JN0-650 Premium File
- 107 Questions & Answers
- Last Update: Nov 8, 2026
OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. The proposed correction is: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output. Which observation MOST directly confirms this fault is resolved?
The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface. This is the direct acceptance evidence for the observed failure: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. The mechanism being validated is: OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.
Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous. That would validate a different condition: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The decisive check for the current issue is: The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface.
Adjacent areas learn the expected aggregate while specific routes remain visible inside the originating area. That would validate a different condition: An enterprise intends to carry summarized inter-area OSPF reachability rather than thousands of individual branch loopback routes. The decisive check for the current issue is: The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface.
The partner sees an aggregate covering precisely the intended networks, with valid contributors. That would validate a different condition: An OSPFv2 adjacency to an external partner remains Full, but the partner expects a summarized route that the ABR is not advertising. The decisive check for the current issue is: The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface.
A Junos engineer proposes this response: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output. The situation is: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. Which technical principle BEST justifies the response?
OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability. This is the controlling mechanism in the specific case: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. It predicts the acceptance result: The expected OSPFv3 peer and learned IPv6 routes appear on the intended interface.
OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types. This principle explains a separate situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. For this issue the relevant mechanism is: OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.
Junos import policies and route selection can affect installation independently of LSDB adjacency. This principle explains a separate situation: After a maintenance change, OSPFv2 routes vanish from inet.0 but the protocol neighbor remains Full and LSAs are present. For this issue the relevant mechanism is: OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.
Inter-area summary generation depends on area boundary configuration and eligible contributors. This principle explains a separate situation: An OSPFv2 adjacency to an external partner remains Full, but the partner expects a summarized route that the ABR is not advertising. For this issue the relevant mechanism is: OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.
OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. If the team bypasses or fails to implement the targeted correction (Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output.), which direct operational risk or residual exposure is MOST relevant?
Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. This is the consequence linked to the observed situation: OSPFv3 interfaces advertise IPv6 prefixes, but the operator checks only IPv4 OSPFv2 state while the IPv6 neighbor never appears. It is prevented by: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output. The underlying reason is: OSPFv3 exchanges neighbors using IPv6 link-local signaling and advertises IPv6 reachability.
Global IPv6 reachability by itself does not establish an OSPFv3 routing adjacency. This risk belongs to a different operational problem: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The stated condition instead exposes this direct risk: Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. The appropriate mitigation is: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output.
Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. This risk belongs to a different operational problem: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The stated condition instead exposes this direct risk: Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. The appropriate mitigation is: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output.
Using a catchall accept may accidentally advertise static routes used for management or blackholes. This risk belongs to a different operational problem: A routing engineer wants to export exactly two loopback prefixes from static routes into OSPF, not the entire static route table. The stated condition instead exposes this direct risk: Troubleshooting only the OSPFv2 IPv4 instance can miss an entirely absent OSPFv3 adjacency. The appropriate mitigation is: Verify OSPFv3 protocol and interface participation using IPv6-aware neighbor and route output.
Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. Which targeted engineering change is MOST directly justified by the observed evidence?
Assign unique stable 32-bit OSPF router IDs to the two participating devices. This change specifically addresses the reported evidence: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The relevant protocol mechanism is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes. A decisive acceptance test would be: Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous.
Verify OSPFv3 activation and permitted IPv6 link-local multicast signaling on that link. This is a valid solution to a different Junos situation: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. It does not directly correct the specific failure evidence here: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The required targeted change is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
Check inter-area prefix LSAs and ABR route policy rather than assuming the missing prefixes are in router LSAs. This is a valid solution to a different Junos situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. It does not directly correct the specific failure evidence here: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The required targeted change is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
Compare OSPF database records and neighbor synchronization states on both ABRs. This is a valid solution to a different Junos situation: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. It does not directly correct the specific failure evidence here: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The required targeted change is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The proposed correction is: Assign unique stable 32-bit OSPF router IDs to the two participating devices. Which observation MOST directly confirms this fault is resolved?
Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous. This is the direct acceptance evidence for the observed failure: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. The mechanism being validated is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes.
A capture shows IPv6 link-local Hellos and an OSPFv3 peer appears as expected. That would validate a different condition: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The decisive check for the current issue is: Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous.
The appropriate inter-area-prefix LSAs and accepted IPv6 routes appear for target networks. That would validate a different condition: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The decisive check for the current issue is: Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous.
Database summaries reconcile and neighbor state reports Full after successful exchange. That would validate a different condition: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. The decisive check for the current issue is: Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous.
A Junos engineer proposes this response: Assign unique stable 32-bit OSPF router IDs to the two participating devices. The situation is: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. Which technical principle BEST justifies the response?
OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes. This is the controlling mechanism in the specific case: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. It predicts the acceptance result: Each peer appears under a distinct router ID and its link-state advertisements remain unambiguous.
OSPFv3 neighbors normally exchange control messages using IPv6 link-local addressing. This principle explains a separate situation: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. For this issue the relevant mechanism is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes.
OSPFv3 separates topology information from IPv6 prefix information in dedicated LSA types. This principle explains a separate situation: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. For this issue the relevant mechanism is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes.
An OSPF adjacency needs synchronized link-state databases in addition to basic reachability. This principle explains a separate situation: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. For this issue the relevant mechanism is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes.
Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. If the team bypasses or fails to implement the targeted correction (Assign unique stable 32-bit OSPF router IDs to the two participating devices.), which direct operational risk or residual exposure is MOST relevant?
Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. This is the consequence linked to the observed situation: Two OSPFv3 peers have valid routed IPv6 connectivity but advertise duplicate router IDs during adjacency startup. It is prevented by: Assign unique stable 32-bit OSPF router IDs to the two participating devices. The underlying reason is: OSPFv3 uses an IPv4-formatted 32-bit router ID even when exchanging IPv6 routes.
Global IPv6 reachability by itself does not establish an OSPFv3 routing adjacency. This risk belongs to a different operational problem: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The stated condition instead exposes this direct risk: Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. The appropriate mitigation is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
Looking only for IPv6 prefixes in OSPFv3 router LSAs can hide the actual prefix propagation problem. This risk belongs to a different operational problem: OSPFv3 has a stable neighbor but IPv6 destination prefixes learned from another area never appear in routing output. The stated condition instead exposes this direct risk: Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. The appropriate mitigation is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
Assuming ping success proves LSDB correctness can leave SPF decisions inconsistent. This risk belongs to a different operational problem: Two adjacent OSPF ABRs have different LSDB checksums after a link flap, while operational staff look only at interface ping success. The stated condition instead exposes this direct risk: Duplicate router IDs can cause ambiguous topology identity and unstable OSPFv3 neighbor formation. The appropriate mitigation is: Assign unique stable 32-bit OSPF router IDs to the two participating devices.
A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. Which targeted engineering change is MOST directly justified by the observed evidence?
Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides. This change specifically addresses the reported evidence: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The relevant protocol mechanism is: OSPFv2 authenticated adjacencies validate received packet authentication before using them. A decisive acceptance test would be: Authenticated OSPF Hellos are accepted and the peer database reaches Full.
Design a supported OSPF virtual link over the common nonstub transit area and document its operational dependence. This is a valid solution to a different Junos situation: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. It does not directly correct the specific failure evidence here: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The required targeted change is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
Align the intended OSPF network type and related election behavior on the two participating interfaces. This is a valid solution to a different Junos situation: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. It does not directly correct the specific failure evidence here: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The required targeted change is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
Verify OSPFv3 activation and permitted IPv6 link-local multicast signaling on that link. This is a valid solution to a different Junos situation: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. It does not directly correct the specific failure evidence here: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The required targeted change is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The proposed correction is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides. Which observation MOST directly confirms this fault is resolved?
Authenticated OSPF Hellos are accepted and the peer database reaches Full. This is the direct acceptance evidence for the observed failure: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. The mechanism being validated is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.
The remote area has a logical backbone adjacency through the intended transit area after validation. That would validate a different condition: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. The decisive check for the current issue is: Authenticated OSPF Hellos are accepted and the peer database reaches Full.
The neighbor database reaches Full with the expected point-to-point or broadcast behavior. That would validate a different condition: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The decisive check for the current issue is: Authenticated OSPF Hellos are accepted and the peer database reaches Full.
A capture shows IPv6 link-local Hellos and an OSPFv3 peer appears as expected. That would validate a different condition: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The decisive check for the current issue is: Authenticated OSPF Hellos are accepted and the peer database reaches Full.
A Junos engineer proposes this response: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides. The situation is: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. Which technical principle BEST justifies the response?
OSPFv2 authenticated adjacencies validate received packet authentication before using them. This is the controlling mechanism in the specific case: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. It predicts the acceptance result: Authenticated OSPF Hellos are accepted and the peer database reaches Full.
OSPF virtual links can logically connect an area to the backbone through a qualifying transit area. This principle explains a separate situation: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. For this issue the relevant mechanism is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.
OSPF network type determines neighbor and DR election behavior and must match the link design. This principle explains a separate situation: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. For this issue the relevant mechanism is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.
OSPFv3 neighbors normally exchange control messages using IPv6 link-local addressing. This principle explains a separate situation: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. For this issue the relevant mechanism is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.
A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. If the team bypasses or fails to implement the targeted correction (Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.), which direct operational risk or residual exposure is MOST relevant?
Changing interface metrics does not repair authentication failures and can leave routing disconnected. This is the consequence linked to the observed situation: A secure OSPFv2 transit link stops accepting neighbor packets after a key-roll event; captures show incompatible configured authentication secrets. It is prevented by: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides. The underlying reason is: OSPFv2 authenticated adjacencies validate received packet authentication before using them.
A virtual link through a stub transit area or an unavailable transit path cannot restore the backbone connection. This risk belongs to a different operational problem: A remote OSPF area has no physical connection to backbone area 0, and a permitted common transit area exists between its ABR and a backbone ABR. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
Incorrect network-type assumptions can strand neighbors or create inconsistent DR expectations. This risk belongs to a different operational problem: Two OSPFv2 peers progress through adjacency but database exchange fails when their area link settings disagree about network type on the Ethernet circuit. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
Global IPv6 reachability by itself does not establish an OSPFv3 routing adjacency. This risk belongs to a different operational problem: An OSPFv3 edge interface has a valid global IPv6 address but no exchange of OSPFv3 Hellos is observed. The stated condition instead exposes this direct risk: Changing interface metrics does not repair authentication failures and can leave routing disconnected. The appropriate mitigation is: Synchronize the supported OSPF authentication type, key identifier, and shared secret on both sides.
Please check your mailbox for a message from support@examlabs.com and follow the directions.