding entry identify the intended preferred protocol origin.

Incorrect Answers

A:

Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace. This is a valid solution to a different Junos situation: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. It does not directly correct the specific failure evidence here: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The required targeted change is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

B:

Keep the access-facing OSPF interface passive while advertising its connected subnet through the area. This is a valid solution to a different Junos situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. It does not directly correct the specific failure evidence here: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The required targeted change is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

C:

Remove passive operation from only the transit OSPF interface that requires peer formation. This is a valid solution to a different Junos situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. It does not directly correct the specific failure evidence here: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The required targeted change is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

Question 46

A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The proposed correction is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost. Which observation MOST directly confirms this fault is resolved?

  1. The active RIB route and forwarding entry identify the intended preferred protocol origin.
  2. The selected external path reflects the defined E2 comparison and tie-break behavior.
  3. The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN.
  4. Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent.

Explanation

Correct Answer

A:

The active RIB route and forwarding entry identify the intended preferred protocol origin. This is the direct acceptance evidence for the observed failure: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. The mechanism being validated is: Junos chooses the active route across protocols by route preference before forwarding installation.

Incorrect Answers

B:

The selected external path reflects the defined E2 comparison and tie-break behavior. That would validate a different condition: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The decisive check for the current issue is: The active RIB route and forwarding entry identify the intended preferred protocol origin.

C:

The access subnet appears in the LSDB and no OSPF neighbors form on the edge-facing LAN. That would validate a different condition: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The decisive check for the current issue is: The active RIB route and forwarding entry identify the intended preferred protocol origin.

D:

Neighbor output shows a Full adjacency while passive user LAN interfaces remain silent. That would validate a different condition: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The decisive check for the current issue is: The active RIB route and forwarding entry identify the intended preferred protocol origin.

Question 47

A Junos engineer proposes this response: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost. The situation is: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. Which technical principle BEST justifies the response?

  1. OSPF E2 external routes primarily consider the external metric with internal cost relevant to ties.
  2. Junos chooses the active route across protocols by route preference before forwarding installation.
  3. Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface.
  4. A passive OSPF interface advertises its network but does not establish router neighbors there.

Explanation

Correct Answer

B:

Junos chooses the active route across protocols by route preference before forwarding installation. This is the controlling mechanism in the specific case: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. It predicts the acceptance result: The active RIB route and forwarding entry identify the intended preferred protocol origin.

Incorrect Answers

A:

OSPF E2 external routes primarily consider the external metric with internal cost relevant to ties. This principle explains a separate situation: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. For this issue the relevant mechanism is: Junos chooses the active route across protocols by route preference before forwarding installation.

C:

Passive-interface design advertises an attached network without initiating OSPF adjacency on that interface. This principle explains a separate situation: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. For this issue the relevant mechanism is: Junos chooses the active route across protocols by route preference before forwarding installation.

D:

A passive OSPF interface advertises its network but does not establish router neighbors there. This principle explains a separate situation: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. For this issue the relevant mechanism is: Junos chooses the active route across protocols by route preference before forwarding installation.

Question 48

A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. If the team bypasses or fails to implement the targeted correction (Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.), which direct operational risk or residual exposure is MOST relevant?

  1. Misreading E2 selection as pure internal cost can send remediation to the wrong part of the topology.
  2. Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface.
  3. Changing OSPF cost alone cannot override a more preferred connected route for the same prefix.
  4. Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link.

Explanation

Correct Answer

C:

Changing OSPF cost alone cannot override a more preferred connected route for the same prefix. This is the consequence linked to the observed situation: A router receives an OSPF external route but the design requires preferring a directly connected duplicate destination from a separate source. It is prevented by: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost. The underlying reason is: Junos chooses the active route across protocols by route preference before forwarding installation.

Incorrect Answers

A:

Misreading E2 selection as pure internal cost can send remediation to the wrong part of the topology. This risk belongs to a different operational problem: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The stated condition instead exposes this direct risk: Changing OSPF cost alone cannot override a more preferred connected route for the same prefix. The appropriate mitigation is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

B:

Allowing uncontrolled OSPF neighbors on a user LAN broadens the routing-control-plane attack surface. This risk belongs to a different operational problem: A branch requires OSPF reachability to its attached access LAN but must not form router adjacencies with random hosts on that LAN. The stated condition instead exposes this direct risk: Changing OSPF cost alone cannot override a more preferred connected route for the same prefix. The appropriate mitigation is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

D:

Keeping a transit link passive prevents OSPF Hello adjacency and route exchange across that link. This risk belongs to a different operational problem: A newly added OSPF transit interface is mistakenly set passive and cannot establish neighbors despite physical bidirectional IP reachability. The stated condition instead exposes this direct risk: Changing OSPF cost alone cannot override a more preferred connected route for the same prefix. The appropriate mitigation is: Inspect Junos route preference values and the candidate route flags before manipulating OSPF protocol cost.

Question 49

An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. Which targeted engineering change is MOST directly justified by the observed evidence?

  1. Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace.
  2. Change the topology design to a compatible NSSA and originate permitted external routes there.
  3. Constrain the ASBR's export policy to defined route families and inspect the changed LSA database.
  4. Set matching OSPF area membership for both sides of that transit adjacency.

Explanation

Correct Answer

A:

Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace. This change specifically addresses the reported evidence: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The relevant protocol mechanism is: OSPF E2 external routes primarily consider the external metric with internal cost relevant to ties. A decisive acceptance test would be: The selected external path reflects the defined E2 comparison and tie-break behavior.

Incorrect Answers

B:

Change the topology design to a compatible NSSA and originate permitted external routes there. This is a valid solution to a different Junos situation: A branch OSPF stub area must import selected external routes from its local ASBR without carrying all external type-5 LSAs. It does not directly correct the specific failure evidence here: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The required targeted change is: Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace.

C:

Constrain the ASBR's export policy to defined route families and inspect the changed LSA database. This is a valid solution to a different Junos situation: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. It does not directly correct the specific failure evidence here: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The required targeted change is: Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace.

D:

Set matching OSPF area membership for both sides of that transit adjacency. This is a valid solution to a different Junos situation: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. It does not directly correct the specific failure evidence here: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The required targeted change is: Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace.

Question 50

An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The proposed correction is: Check the external metric type and the internal cost to each ASBR in the OSPF route selection trace. Which observation MOST directly confirms this fault is resolved?

  1. The NSSA advertises its approved type-7 externals and ABR translation behaves as designed.
  2. The selected external path reflects the defined E2 comparison and tie-break behavior.
  3. The area LSDB includes only approved external advertisements after flooding settles.
  4. Neighbor detail reports the intended common area and the area LSDB becomes consistent.

Explanation

Correct Answer

B:

The selected external path reflects the defined E2 comparison and tie-break behavior. This is the direct acceptance evidence for the observed failure: An OSPF external type-2 prefix selects an unexpected egress even though two ASBRs announce the same external metric. The mechanism being validated is: OSPF E2 external routes primarily consider the external metric with internal cost relevant to ties.

Incorrect Answers

A:

The NSSA advertises its approved type-7 externals and ABR translation behaves as designed. That would validate a different condition: A branch OSPF stub area must import selected external routes from its local ASBR without carrying all external type-5 LSAs. The decisive check for the current issue is: The selected external path reflects the defined E2 comparison and tie-break behavior.

C:

The area LSDB includes only approved external advertisements after flooding settles. That would validate a different condition: A core OSPF area receives far too many type-5 external advertisements after a redistribution expansion. The decisive check for the current issue is: The selected external path reflects the defined E2 comparison and tie-break behavior.

D:

Neighbor detail reports the intended common area and the area LSDB becomes consistent. That would validate a different condition: Two OSPF area 0 routers reach bidirectional Hello state, yet one sees a unique area identifier in the other router's received Hello. The decisive check for the current issue is: The selected external path reflects the defined E2 comparison and tie-break behavior.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports