Pass Juniper JN0-364 Exam in First Attempt Easily
Real Juniper JN0-364 Exam Questions, Accurate & Verified Answers As Experienced in the Actual Test!

Verified by experts

JN0-364 Premium File

  • 69 Questions & Answers
  • Last Update: Nov 4, 2026
$69.99 $76.99

Service Provider Routing and Switching, Specialist (JNCIS-SP) JN0-364 Practice Test 34

Question 330

The on-call engineer at Canal City University receives this fault report: A backbone operator needs to prefer a primary egress for all internal routers without changing the external partner's AS path length. What initial check best isolates the actual failing protocol stage?

  1. Compare best paths and local-preference values for the exact prefix on internal speakers and identify the import policy setting it.
  2. Check outbound advertised path attributes and the remote neighbor's policy and MED comparison rules rather than assuming remote local preference.
  3. Check `show bgp neighbor` last-error/state and compare peer AS, local AS, neighbor address and TCP/179 reachability.
  4. Inspect best-path and alternate path attributes, multipath configuration and the forwarding next-hop group for the exact destination.

Correct answer: A

Explanation of each choice

A.

Compare best paths and local-preference values for the exact prefix on internal speakers and identify the import policy setting it. Local preference controls the AS-wide preferred exit before AS-path length, unlike MED which is commonly compared for neighbor ingress selection.

B.

This check may help with another root cause, for example: A provider advertises two links to a neighboring AS and wishes to express a preferred ingress while keeping the links as separate BGP paths. It does not test the first failed condition; start with: Compare best paths and local-preference values for the exact prefix on internal speakers and identify the import policy setting it.

C.

That evidence could be normal while the reported defect persists. It is aimed at: A provider changed a partner's ASN, leaving the old `peer-as` on its Junos BGP group while TCP connection attempts continue. Instead inspect: Compare best paths and local-preference values for the exact prefix on internal speakers and identify the import policy setting it.

D.

The check diagnoses a different layer of service. Its source issue is: Two equal eligible BGP paths to a destination exist, but forwarding uses only the best path while the service design needs shared capacity. The relevant initial check is: Compare best paths and local-preference values for the exact prefix on internal speakers and identify the import policy setting it.

Question 331

The provider operations team at Bridgeway Cloud reports: The provider expects a shorter AS path to win, but another path has a deliberately higher local preference and is selected instead. Which implementation decision best corrects the cause?

  1. Adjust the neighbor's ordered BGP import policy to accept only authorized prefixes and expected attributes, then validate the received and accepted routes.
  2. Enable supported BGP multipath for the intended group and verify the installed forwarding next-hop set under the required path-eligibility constraints.
  3. Restore reachability to the advertised BGP next-hop address through the correct IGP or appropriate next-hop handling, then verify route eligibility.
  4. Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

Correct answer: D

Explanation of each choice

A.

This action may apply to a different problem, for example: A provider receives a malformed or unauthorized customer prefix yet it enters route selection after a loose import policy. It does not repair the stated failure boundary. The case-specific reason is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

B.

The other action is relevant when A router has eBGP paths with equal relevant attributes and the operations team assumes both will automatically enter the forwarding table. The current case instead requires: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required. The distinction is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

C.

That would address a separate configuration fault: A received iBGP route is visible in inet.0 but inactive because its BGP next hop cannot be resolved through the IGP. This stem identifies a different cause, corrected by: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

D.

Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required. The case-specific reason is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference. A direct acceptance test is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

Question 332

During a post-change check at Bridgeway Cloud, the original condition was: The provider expects a shorter AS path to win, but another path has a deliberately higher local preference and is selected instead. What evidence would validate the corrected behavior?

  1. Internal routers choose the policy-preferred egress based on higher local preference before comparing later path-selection attributes.
  2. The neighboring AS receives the intended MED values where applicable and its selected ingress matches the mutually understood path policy.
  3. Received or advertised route detail shows the agreed community on the exact prefixes, and downstream policy actions match its value.
  4. Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

Correct answer: D

Explanation of each choice

A.

This would be valid for another situation: Two paths learned inside one AS reach the same destination; the selected exit conflicts with policy despite the chosen link having fewer AS hops. It does not establish that the failing boundary in this scenario works; verify: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

B.

The observation confirms a different component's behavior. Its source context is: An operator changes local preference on its own router expecting a remote AS to honor it, but the remote side never receives that attribute. In this case the success criterion is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

C.

That check proves something else, such as: A carrier tags customer routes with a standard BGP community to drive downstream policy, but the tag never appears beyond the ingress edge. It could pass while the stated problem remains. The targeted evidence here is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

D.

Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence. AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

Question 333

At Bridgeway Cloud, an engineer is asked to explain this case: The provider expects a shorter AS path to win, but another path has a deliberately higher local preference and is selected instead. Which underlying routing or switching principle accounts for the appropriate solution?

  1. BGP local preference is carried within an autonomous system and favors larger values for route selection; it is not advertised to external eBGP peers.
  2. BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.
  3. MED suggests a preferred entry point to a neighboring AS under its own BGP selection rules; local preference is internal to an AS.
  4. Ordered Junos BGP export policies determine which eligible local routes are advertised to a BGP group or neighbor.

Correct answer: B

Explanation of each choice

A.

That principle belongs to a different service stage: Two paths learned inside one AS reach the same destination; the selected exit conflicts with policy despite the chosen link having fewer AS hops. The directly relevant mechanism is: BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.

B.

BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie. The key distinction is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference. Accordingly the remedy is: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

C.

The statement can be true when A provider advertises two links to a neighboring AS and wishes to express a preferred ingress while keeping the links as separate BGP paths. But it does not explain the reported failure. Here: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

D.

That principle belongs to a different service stage: An edge advertises unapproved internal prefixes after an operator broadens a BGP export term beyond the intended customer route set. The directly relevant mechanism is: BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.

Question 334

A risk assessment at Bridgeway Cloud identifies: The provider expects a shorter AS path to win, but another path has a deliberately higher local preference and is selected instead. Which practical consequence is most specifically tied to this failure?

  1. Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.
  2. Parts of the AS can lack routes despite each router having some established iBGP neighbors.
  3. Routes are never exchanged with the partner, even if ICMP reachability tests across the physical link succeed.
  4. An unresolvable BGP route may be received but never forwarded, making the prefix unreachable to customers.

Correct answer: A

Explanation of each choice

A.

Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress. The direct mitigation is: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

B.

It is a risk in another topology or protocol state: A provider adds more iBGP speakers without a route-reflector or full-mesh design and assumes iBGP will transitively flood routes. Here the most direct failure path is: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

C.

The concern could occur elsewhere when Two neighboring providers configured for eBGP have IP reachability but the BGP session remains Active because one side uses the wrong peer AS number. For the stated scenario, the immediate risk is: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

D.

That consequence is more closely associated with another deficiency, such as: A service route remains hidden after an eBGP-to-iBGP handoff; the internal router knows the prefix but not a path to its advertised next hop. The described fault instead exposes: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

Question 335

The on-call engineer at Bridgeway Cloud receives this fault report: The provider expects a shorter AS path to win, but another path has a deliberately higher local preference and is selected instead. What initial check best isolates the actual failing protocol stage?

  1. Inspect best-path and alternate path attributes, multipath configuration and the forwarding next-hop group for the exact destination.
  2. Check outbound advertised path attributes and the remote neighbor's policy and MED comparison rules rather than assuming remote local preference.
  3. Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.
  4. Inspect the prefix's community list before and after import/export policy and compare route term ordering.

Correct answer: C

Explanation of each choice

A.

That evidence could be normal while the reported defect persists. It is aimed at: Two equal eligible BGP paths to a destination exist, but forwarding uses only the best path while the service design needs shared capacity. Instead inspect: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

B.

The check diagnoses a different layer of service. Its source issue is: An operator changes local preference on its own router expecting a remote AS to honor it, but the remote side never receives that attribute. The relevant initial check is: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

C.

Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency. AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

D.

That evidence could be normal while the reported defect persists. It is aimed at: A neighbor's agreed selective-routing behavior fails because a community is added after the rejecting export term rather than before policy selection. Instead inspect: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

Question 336

A production change request at Crestpoint Research includes this finding: Two eBGP routes have equal earlier BGP decision attributes and the operator needs to explain why a path with fewer AS numbers is preferred. What should the engineer change to address it?

  1. Restore reachability to the advertised BGP next-hop address through the correct IGP or appropriate next-hop handling, then verify route eligibility.
  2. Use an appropriate externally communicated MED or an agreed inbound routing policy and verify the neighbor's comparison behavior and limitations.
  3. Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.
  4. Constrain Junos BGP export terms to approved active prefixes and attributes, preserving explicit accept/reject behavior for the neighbor.

Correct answer: C

Explanation of each choice

A.

That would address a separate configuration fault: A service route remains hidden after an eBGP-to-iBGP handoff; the internal router knows the prefix but not a path to its advertised next hop. This stem identifies a different cause, corrected by: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

B.

This action may apply to a different problem, for example: A provider advertises two links to a neighboring AS and wishes to express a preferred ingress while keeping the links as separate BGP paths. It does not repair the stated failure boundary. The case-specific reason is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

C.

Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required. The case-specific reason is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference. A direct acceptance test is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

D.

That would address a separate configuration fault: A transit customer prefix is locally active but never advertised to an approved eBGP neighbor because the export policy's final term rejects it. This stem identifies a different cause, corrected by: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

Question 337

After Crestpoint Research applies its proposed fix to this problem — Two eBGP routes have equal earlier BGP decision attributes and the operator needs to explain why a path with fewer AS numbers is preferred. — which observation best proves the specific failure has been resolved?

  1. Received or advertised route detail shows the agreed community on the exact prefixes, and downstream policy actions match its value.
  2. The neighbor receives only intended active advertised routes with correct attributes; internal and reserved prefixes are not leaked.
  3. The intended prefix appears as an eligible received route while blocked prefixes remain rejected, with policy counters matching the design.
  4. Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

Correct answer: D

Explanation of each choice

A.

That check proves something else, such as: A neighbor's agreed selective-routing behavior fails because a community is added after the rejecting export term rather than before policy selection. It could pass while the stated problem remains. The targeted evidence here is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

B.

This would be valid for another situation: A transit customer prefix is locally active but never advertised to an approved eBGP neighbor because the export policy's final term rejects it. It does not establish that the failing boundary in this scenario works; verify: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

C.

The observation confirms a different component's behavior. Its source context is: A planned customer route appears in the partner's advertisements but Junos rejects it at an early inbound policy term. In this case the success criterion is: Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence.

D.

Best-path output shows the anticipated winner with equal preceding attributes and the intended AS-path length or policy influence. AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

Question 338

An architecture review at Crestpoint Research examines the following symptom: Two eBGP routes have equal earlier BGP decision attributes and the operator needs to explain why a path with fewer AS numbers is preferred. What Junos or protocol mechanism is most directly responsible?

  1. Ordered Junos BGP export policies determine which eligible local routes are advertised to a BGP group or neighbor.
  2. A BGP route must have a resolvable next hop before it can become active and install usable forwarding state.
  3. Junos BGP import policy screens and modifies routes as they enter BGP route consideration rather than controlling what the local router advertises outward.
  4. BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.

Correct answer: D

Explanation of each choice

A.

The statement can be true when An edge advertises unapproved internal prefixes after an operator broadens a BGP export term beyond the intended customer route set. But it does not explain the reported failure. Here: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

B.

That principle belongs to a different service stage: A received iBGP route is visible in inet.0 but inactive because its BGP next hop cannot be resolved through the IGP. The directly relevant mechanism is: BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.

C.

This explains a separate protocol behavior: A planned customer route appears in the partner's advertisements but Junos rejects it at an early inbound policy term. In the current facts, the controlling mechanism is: BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie.

D.

BGP path selection evaluates several attributes in order; AS-path length is a criterion only after higher-priority decision factors tie. The key distinction is: AS-path manipulation may influence selection, but cannot be assumed to override higher local preference. Accordingly the remedy is: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

Question 339

The team at Crestpoint Research defers a fix for this condition: Two eBGP routes have equal earlier BGP decision attributes and the operator needs to explain why a path with fewer AS numbers is preferred. What failure is most likely if no targeted control is applied?

  1. Blocking a required message class causes hold-time expiration, session resets or missing reachability updates despite an otherwise healthy link.
  2. An unresolvable BGP route may be received but never forwarded, making the prefix unreachable to customers.
  3. Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.
  4. Routes are never exchanged with the partner, even if ICMP reachability tests across the physical link succeed.

Correct answer: C

Explanation of each choice

A.

The concern could occur elsewhere when An intermittent control-plane firewall blocks one BGP packet class, and operators need to separate OPEN, KEEPALIVE, UPDATE and NOTIFICATION behavior. For the stated scenario, the immediate risk is: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

B.

That consequence is more closely associated with another deficiency, such as: A received iBGP route is visible in inet.0 but inactive because its BGP next hop cannot be resolved through the IGP. The described fault instead exposes: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

C.

Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress. The direct mitigation is: Verify the applicable earlier decision attributes, then compare AS path length and apply an approved AS-path policy if a deliberate longer path is required.

D.

The concern could occur elsewhere when Two neighboring providers configured for eBGP have IP reachability but the BGP session remains Active because one side uses the wrong peer AS number. For the stated scenario, the immediate risk is: Misunderstanding selection order can result in ineffective prepend changes and incorrect assumptions about the chosen egress.

Question 340

During provider troubleshooting at Crestpoint Research, this symptom is observed: Two eBGP routes have equal earlier BGP decision attributes and the operator needs to explain why a path with fewer AS numbers is preferred. Which targeted inspection should precede remediation?

  1. Inspect the prefix's community list before and after import/export policy and compare route term ordering.
  2. Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.
  3. Check `show bgp neighbor` last-error/state and compare peer AS, local AS, neighbor address and TCP/179 reachability.
  4. Inspect received advertised routes, route-hidden reasons and the exact ordered import policy attached to the BGP group.

Correct answer: B

Explanation of each choice

A.

This check may help with another root cause, for example: A neighbor's agreed selective-routing behavior fails because a community is added after the rejecting export term rather than before policy selection. It does not test the first failed condition; start with: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

B.

Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency. AS-path manipulation may influence selection, but cannot be assumed to override higher local preference.

C.

The check diagnoses a different layer of service. Its source issue is: A provider changed a partner's ASN, leaving the old `peer-as` on its Junos BGP group while TCP connection attempts continue. The relevant initial check is: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

D.

This check may help with another root cause, for example: A provider receives a malformed or unauthorized customer prefix yet it enters route selection after a loose import policy. It does not test the first failed condition; start with: Inspect all candidate BGP path attributes in selection order, especially local preference and AS-path list, rather than only ping latency.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

SPECIAL OFFER: GET 10% OFF
This is ONE TIME OFFER

You save
10%

Enter Your Email Address to Receive Your 10% Off Discount Code

SPECIAL OFFER: GET 10% OFF

You save
10%

Use Discount Code:

A confirmation link was sent to your e-mail.

Please check your mailbox for a message from support@examlabs.com and follow the directions.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your email address below to get started with our interactive software demo of your free trial.

  • Realistic exam simulation and exam editor with preview functions
  • Whole exam in a single file with several different question types
  • Customizable exam-taking mode & detailed score reports